Robot Roomba® 205 DustCompactor™ User Manual

Getting Started

Follow these steps to set up your robot.

1. Remove Protective Film: Remove the protective film from the camera and the foam covers from the bumper.
2. Place Docking Station: Place the docking station on a hard, level surface against a wall. Ensure good Wi-Fi® coverage. Maintain clearances: 0.5 m (1.6 ft) from both sides, 1.5 m (5 ft) in front, and 1.5 m (5 ft) from stairs. NOTE: Do not place the station in a sunny location. The space around the station must be clear for proper docking. WARNING: To prevent the robot from falling down stairs, place the docking station at least 1.5 meters (5 ft) away from stairs.
3. Connect Docking Station: Connect the power cord to an electrical outlet. Coil the cord so it does not interfere with the robot's operation.
4. Attach Side Brush: Align the edge-sweeping brush and press down until it clicks.
5. Wake Up Robot: Place the robot in front of the docking station, then slide it towards the station and align the charging contacts. After a few minutes, you will hear a beep, indicating the unit is active. NOTE: The robot is shipped with a partially charged battery, but it is recommended to fully charge the robot's battery before the first cleaning (charge for 4 hours).
6. Download Roomba® Home App: Scan the QR code with your mobile device's camera or find the Roomba® Home app in your app store. The app will guide you through the robot's configuration. With the app, you can:
   • Control cleaning time, location, and method.
   • Create automatic cleaning schedules.
   • Set custom cleaning preferences.
   • Unlock digital features.
   • Access tips and answers to frequently asked questions.
   IMPORTANT: Before operating the robot, read the included safety information.

Robot Roomba® 205 DustCompactor™ Information

Top View

1. Bin Release Button
2. Dust Bin Lid Release Button
3. Dust Bin Port
4. Arm Control Component
5. Home Button
6. Power Button

Bottom View

7. Bumper
8. LIDAR ClearView™
9. Infrared Cliff Sensor
10. Water Tank Release Button (Combo models only)
11. Water Tank (Combo models only)
12. Carpet Sensor (Combo models only)
13. Charging Contacts
14. Height Sensors
15. Edge-Sweeping Brush
16. Wheels
17. Multi-Surface Brush
18. Brush Guard Latch
19. Brush Guard
20. Swivel Front Wheel
21. Wipe Module (Combo models only)
22. Wipe Pad (Combo models only)

Component Details

Dust Compactor™ Bin

1. Compacting Arm
2. Filter
3. Dust Bin Lid Release Button
4. Dust Bin Lid
NOTE: Due to quality control, there may be residual water in the water tank. This is normal.

Water Tank (Combo models only)

5. Water Tank Release Button
6. Electrode Plates
7. Wipe Pad
8. Water Tank Plug

Docking Station

9. Infrared Window
10. Charging Contacts
11. Power Socket
12. Power Cord Socket
13. Cord Holder
14. Plug
NOTE: The Dust Compactor™ bin must be installed for both vacuuming and vacuum-mopping modes. Otherwise, the vacuum-mop robot cannot be turned on.

Charging

Power Button Indicator

Solid White Light: Robot is fully charged and connected.
Flashing White Light: Returning to docking station to charge.
Pulsing White Light: Charging in progress (low battery). If the user attempts to start a cleaning cycle, buttons will flash red and an audible alarm will sound, indicating the cycle cannot start due to low battery.
Flashing Red Light: Low battery / error.

Charging During Cleaning

The robot will return to the dock when it requires charging. Once sufficiently charged, the robot will resume cleaning where it left off.

Standby Mode

When on the docking station, the robot consumes minimal power. If the robot is not in use, you can switch it to power-saving mode by pressing and holding the [power-symbol] button for 10 seconds. To exit low power mode, briefly press the [power-symbol] button.

Robot Storage

To prepare the robot for long-term storage, turn it off by removing it from the docking station and pressing and holding the [power-symbol] button for 10 seconds. Store the robot in a cool, dry place.

Cleaning

Buttons

• HOME Button: Press to send the robot to the docking station. Press during cleaning to pause. Press after pausing to send the robot to the docking station. Press while docking to stop the unit.
• POWER Button: Press to start/pause/resume cleaning. Press and hold for 3 seconds to turn on the device. Press and hold for 10 seconds to turn off the device.

Cleaning Pattern

The robot will automatically scan and clean your home in straight lines. The robot will return to the docking station after completing a cleaning cycle, or when it needs to recharge.

Tips:

• Before cleaning, remove any clutter from the floor.
• To maintain clean floors, frequent use of the robot is recommended.

After 90 minutes of inactivity outside the docking station, the robot will automatically end cleaning. If you are unsure whether the robot has finished or is paused, check its status in the Roomba® Home app.

Spot Cleaning

Double-tap the [power-symbol] button to initiate spot cleaning of a designated area. After spot cleaning, the robot will end the cleaning cycle. Press the [home-symbol] button to send the robot back to the docking station.

NOTE: Using the Roomba® Home app for cleaning control is highly recommended. The mobile app can be used to clean specific rooms, schedule cleaning cycles, and create automations/schedules.

NOTE: Roomba robots are generally designed for vacuuming most floor types. We do not recommend using the mopping function on unsealed hardwood floors and certain laminate/vinyl panels due to the risk of water damage to the floor or subfloor. More information can be found at global.irobot.com.

Self-Emptying

1. If the Dust Compactor™ bin is full, empty it before starting cleaning.
2. Remove the water tank and wipe pad by pressing the tank release buttons on both sides of the robot.
3. To start cleaning, place the robot back on the docking station and use the app or press the [power-symbol] button.

IMPORTANT: Regular cleaning of the Dust Compactor™ bin can prevent debris buildup. Otherwise, the performance of the vacuum-mop robot may decrease.

Vacuuming and Mopping (Combo models only)

When the water tank and wipe pad are installed, the robot can vacuum and mop simultaneously. After installing the water tank and wipe pad, the robot will automatically avoid carpets when in vacuum and mop or mop-only mode.

IMPORTANT: Do not add liquids such as hot water, detergent, or disinfectant, as they may damage the robot. Use only cold water or an iRobot-approved cleaning solution, as instructed on the support page at global.irobot.com.

After completing a mopping and vacuuming clean, remember to empty the water tank and replace the wipe pad.

1. Slide the wipe pad into the water tank slot, then firmly attach it to the hook-and-loop fastener.

Water Tank Filling (Combo models only)

1. Simultaneously press and hold both water tank release buttons, then slide the tank out from the underside of the vacuum-mop robot as shown.
2. Empty old water and rinse the tank with fresh water.
3. Before reinstalling the tank into the robot, thoroughly dry the exterior of the tank.

NOTE: When cleaning the tank with detergent, use only dish soap and rinse the tank thoroughly before reinserting it into the robot. Dish soap may damage the robot during operation.

NOTE: After mopping, immediately remove the water tank and empty any remaining water, then clean and dry the wipe pad to prevent odors and mold.

Mop Pad Cleaning

Using cold water, thoroughly wash the wipe pad and allow it to air dry.

Robot Cleaning and Maintenance

To ensure optimal robot performance, perform the following cleaning and maintenance tasks periodically. Additional instructional videos are available in the Roomba® Home app. If you notice the robot is picking up less debris from the floor, empty the dust bin and clean the filter and brushes.

*Replacement frequency may vary. Parts should be replaced when visible wear occurs. If you need replacement parts, contact iRobot Customer Care for more information.

Cleaning the Edge-Sweeping Brush

Pull to remove the edge-sweeping brush. Remove hair or debris with the cleaning tool, then reattach the brush.

IMPORTANT: It is recommended to replace the edge-sweeping brush every 3-6 months for optimal cleaning performance.

Cleaning the Multi-Surface Brush

1. Press the brush guard latches and lift to remove the guard.
2. Remove the multi-surface brush.
3. Remove hair and debris from the multi-surface brush.
4. Reinstall the multi-surface brush and brush guard onto the robot.

NOTE: More detailed instructions for cleaning the multi-surface brush can be found at global.irobot.com.

IMPORTANT: It is recommended to replace the multi-surface brush every 6-12 months for optimal cleaning performance.

Cleaning the Swivel Front Wheel

1. Pull the swivel front wheel upward to remove it.
2. Remove hair and debris from the swivel front wheel and its housing.
3. Reinstall the swivel front wheel.

IMPORTANT: If the front wheel becomes blocked by wound hair or other debris, it may scratch the floor. If the wheel does not spin freely after cleaning, contact Customer Care.

Cleaning Charging Contacts and Sensors

Wipe the charging contacts and sensors with a clean, dry cloth or a slightly damp melamine sponge.

CHARGING CONTACTS

SENSORS

IMPORTANT: Do not spray cleaning solution or water directly onto the sensors or into the sensor wells.

Emptying the Dust Compactor™ Bin and Cleaning the Filter

1. Press the Dust Compactor™ bin release button to remove it.
2. Ensure the dust bin is upright, hold it over a trash can, and press the latch to open it.
3. Empty contents into the trash can.
4. Remove the filter by squeezing the latch and pulling the filter.
5. Remove debris by tapping the filter against the side of the trash can.
6. Wipe the dust bin with a clean cloth.
7. Reinstall the filter.
8. Close the dust bin securely, engaging the latch and ensuring all sides are sealed.
9. Place the dust bin back into the robot.

IMPORTANT: Squeeze any gaps that may exist around the lid's perimeter. To ensure proper operation of the dust bin, it must be sealed correctly.

Docking Station Cleaning and Maintenance

To ensure the docking station operates at optimal performance, follow the procedures outlined on the following pages.

*Replacement frequency may vary. Parts should be replaced when visible wear occurs. If you need replacement parts, contact iRobot Customer Care for more information.

Cleaning Charging Contacts and Infrared Window

Check that the parts are not dirty. Wipe with a clean, dry cloth.

IMPORTANT: Do not spray cleaning solution or water directly onto the sensors or into the sensor wells.

Troubleshooting

Robot Troubleshooting

If a problem occurs, the robot will notify you with a voice message or audible alert. The Roomba® Home app also provides notifications and instructions to help resolve issues. If you are unsure whether the robot has finished or is paused, check its status in the Roomba® Home app.

Docking Station Troubleshooting

If the docking station is not operating as expected, check the Roomba® Home app for errors.

Factory Reset

To restore factory settings, press and hold the [power-symbol] button for 5 seconds, then (within 5 seconds) press and hold the [home-symbol] + [power-symbol] buttons for 5 seconds.

SAFETY AND BATTERY SHIPPING

WARNING: Lithium-ion batteries and products containing them are subject to strict transportation regulations. If it is necessary to return this product for service, take it with you on a trip, or in a similar situation, FOLLOW THE TRANSPORTATION GUIDELINES BELOW.

• The battery MUST be disabled before shipping.
• Disable the battery by removing the robot from the docking station and pressing and holding the [power-symbol] button for 10 seconds. Press the bumper for 10 seconds while holding the [power-symbol] button. All indicators will then turn off.
• Pack the robot to ensure safe shipping.

If you need further assistance, use the Roomba® Home app, contact Customer Care, or visit global.irobot.com.

Need Additional Support? We're Here to Help!

Download the Roomba® Home app or visit global.irobot.com for technical assistance or to contact Customer Care. If further assistance is needed, please call our Customer Care at 58 781 66 62.

iRobot Customer Care Hours in Poland: Monday to Friday: 9:00 AM – 5:00 PM

Safety Information

Refer to the safety instructions included with the robot or visit global.irobot.com.

Copyright and Trademarks

©2025 iRobot Corporation, 8 Crosby Drive, Bedford, MA 01730, USA. All rights reserved. iRobot, Roomba, DustCompactor, and Roomba Combo are registered trademarks of iRobot Corporation. Wi-Fi and the Wi-Fi logo are registered trademarks of Wi-Fi Alliance. Apple and App Store are trademarks of Apple, Inc., registered in the U.S. and other countries. Google Play is a trademark of Google LLC.

More information can be found at global.irobot.com.