VIBIA Mayfair Mini

Safety Precautions

Before assembling and installing this product, carefully read the following:

• Before first turning on the light fitting, the battery should be fully charged using the supplied charger. Only use chargers and cables approved by VIBIA. Unauthorized chargers and cables can cause the battery to explode or cause irreparable damages.
• This lamp is for indoor use only, excluding bathrooms or any type of humid surface.
• It is recommended to read the manual before installing the lamp. Keep these instructions for future reference.
• Do not disassemble, modify, or attempt to repair this fitting. For technical assistance, contact VIBIA. Any change or modification to the light fitting can void the manufacturer's guarantee.
• All electronic products and batteries must be taken to separate waste collection points at the end of their working lives. They must not be disposed of in normal household waste. It is the user's responsibility to dispose of the equipment using a designated collection point or service for separate recycling of waste electrical and electronic equipment (WEEE) and batteries, according to local laws.

Technical Specifications

Model: 5497

Net Weight: 0.54 Kg

Light Source: 1 x LED 2.5W 5V

Certifications: IP20, CE, Bi-volt

Frequency: 50/60 Hz

Electrical Class: Class III. Electrical product with low voltage safety connection.

Protection Rating: IP20 - Product protected against solid objects as big as or bigger than 12 mm. No protection against water.

Power Type: Alternating current.

Supplied Materials

The following materials are supplied with the VIBIA Mayfair Mini:

• 1 x Driver
• 1 x Lighting fixture (lamp head and stem)

Options:

Option A: No Dimming

[Diagram showing one driver unit and one lighting fixture unit for non-dimmable setup.]

Option B: DALI & 1/10V

[Diagram showing one driver unit and one lighting fixture unit for DALI and 1-10V dimmable setup.]

Product Assembly

Option A: No Dimming

Step 3.0A: Prepare the mounting surface. A detail indicates a maximum mounting box depth of 50mm.

Step 3.1A: Drill a 20 mm hole in the mounting surface for the cable.

Step 3.2A: Insert a mounting component into the drilled hole and secure it with a screw and washer.

Step 3.3A: Continue assembling the mounting component.

Step 3.4A: Ensure the mounting component is securely fastened, with the cable passing through.

Step 3.5A: Connect the electrical wires to the driver unit.

Step 3.6A: Plug the power adapter into a wall socket.

Step 3.7A: Attach the lamp head to the top of the stem.

Option B: DALI & 1/10V

Step 3.0B: Prepare the mounting surface. A detail indicates a maximum mounting box depth of 50mm.

Step 3.1B: Drill a 20 mm hole in the mounting surface for the cable.

Step 3.2B: Insert a mounting component into the drilled hole and secure it with a screw and washer.

Step 3.3B: Continue assembling the mounting component.

Step 3.4B: Ensure the mounting component is securely fastened, with the cable passing through.

Step 3.5B: Connect the electrical wires to the driver terminals.

Step 3.6B: Close the driver enclosure.

Step 3.7B: Wiring instructions:

• 1-10V System Dimming: Connect wires to L, N, C0, C1+ terminals on the driver.
• DALI System Dimming: Connect wires to L, N, DA1, DA2 terminals on the driver.

Step 3.8B: Connect the main power cable to the driver for the DALI/1-10V system.

Step 3.9B: Continue wiring and securing the driver unit.

Step 3.10B: Finalize the driver installation and connections.

Adjustments & Maintenance

Adjustments: The lamp head can be adjusted by rotating it.

Maintenance:

• For cleaning, use a slightly damp cotton cloth.
• In case of malfunction or damage, please contact the retailer where the lamp was purchased.