Primos Killer B Strutting Gobbler Decoy

Components of Killer B™

• Strutting Gobbler Decoy
• Fold-up Silk Fan
• Mobile™ Series Real Fan Holder
• Fan Hardware
• Ground Breaker™ Decoy Stake
• Carrying Bag with Safety Orange Flag
• 90' Pull Line

Killer B™ Strutting Gobbler Decoy

2 Piece Ground Breaker™ Decoy Stake
Model No. 69044

Fold-Up Silk Fan
Model No. 69047

Mobile™ Series Real Fan Holder
Model No. 69048
(for using your own fan)

Carrying Bag with Safety Orange Flag
Model No. 69046

90' Pull Line

Killer B™ Fan Hardware
• (4) Large fender washers are for use on the Mobile™ Series Fan Holder and Fold-up Silk Fan.
• (2) 1/4" Wing Nuts

WARNING: Killer B™ is so realistic, you need to use a blaze orange safety flag when carrying him through the woods. ?

Before Start

Use one of the following methods to get Killer B™ to regain his shape:

• Place Killer B™ under HOT water.
• Use a hair dryer to warm Killer B™.
• Place Killer B™ outside on a warm sunny day.

These methods will pop him back into his original shape.

Assembly of Killer B™

Step 1 - INSTALL STAKE INTO DECOY

Make sure that the stake gets installed through the stabilizer bracket during installation.

Diagram 1 Description: Illustrates the assembly of the decoy stake. It shows a wing nut, washer, the front of the decoy, the top section of the stake, a twist point, a foot peg, and the bottom section of the stake with a welded side piece. The stake is shown inserted into the decoy.

NOTE: Bottom section of stake easily installs and removes for compact carry.

Step 2 - ATTACH SILK FAN TO FAN BRACKET

Diagram 2 Description: Shows the fan bracket with plastic rods, a wing nut, two washers, and a fan screw. The fan is being attached to the bracket.

NOTE: For added realism add real feathers to the Mobile™ Series Real Fan Holder. (See Next Page)

TIP: You may trim Killer B's™ beard to the length you desire.

Setting Up Killer B™ For Use

Step 1 - INSTALL STAKE INTO GROUND

Install stake into ground with foot peg facing towards the front of the decoy, toward direction of pulling line. This will keep the decoy from tipping over when pulling the line towards you.

Diagram 3 Description: Depicts a hunter using the Killer B decoy in the field. The decoy is set up with the pull line attached, and the hunter is holding the line.

Diagram 4 Description: Compares correct and incorrect stake placement. The correct setup shows the foot peg facing the front of the decoy. The incorrect setup shows the foot peg facing the back of the decoy.

Step 2 - Attach 90' Pull Line to O-Ring

Attach 90' Pull Line to O-Ring on front of decoy above beard.

Diagram 5 Description: Shows the 90' pull string attached to the O-Ring on the front of the decoy.

Installing the Mobile™ Series Real Fan Holder on Killer B™

(Large washers are used on the Fan Holder) - 1. Place washer onto bolt. 2. Place the Fan Holder onto the bolt. 3. Place the second washer on the bolt. Hand tighten wing nut to desired tension.

Assembly of Mobile™ Series Real Fan Holder

Your first step to create your real fan using the Mobile™ Series Fan Holder is to cut the real turkey fan where the tail feathers meet the body. Take one of the fan feathers and pull straight back to remove the feather. There will be some meat on the end, scrape the meat off with a knife. If the end of the quill is too long just cut it off so the feathers will be even.

The process takes approximately 20 minutes to complete your fan. A gobbler's normal tail fan has 18 feathers. The Mobile™ Series Fan Holder utilizes 16 feathers.

Diagram Description: Illustrates the three steps for assembling the fan holder and attaching feathers. Step 1 shows placing a washer onto a bolt. Step 2 shows placing the fan holder onto the bolt. Step 3 shows placing the second washer and tightening the wing nut.

WARNING: Killer B™ is so realistic, you need to use a blaze orange safety flag when carrying him through the woods. ?