Best Electric Bikes With 4-Year Warranty & At-Home Trial | EVELO
Owner's Manual for EVELO models including: EVO-2 Display, Bicycle Device, EVO-2 Display Bicycle Device
Atlas EVO-2 Display : Customer Support
File Info : application/pdf, 8 Pages, 598.20KB
DocumentDocumentEVO-2 Display OWNER'S MANUAL Our Team is here to help 7 days a week contact@evelo.com | 877-991-7272 Feel free to reach out! EVELO.COM Display and Keypad Level "+" Level "-" Mode Power Light Indicator Speed Tripometer Odometer Estimated Range Trip Time Max Speed Average Speed Time Error Indicator Battery Voltage or Battery Percentage Current Power Usage Pedal Assist Level DPC-18 DISPLAY 2 Using Your Bike Powering the Bike ON/OFF Hold the ON/OFF button to power on the bike. Hold down the ON/OFF button for two seconds to turn the bike off. Speedometer The speed is shown in the middle of the screen. You can choose miles or kilometers in the settings menu. Pedal Assist Level Selection Press the + or - button to select your pedal assist level. You can choose from 0 to 5, with 0 being no assistance and 5 the most assistance. Light Usage Press and hold the + button for two seconds to turn on the bike's lights. Repeat to turn them off. This will also change the display between day and night mode. Battery Indicator The battery's state of charge is shown as a bar and as a percentage by default. You can also change it to read actual voltage in the Settings Menu. The indicator will turn red when below 20%. Trip Odometer Reset To reset the trip odometer, hold the + and - buttons for a few seconds. Error Code Indicator If there is something wrong with the electronic control system, the error symbol and number will be displayed in the bottom of screen. If you get an error code, contact us for information. (Full list of codes can be found on page 6.) DPC-18 DISPLAY 3 Settings Menu Double tap the Mode button very quickly to enter the Settings menu, click + or - to select the item, then click MODE again. Then you can press + or - to select the desired parameter, and after the parameters have been changed, click Mode again. You can change the following settings: System Units You can choose between metric and imperial units. Brightness Set the brightness of the display. Auto OFF Your bike will turn off after a period of inactivity. Set the length of that period here from 1 to 9 minutes. If you set this to OFF, the bike will not shut itself off. Battery Indicator Shows the battery level as either voltage or percent. Power Indicator Power can be displayed either as Watts (power) or Amps (current). Clock Set the date and time. Start Password You can set a password to use the bike and to access the settings. The default password is 1919. If you change the password and forget it, we cannot unlock it; the display will have to be replaced. DPC-18 DISPLAY 4 Settings Menu Wheel Set your wheel size. It is set correctly from the factory. You can reference the tire size printed on the tire or contact us for more information if needed. Battery Select the battery voltage for your bike. Please do not change this value, as it may result in the bike not functioning. USB Port Turns the USB port on or off. It can charge an external device at 5V 500mA. If you set this to OFF, the USB port will not charge other devices. Light Sensor Turn the light sensor on or off and adjust the sensitivity. The sensor will automatically turn your lights on in low light situation when set to ON. Advanced Settings To access these settings, the default password is 1919. Speed Limit For most models, the max speed is 20 mph by default. When you reach the specified speed, assistance will turn off. The limit can be reaised, but you should check your local laws before doing so. The Atlas, as a Class 3 bike, has a 28 mph speed limit and this setting cannot be changed. Assist Levels Set the number of assist levels to either 3, 5, or 9. This will not change the motor's max output, but changes how fine the adjustment is. DPC-18 DISPLAY 5 Settings Menu Error Code Any error codes are stored here, even after they go away on the main screen. See below for list of codes. Factory Setting This will reset your display back to its factory settings. Information Shows some information about the bike, such as Average and Max Speed, as well as the trip and total odometer. Battery Info Shows detailed information about the battery, though none of it is especially useful to the user. Error Codes 04 Throttle on high position - Flick throttle and restart bike 05 Throttle error 07 High Voltage Protection 08 Motor hall sensor error 09 Motor phase error 10 Controller over temperature 11 Motor over temperature 12 Current sensor error 13 Battery temperature sensor error 14 Motor temperature sensor error 15 Controller temperature sensor error 21 Speed sensor error - Check alignment of magnet and sensor 22 BMS Communication error 23 Headlight error 24 Ambient light sensor error 25 Torque sensor error - torque 26 Torque sensor error - speed 30 Communication error DPC-18 DISPLAY 6 Notes: DPC-18 DISPLAY 7 Questions? Get In Touch: 877-991-7272 contact@evelo.com EVELO.COM First Edition DPC-18 DISPLAY 8