Sealey - Leading Professional Tool & Workshop Equipment Supplier
Instruction Manual for SEALEY models including: VS7019 Pneumatic Transmission Oil Filling System, VS7019, Pneumatic Transmission Oil Filling System, Transmission Oil Filling System, Oil Filling System, Filling System, System
Sealey VS7019 Pneumatic Transmission Oil Filling System 10L » Product
Transmission Oil Filling System Pneumatic 10L - Anvil Tool
10L PNEUMATIC TRANSMISSION OIL FILLING SYSTEM
File Info : application/pdf, 2 Pages, 531.06KB
DocumentDocument10L PNEUMATIC TRANSMISSION OIL FILLING SYSTEM MODEL NO: VS7019 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. Refer to instructions Wear eye protection 1. SAFETY Wear protective clothing 1.1. IMPORTANT Read the instructions carefully. Be familiar with the controls and the correct use of the machine. 9 Keep these instructions in a safe accessible place. WARNING! Ensure health & safety, local authority, and general workshop practice regulations are strictly adhered to when using this equipment. 9 Familiarise yourself with product application and limitations, as well as the specific potential hazards peculiar to this product. 9 Maintain the product in good condition (use an authorised service agent). 9 Replace or repair damaged parts. Use genuine parts only. Non authorised parts will invalidate the warranty. 9 Ensure safety eye protection and protective clothing are worn when using this product. 9 Keep the work area clean, uncluttered and ensure there is adequate lighting. 9 Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes. 9 Keep children and unauthorised persons away from the working area. 9 Dispose of waste liquids in accordance with local authority regulations. 8 DO NOT use to extract corrosive fluids. 8 DO NOT dismantle, tamper with or adapt the pump for any purpose other than for which it is designed. 8 DO NOT use the unit if it has been dropped or mishandled, check the unit to ensure there is no damage. 9 Keep the pump clean and store in a safe, dry, childproof location. WARNING! DO NOT allow uncontrolled discharge of fluids thus polluting the environment. WARNING! Always pay attention to the pressure control since it's a pressurised unit. 2. INTRODUCTION Pneumatic operated oil dispensing unit with 10L capacity. Large visual measurement container will identify the amount dispensed. Supplied with a range of eight transmission fluid adaptors. Features a safety valve to stop over-pressurising. Supplied with a storage case for the adaptor to minimise oil leakage when not in use. 3. SPECIFICATION Model No: Capacity: Maximum Pressure: Nett Weight: VS7019 10L 100psi (7bar) 3.02kg 4. CONTENTS 1 6 2 7 3 8 4 5 Item 1 2 3 4 Part no. VS7009.A05 VS7009.A04 VS7009.A03 VS7009.A02 © Jack Sealey Limited Description Adaptor VW Audi Adaptor VW Audi Adaptor VW Audi Adaptor universal 5 VS7009.A01 Adaptor Ford 6 VS70090.02 Audi/VW CVT 7 VS70090.03 Audi/VW DSG 8 VS70090.01 Mercedes Original Language Version VS7019 Issue 2 16/02/24 5. OPERATION 5.1. 5.1.1. 5.2. 5.2.1. FILLING NEW FLUID Open filling cap and fill with oil to level. DO NOT overfill maximum capacity is 10L. To fill oil into the tank by vacuum. Ensure the vacuum function switch is in the vacuum position, fig.1. Insert dispensing hose into oil container. Select an appropriate adaptor for the vehicle and connect to dispensing hose. Connect compressed air to the air inlet on handle and press trigger to create the vacuum required to insert new oil into the tank. Connect air supply. FILLING TRANSMISSION FLUID Select appropriate adaptor fitting from the adaptor box required for the specific vehicle. Connect the adaptor to the dispensing hose. Unscrew fitting from end of dispensing valve assembly, fig.2. Insert required adaptor and slide dispensing valve nut (and seal) over the adaptor and tighten. Turn valve on handle to the ON position to dispense the oil into the transmission. Turn valve on handle to the OFF position to stop the oil flowing. 6. MAINTENANCE 6.1. Wipe down after use. DO NOT use solvents. fig.1 Vacuum Position Switch fig.2 ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations. NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No Liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 sales@sealey.co.uk www.sealey.co.uk © Jack Sealey Limited Original Language Version VS7019 Issue 2 16/02/24