MiBoxer - 2 in 1 LED Strip Controller

Product Features

The MiBoxer 2-in-1 LED Strip Controller utilizes 2.4GHz wireless technology, offering low power consumption, long signal transmission, and strong anti-interference. It features an auto-transmitting function and is suitable for controlling hotel and home lighting.

• ?️ Color temperature adjustable
• ? Dim brightness
• ? 2.4G RF wireless transmission technology
• ? Remote control distance 30m
• ? Auto transmitting
• ? Support Smartphone app control (2.4GHz gateway is needed)
• ? Support third party voice control (2.4GHz gateway is needed)

Set up output mode

Set up the correct output mode based on the feature of the lights. Setting method: Press the "SET" button continuously to switch output mode. The device will log out without operation within 3 seconds.

Output Mode Sheet

PUSH Dimming

Short press PUSH switch: Turn ON/OFF light.

Long press PUSH switch:

• Stepless dimming brightness.
• Long press and release your finger, then repeat long pressing to increase or decrease brightness.

[PUSH button]

Compatible with these 2.4G RF remote controls (Purchased separately)

The controller is compatible with various MiBoxer and Mi-Light 2.4G RF remote controls, including:

• FUT006
• FUT007
• B1 / B1-B / T1
• B2 / T2
• K1 / K1-B
• FUT087 / FUT087-B
• S1-B / S1-W / S1-G
• WL-Box1

2.4G RF Remote Control Instructions

1. Linking Code Instructions

Step 1: Power off the lights for 10 seconds, then power on again. Alternatively, short press the "SET" button once, or turn on the light via the PUSH switch.

Step 2: Within 3 seconds, short press the "I" button on the remote 3 times.

Step 3: The lights will blink 3 times slowly, indicating successful linking.

Note: If linking fails (light does not blink slowly), please repeat the steps. Lights that have already been linked cannot be linked again.

2. Unlinking Code Instructions

Step 1: Power off the lights for 10 seconds, then power on again. Alternatively, short press the "SET" button once, or turn on the light via the PUSH switch.

Step 2: Within 3 seconds, short press the "I" button on the remote 5 times.

Step 3: The lights will blink 10 times quickly, indicating successful unlinking.

Note: If unlinking fails (light does not blink quickly), please repeat the steps. Lights that have not been linked do not need to be unlinked.

3. Auto transmitting (2.4G RF remote signal)

The controller can transmit remote signals to other controllers automatically when the distance between them is up to 30 meters, effectively extending the remote control range. All lights must be linked with the same remote for this function to work.

This feature allows signal transmission between lights over a distance of 30m.

4. PWM high frequency / low frequency switching (only for remote control)

Switch to high frequency (16KHz): Press the "OFF" button once within three seconds, then press the "ON" button 5 times. Successful activation is indicated by the LED light flashing 2 times quickly.

Switch to low frequency (250Hz): Press the "ON" button once within three seconds, then press the "OFF" button 5 times. Successful activation is indicated by the LED light flashing 2 times slowly.

5. "Do Not Disturb" mode is activated and shut down (default activated)

Turn on "Do Not Disturb" mode (useful in areas with frequent power outages to save energy).

2.4G RF Remote turn on and turn off instruction

Turn on "Do Not Disturb" mode: Press the "OFF" button three times within three seconds, then press the "ON" button three times. Successful activation is indicated by the LED light flashing four times quickly.

Attention: Do not disturb mode is activated

1. When the light is OFF status (e.g., turned off via app or remote): The light will remain OFF after power is turned off and then on again. The user must turn the power off and on twice, or use the app/remote to activate the light.
2. When the light is ON status: The light will remain ON after power is turned off and then on once.

Turn off "Do Not Disturb" mode: Press the "ON" button three times within three seconds, then press the "OFF" button three times. Successful deactivation is indicated by the LED light flashing four times slowly.

Attention: The light will always be in the "ON" status if you turn the power off and on once after closing "Do Not Disturb" mode.

Attention

Please follow these important precautions:

• Please turn off the power supply before installation.
• Please ensure the input voltage matches the device requirements.
• Do not disassemble the device if you are not an expert, as it may cause damage.
• Avoid using the light in areas with large metal surfaces or strong electromagnetic waves nearby, as this can seriously affect the remote control distance.

For a video instruction on the 2.4GHz series, visit: https://miboxer.com/light/video/1pc_remote.html

[CE, UKCA, RoHS certifications] Made in China