AENAYRIM

Specifications

The parameters above are derived from the laboratory of AENAYRIM. The actual parameters may differ from product to product or from other factors. All images shown here are for reference only.

Overview

The charger features the following components:

• Charging area: The surface where the phone is placed for wireless charging.
• Rotating locking knob (for securing the bracket): Used to adjust and secure the angle of the car mount.
• Extendable Type-C cable: Connects the charger to a power source.
• Wireless charger locking knob: Secures the wireless charger unit to the bracket.
• Air vent clip: Attaches the mount to the car's air vent.
• Fixed air vent hook: A part of the clip that grips the air vent.

Fittings Included

The package contains:

• Cleaning Wipe x 2
• Metal Ring x 2
• Transparent Sticker x 2

Installation Instructions

Follow these steps to install the car mount:

1. Insert the locking knob into the car mount bracket.
2. Connect the locking knob assembly to the wireless charger.
3. Secure the knob to tighten the connection.
4. The assembled unit is the finished product.
5. To attach to an air vent: Twist the locking knob. The clip will stretch out and lock onto the air vent.

Operating Instructions

The charger can be used under the following conditions:

1. Use without a magnetic ring: For iPhone X or newer series phones. The phone will be automatically attached to the charger.
2. Use with Magsafe cases: For iPhone X or newer series phones with Magsafe compatible cases. The phone attaches magnetically through the case.
3. Use with magnetic ring: For iPhone X or newer series phones with non-magnetic cases. Attach the included metal ring to the phone or case.

Assembling the Magnetic Ring

There are two ways to attach the magnetic ring:

• For a bare phone: Stick the transparent sticker onto the back of the phone, then attach the magnetic ring onto the sticker.
• For a phone case: Stick the magnetic ring directly onto the back of the phone case. The transparent sticker is not needed in this case.

Instructions (with the transparent sticker):

1. Use a cleaning wipe to clean the back of the phone or phone case.
2. Remove the cover of the transparent sticker and place it at the center of the back of your phone or phone case.
3. Tear off the paper backing of the magnetic ring and paste it onto the sticker. The installation is now complete.

Note: After pasting the magnetic ring, please wait 24 hours. This allows the magnetic wireless car charger to hold your phone firmly. [checkmark symbol]

Product Structural Features

• This product is a car mount with a built-in high-speed wireless charger, compatible with iPhone X and higher models.
• The rear fixed screw and expandable clamp design are compatible with air vent blades ranging from 3mm to 30mm, ensuring broad compatibility.
• It features built-in foreign object detection and temperature sensing chips for automatic overheat protection and foreign object detection.
• The magnet utilizes N52 neodymium iron boron, providing strong and stable magnetic attraction.
• Crafted from aluminum alloy, the product boasts a sleek and compact design with smooth and effortless extension.

Attentions

1. Avoid dropping the device.
2. Do not install the car mount while driving.
3. Do not install the car mount in locations that could interfere with the airbag or driving visibility.
4. Keep this product away from other magnetic items; otherwise, demagnetization might occur.
5. Keep the car mount away from children.
6. Ensure the wireless charger's main unit and components are assembled correctly, and the wireless charger's rear fixing hook is securely attached to the mount.
7. Connect the wireless charger to the car's Type-C port. Place devices with wireless charging capabilities in the designated area for automatic charging.
8. This wireless charger has a sensing distance of less than or equal to 5mm. It will not function properly if the sensing distance is exceeded or if foreign objects interfere.
9. Verify that the wireless charger is properly connected and that your device supports wireless charging and is compatible with this product.

Warranty Clause

The warranty for the product is valid for a period of 12 months from the original date of purchase.

The warranty applies only to the original consumer purchaser of the product (the "Consumer") and is not assignable or transferable to any subsequent consumer.

The warranty does not apply if the product has not been used in accordance with the instructions or in its normal and customary manner.

FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.