Built-In Fridge-Freezer and Built-In Frost Free Fridge-Freezer

Control Panel

The thermostat control for the appliance is located inside the fridge compartment on the top right. Ensure the thermostat knob is not set to "0" for the appliance to function. Adjust the knob to set the desired temperature within the fridge compartment.

This product features automatic defrosting for the freezer compartment. It is normal to observe a small amount of frost or water droplets on the back of the fridge compartment during operation.

Always ensure the water outlet is clean. Prevent food items from touching the back or sides of the fridge compartment.

Important: In very warm room temperatures, the appliance may operate continuously, leading to frost buildup on the back of the fridge compartment. If this occurs, adjust the thermostat knob to a lower setting.

Freezing of the Freezer Compartment

Place foods to be frozen in the drawer. To prevent excessive cooling of the fridge compartment at the start of the freezing process, you may need to turn the thermostat knob back, depending on the load and room temperature. Once freezing is complete, return the thermostat knob to its usual setting. The rating plate indicates the maximum quantity of food that can be frozen.

Defrosting of the Freezer Compartment

Refrigerators with FROST FREE technology do not require manual defrosting due to their automatic ice prevention system.

For versions without FROST FREE technology, manual defrosting is recommended when the frost layer exceeds 3 mm. Set the thermostat knob to "0", open the door, and remove all food, storing it in a cool place. Leave the door open until the frost has completely melted. Dry the interior of the freezer with a sponge or cloth. Replace the food items and reset the thermostat knob to the usual values.

Note: The rating plate contains essential information for contacting the Service Department in case of faults.

Note: For optimal air circulation, maintain some space between food items. For FROST FREE models, avoid blocking the cooling air vents.

Note: To test consumption and preservation standards, remove all drawers except the bottom one.

Reversing the Opening of the Doors

Follow these steps to reverse the door opening:

1. Remove the pin and corresponding bush from the top crossbar.
2. Remove the top door.
3. Remove the central hinge and its washers.
4. Remove the bottom door.
5. Remove the pin from the bottom right-hand hinge and remount it on the bottom left-hand hinge.
6. Invert the plate cover of the cabinet mounted on the plate.
7. Reassemble the hinges and doors, working from bottom to top (1 → 2 → 3).

Installation of the Appliance in the Column

1. Fasten the provided gasket to the appliance on the side opposite the hinges.
2. Insert the appliance into the column, positioning it on the side opposite the hinges.
3. Ensure the top connecting plate of the cabinet aligns perfectly with the plate on the appliance.
4. Fasten the top part of the appliance to the cabinet using the provided screws.
5. Fasten the bottom part of the appliance using the provided screws.
6. Apply the ventilation grill.
7. Loosen the fixing screws of the central right-hand hinge.
8. Position the plate close to the column.
9. Screw the plate to the column using the provided screws.
10. Tighten the fixing screws of the central right-hand hinge.
11. Repeat the same operations for the central left-hand plate.

Coupling of the Panels of the Built-In Column to the Doors of the Appliance

The appliance includes coupling devices (drive sleds) to connect the appliance doors to the column panels.

Fasten the sled to the inner part of the built-in column panel at the desired height, approximately 20 cm from the outer edge of the door.

Open the doors of the built-in column and the fridge. Position the built-in loader into the slide and then fit it into the fridge door.

Mark the screw fixing points and drill with a 2.5 mm diameter bit.

Connect the appliance door to the cabinet panel using the sled slots as guides.

Precautions for Correct Functioning

After installation, ensure the rear of the column is positioned in contact with the wall to prevent access to the compressor compartment.

Adequate air circulation is crucial for the correct operation of the appliance, specifically for cooling the condenser located at the rear. The column must feature a rear chimney with an unobstructed upper opening and a front slot covered by a ventilation grill.

Column Lock-Picking Dimensions:

• Top and side panels: 540x50mm
• Lower panel: 380x50mm
• Bottom support: 380x37mm
• Clearance from wall: 20mm

Dimensions of the gap to be left between the column and the ceiling: 50mm