Instruction Manual for VEVOR models including: SYJ-06, SYJ-06, SYJ-06 Fitting Room, SYJ-06, Fitting Room, Room
FITTING ROOM MODEL: SYJ-06 MODEL: SYJ-06 FITTING ROOM This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product. 1 SAFETY INSTRUCTIONS WARNING: Read this material before using this product. Failure to do so may result in serious injury. Assembly precautions 1. Assemble only according to these instructions. Improper assembly may create hazards. 2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly. 3. Keep the assembly area clean and well-lit. 4. Keep bystanders out of the area during assembly. 5. Do not assemble if tired or when under the influence of alcohol, drugs or medication. 6. The product capabilities apply to properly and completely assembled products only. 7. Assemble on a flat, level, hard and smooth surface capable of safely supporting the Fitting Room. 8. If possible, you can use power tools to make assembly easier. 9. For additional information regarding the parts listed in the following pages, please refer to the Assembly Diagram of this manual. Unwrap and separate all parts in a clean work area. Use precautions 1. Do not exceed specified weight capacities. 2. Use only on a flat, level, hard, and smooth surface that can safely support a fully loaded Fitting Room. 3. Use as intended only. 4. Inspect before every use; do not use if parts are loose or damaged. SAVE THIS MANUAL 2 PARTS LIST 3 Warm reminder: 1. Assembly requires two people to do it, which will make the process smoother. 2. J and K are accessories made of fabric. During transportation, they may develop wrinkles. It would be more beautiful if they are ironed before use. 4 ASSEMBLY STEP Don't tighten the screws of Accessories A and B too much. Just tighten them to 60% of the full capacity. Assemble two sets. Take parts E and F, and assemble four sets 5 Assemble Step 1 and Step 2 together, and then tighten the screws on the accessory B. Loosen the screws on the fixing pieces at both ends of accessory C, remove the half as shown in the figure, and then insert the curtain J into the C rod. 6 According to the user's high-level requirements, after assembling step 4 onto the appropriate position of the F tube, tighten the screws. Loosen the screws on the fixing pieces at both ends of accessory G, remove the half as shown in the figure, and then fix accessory H to the G tube by means of the screws. 7 According to the user's requirements, after assembling Step 6 in the appropriate position of the F tube, tighten the screws. Place the cover K onto the shelf and tidy it up. The installation is completed. L is Velcro, which can be attached to the appropriate position according to your own needs. 8 NOTE: When installing the casters, please wear gloves to avoid scratches. PRODUCT PARAMETER Model Fabric Color Frame Color Product Size(D×W×H) Net Weight SYJ-06 White Black 990*990*2045 mm 8.76 kg * Products such as specifications, appearance, and design are subject to modification without prior notice. 9 Manufacturer: Shanghaimuxinmuyeyouxiangongsi Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN. Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730 E-CrossStu GmbH EC REP Mainzer Landstr.69, 60329 Frankfurt am Main. YH CONSULTING LIMITED. UK REP C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AXWPS 文字