Hoover HCS5176A Fridge Freezer
Instruction Manual
Control Panel
To access the control panel, open the top door of the fridge.
Turn the knob to switch on the appliance and set the temperature for the freezer compartment and fridge. The recommended setting is between 2 and 3. Turn the knob to "0" to turn off the appliance.
The control panel features a knob with settings from 0 (off) to 3, including a "SUPER" setting. An orange light indicates when the "SUPER" function is active, meaning the compressor is running normally. A green "ON" light indicates the unit is working, unless the knob is set to 0.
Note: Some appliances may take up to 6 minutes to start functioning after being connected to the power supply and having the temperature set.
Freezing
All freezer compartments are designed for the preservation of frozen foods. For optimal freezing when the freezer is at maximum capacity, it is recommended to remove the drawers and place food directly on the shelves.
Some models feature a specific section in the top part (refer to the quick guide). To freeze food, place it in the designated drawer, turn the thermostat clockwise to the "SUPER" position, and the orange light will illuminate (as shown in Figure 1). Freezing is complete after 24 hours. Reset the thermostat to position 2-3. The "SUPER" function automatically deactivates from the circuit board after 26 hours.
The rating plate indicates the maximum quantity of food that can be frozen.
Important: For effective air circulation, ensure there is space between food items and avoid blocking the cooling air outlets.
Defrosting
A small amount of frost or water droplets on the back of the freezer compartment during operation is normal. Ensure the water outlet is always clean. Make sure food items do not touch the back or sides of the freezer compartment.
This product is equipped with an automatic frost-free system, eliminating the need for manual defrosting.
Note: The rating plate contains essential information for contacting the Service Department in case of faults.
Important: In very warm room temperatures, the appliance may operate continuously, potentially causing a layer of frost to form on the back of the fridge compartment. In such cases, adjust the knob to lower settings (1-2).
Reversing the Opening of the Doors
Follow these instructions to reverse the door opening, depending on your product's specific insert and hinge type.
Procedure A: Door Reversal Steps
- Place the appliance on the floor or at a 45° angle to access the bottom.
- Remove the lower plinth by pulling out the 3 protective plugs and loosening the screws.
- Drill the plinth on the marked left-hand side area.
- Take off the bottom right-hand hinge by removing the screws, pin, and washers, then remove the lower door.
- Remove the caps (A and B), loosen the screws, and partially remove the panel.
- Unscrew the right hinge.
- Mark and break the left-hand slot on the panel in the insert area.
- Flip the top left-hand hinge from the accessories kit.
- Remount the hinges and doors, working from bottom to top (steps 1, 2, 3).
- Fit the panel, securing it with the screws and caps.
- To reverse the handles: remove the outer caps from the right-hand side of the doors.
- Unscrew the handles from the left-hand side, move them to the right-hand side, and position the outer caps on the left-hand side of the doors.
- Place the appliance in an upright position and wait two hours before turning it on.
Procedure B: Alternative Door Reversal Steps
- Place the appliance on the floor or at a 45° angle to access the bottom.
- Remove the lower plinth by pulling out the 3 protective plugs and loosening the screws.
- Drill the plinth on the marked left-hand side area.
- Take off the bottom right-hand hinge by removing the screws, pin, and washers, then remove the lower door.
- Remove the screws from the central hinge and remove the top door.
- Unscrew the hinge from the fridge door and mount the supplied hinge on the other side.
- Mark and break the left-hand slot on the panel in the insert area.
- For a specific panel type: remove the label and screws, then partially remove the panel.
- Remove the screws from the top right hinge, invert the position of the pin, and reassemble it on the left-hand side.
- For another panel type: break the plastic membrane and screw the hinge onto the left-hand side of the panel.
- Insert the pin into the hinge and the spacer into the insert. Reassemble the hinges and doors, working from bottom to top.
- Remove the plug from the left-hand side and insert it on the right-hand side of the central and lower inserts. Invert the bushing in the lower insert.
- Screw the panel back on and replace the outer label. Place the appliance in the upright position and wait two hours before turning it on.
- To reverse the handles: remove the outer caps from the right-hand side of the doors.
- Unscrew the handles from the left-hand side and remount them on the right-hand side of the product. Place the plugs on the left-hand side.
