K7mini Operation Guide

Install Noo-psyche APP

First, download the Noo-psyche APP. Install the Noo-Psyche APP on your device and "Allow Noo-Psyche to access this device's location" to continue.

• iOS: Download from App Store
• Android: Download from www.noo-psyche.com/Userguidance or scan the QR code.

Keys Instruction

The device has two control keys: 'L' and 'R'.

Notice: Only the light always on Blue (auto) can connect to the APP.

Connection Mode

There are two methods for the APP to connect to the light: AP mode or LAN mode. Both methods can be used as long as the connection is established.

How to know if the light is on LAN or AP connection mode?

How to Switch LAN and AP mode of the light?

AP Connection

1. Switch the light on AP mode. Refer to the "Connection Mode" section above.
2. Open the APP, click the Portrait icon.
3. Click Apply Permission, and allow Noo-Psyche to access location.
4. Click SWITCHING NETWORK. Click WLAN and ensure it is on. Find the network named "K7_mini****" in the WLAN list, enter the password (12345678), and click connect.
5. Last step, confirm it is AP connection and click SAVE.

Function

After the APP and the light are connected, access the options according to your reef tank type. There are two running modes: manual and auto. Example: LPS.

Default spectrum preset

There are SPS, LPS, and SPS/LPS default spectrum presets. To use the default spectrum settings, select Auto, click FACTORY SETTINGS, and finally click SAVE.

The interface allows viewing spectrum graphs for SPS, LPS, and S/L modes. It also provides options for Auto, Demo Mode, FACTORY SETTINGS, RESET, and SAVE.

Manual - One click viewing

Select LPS. Switch to Manual mode. Adjust the brightness using the progress bar, then click SAVE.

The interface shows K7 MINI with a manual mode slider for brightness adjustment, along with options for Factory, Reset, and Save.

Auto – Sunrise and sunset scene simulation

Modify parameters:

1. Click Auto.
2. Click TIME POINT SETTING.
3. Click EDIT to modify channel parameters.
4. Set the brightness of each channel at the time point, click confirm. Click close when all is done.
5. Click SAVE. To quickly check the spectrum, click Demo Mode.

The system time is displayed, and users can set time points and brightness for different channels. The interface includes options for CANCEL, CONFIRM, FACTORY SETTINGS, RESET, and SAVE. A green dot on the homepage indicates LPS setting is running.

Export/Input spectrum settings

Click Export to download your spectrum settings QR code, which will be saved in the photo album. Click Import to upload your saved QR code, then click save.

Configuring Master/Slave Lighting

How to switch the light to Master or Slave?

1. Slaves: When the LED indicator is always on, press and hold the L key until the LED indicator turns green, then release it. Click the L key again (the green indicator light flashes) to enter standby mode. All slaves should do the same.
2. Master: When the LED indicator is always on blue, press and hold the L key. Release it when the indicator flashes. The master sends a command to the slave, and the slave's green indicator stops flashing.

Note: After adding a new light as a slave, if its brightness differs from other slaves, you can sync them. Operation: Click the L key of the Master to turn the indicator red. Press and hold the L key until the indicator flashes red, then release the L key to send data to the slaves for synchronization.

LAN connection

Noo-Psyche lights only support a separate 2.4GHz routing band. If your 5GHz and 2.4GHz bands are combined, the light cannot pair with Wi-Fi through LAN mode.

Before LAN connection, set a separate SSID for the 2.4GHz routing band:

In your router's wireless settings, navigate to the Wireless page. The entry address is usually on a label attached to the back of the router. If a routing band merging option exists, cancel the merging. Go to the 2.4 GHz setting page and set the Wi-Fi name (SSID) to (XXX)-2.4G, where XXX indicates your Wi-Fi name. Save the settings. Please search online for specific operations if needed.

1. First, confirm the light is in LAN mode. With the blue indicator light on, press and hold the R key until the indicator flashes blue, then release the key to enter network waiting configuration state.
2. Connect your phone device to the Wi-Fi of the 2.4GHz routing band. Open the app, click the Portrait icon, and click "Apply Permission" to "Allow Noo-Psyche to access this device's location".
3. Select LAN connection and enter the Wi-Fi password of the 2.4GHz routing band. Click save. The device will attempt to connect, which should finish in about 30 seconds. Finally, click OK.

Factory Reset

When the LED indicator is always on red, press and hold the R Key until the indicator turns off. NOTE: ONCE THE LIGHT IS RESET TO FACTORY SETTINGS, ITS CONNECTION TO THE DEVICE WILL BE CANCELLED!

WARNING:

1. POWER OFF MEMORY FUNCTION: IT WILL RUN THE LAST SAVING SETTING WHEN THE LIGHT IS TURNED ON.
2. DO NOT SUDDENLY INCREASE THE BRIGHTNESS; OTHERWISE, IT WILL HARM CORALS AND CAUSE CORAL NERVOUSNESS, BLEACHING, OR EVEN DEATH.
3. IF SWITCHING FROM WEAK LIGHTS TO THIS LIGHT, IT IS RECOMMENDED TO SET THE INITIAL TOTAL BRIGHTNESS AT 50%.

Warranty

All Noo-Psyche (NP) products have a 12-month warranty service from the date of purchase. If there is a quality problem within the warranty period, Noo-Psyche will repair or replace the parts free of charge.

The warranty does not cover damage caused by modification, accident, mishandling, misuse, or unauthorized repairs. Exclusions from the warranty include, but are not limited to, damage due to misuse or abuse, such as using modified bulbs and modifying electrical circuits.

Specification

• Size: 116*55mm
• Weight: 0.35kg/0.77lb
• Power: 60W
• Voltage: 100-240V 50/60Hz 1.5A
• Warranty: one year
• Factory URL: www.noo-psyche.com