L7 Wireless Mouse
User's Manual
Product Overview
This section provides a visual overview of the MCHOSE L7 Wireless Mouse.
The mouse features the following components:
- Type-C Port: Located at the front for charging and wired connection.
- 2.4G Mode Toggle: Switch to enable 2.4G wireless connection.
- Wired Mode: Activated when the USB cable is connected.
- DPI Switch Button: Located at the bottom to cycle through DPI levels.
- Indicator Light: Provides status information (e.g., charging, DPI level).
- The mouse body is labeled with a 'K' logo.
Connection Modes
Charging/Wired Connection
Connect the included USB cable to the Type-C port on the mouse and the USB port on your computer. The mouse is now ready for use and will charge simultaneously.
2.4G Connection
1. Switch the toggle on the mouse to the [2.4G] position.
2. Connect the USB Dongle to a USB port on your computer. The mouse is now ready for use.
Manual Pairing: If the dongle is not pre-paired, press and hold the Left, Middle, and Right buttons of the mouse simultaneously for approximately 5 seconds. The indicator light will flash, indicating pairing mode. Connect the USB dongle to the computer using the USB cable. Ensure the mouse is within 20cm of the USB dongle. The indicator light will turn off upon a successful connection.
Wireless Connection (Bluetooth)
1. Switch the toggle on the mouse to the [B] position.
2. Press and hold the Left, Middle, and Right buttons of the mouse simultaneously for approximately 3 seconds. The indicator light will flash, indicating search status.
3. On your computer, search for Bluetooth devices and pair with the device named [MCHOSE L7] or [MCHOSE L7 Pro].
The indicator light will turn off upon a successful connection.
DPI Switch
Press the [DPI Switch] button located on the bottom of the mouse to cycle through six DPI levels. DPI settings can also be adjusted via driver software.
- Level 1: Red Light - 400 DPI
- Level 2: Blue Light - 800 DPI
- Level 3: Green Light - 1600 DPI
- Level 4: Yellow Light - 3200 DPI
- Level 5: Cyan Light - 6400 DPI
- Level 6: Purple Light - 26000 DPI
Note: The L7 Ultra model features a 3950 sensor with up to 42000 DPI, indicated by a purple light.
Battery Status Indicator
The indicator light provides information about the mouse's battery status:
- Red light flashing: Charge the mouse immediately.
- Red light solid: Charging in progress.
- Green light solid: Charging completed.
Charging Instructions
⚠️ Important Charging Recommendations:
- It is recommended to charge the mouse using a computer's USB port.
- Avoid using substandard or non-compliant power adapters for charging.
- Do not use over-voltage or over-current power adapters.
- Keep the mouse away from high-temperature devices while charging.
- If the device will not be used for an extended period, turn off the power switch.
These instructions are applicable to other rechargeable MCHOSE devices such as keyboards, headphones, and speakers.
Warranty Information
MCHOSE appreciates your purchase. For any quality issues within the warranty period, please present this warranty card to facilitate comprehensive after-sales service.
| Product Items: | Customer Name: |
| Serial No.: | Contact Address: |
| Purchase Date: | TEL / E-mail: |
| Purchase Channel: | Postcode: |
FCC Compliance
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations.
This device generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this device causes harmful interference to radio or television reception (which can be determined by turning the device off and on), users are encouraged to try correcting the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for assistance.
Changes or modifications not expressly approved by the responsible party could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
