Trimble GPS/GNSS Surveying Equipment Price List

Trimble 5700 Base (Art. Trimble 5700 Base)

Price: 578 605 RUB

Dual-frequency GPS receiver Trimble 5700 Base designed for fast static and kinematic (RTK) surveying. With the Recon controller, you can input point information and configure the 5700 Base receiver settings. The 5700 Base receiver supports 'stop-and-go' and continuous kinematic surveying modes. The measurement delay of the 5700 Base receiver is only 0.02 s, allowing for measurements on the move. Data is recorded on a Compact Flash memory card. Data can be downloaded via USB or by simply copying from the memory card using a Card Reader. The Trimble 5700 Base can be upgraded to RTK if needed.

Technical Specifications:

• Front panel with buttons for power and data recording, CompactFlash card formatting, deletion of ephemeris and application files, and restoration of default settings.
• 24 channels for tracking C/A code and L1/L2 full cycle carrier phase.
• Magnesium alloy casing, durable and lightweight, fully sealed, meets IPX7 standard.
• Power supply from 10.5 to 28 V DC with voltage protection.
• Two removable lithium-ion batteries, 7.4 V and 2.4 Ah in internal battery compartments.
• 2 external power ports, 2 internal battery ports, 3 RS-232 serial ports, TNC connector for GPS antenna.
• Built-in USB port for data exchange at speeds over 1 Mbps.
• Operating temperature from -40°C to +65°C.
• Antenna: external, Trimble Zephyr Geodetic.

Trimble 5700 L1 (Art. Trimble 5700 L1)

Price: 262 508 RUB

Single-frequency GPS receiver Trimble 5700 L1 specially designed for fast static and kinematic (RTK) surveying. By combining the Trimble 5700 L1 GPS receiver with a Trimble Recon controller, you get an affordable single-frequency GPS system that meets all surveyor requirements. The Recon controller helps input point information and configure the 5700 L1 receiver settings. The 5700 L1 receiver supports 'stop-and-go' and continuous kinematic surveying modes. The measurement delay of the 5700 L1 receiver is only 0.02 s, allowing for measurements on the move. Data is recorded on a Compact Flash memory card. Data can be downloaded via USB or by simply copying from the memory card using a Card Reader. The Trimble 5700 L1 can be gradually upgraded, first to L1 L2 and then to RTK if needed, or all options at once. The Trimble 5700 L1 receiver does not have a built-in radio modem.

Technical Specifications:

• Front panel with buttons for power and data recording, CompactFlash card formatting, deletion of ephemeris and application files, and restoration of default settings.
• 12 channels for L1: C/A code and phase, WAAS/EGNOS.
• Expandable to 24 channels: C/A code on L1, full cycle carrier phase on L1/L2, WAAS/EGNOS.
• Magnesium alloy casing, durable and lightweight, fully sealed, meets IPX7 standard.
• Power supply from 11 to 28 V DC with voltage protection.
• 2 external power ports, 2 internal battery ports, 3 RS-232 serial ports.
• Built-in USB port for data exchange at speeds over 1 Mbps and a connector for GPS antenna.
• Over 1700 hours of continuous data recording with a 15-second interval with 6 satellites (with a 64 MB card).
• Operating temperature from -40°C to +65°C.
• Antenna frequency: TRIMBLE A3 1575.42 ±10 MHz.
• Antenna gain: min. 42 dB (amplifier plus antenna).
• Antenna connector: TNC Bulkhead.

Trimble 5700 Rover Radio (Art. Trimble 5700 Rover Radio)

Price: 633 139 RUB

Dual-frequency GPS receiver Trimble 5700 Rover Radio designed for fast static and kinematic (RTK) surveying. With the controller, you can input point information and configure the 5700 Rover Radio receiver settings. The 5700 Rover Radio receiver supports 'stop-and-go' and continuous kinematic surveying modes. The measurement delay of the 5700 Rover Radio receiver is only 0.02 s, allowing for measurements on the move. Data is recorded on a Compact Flash memory card. Data can be downloaded via USB or by simply copying from the memory card using a Card Reader. The 5700 Rover Radio model has an integrated UHF radio modem.

Technical Specifications:

• Front panel with buttons for power and data recording, CompactFlash card formatting, deletion of ephemeris and application files, and restoration of default settings.
• 24 channels for tracking C/A code and L1/L2 full cycle carrier phase.
• Magnesium alloy casing, durable and lightweight, fully sealed, meets IPX7 standard.
• Power supply from 10.5 to 28 V DC with voltage protection.
• Two removable lithium-ion batteries, 7.4 V and 2.4 Ah in internal battery compartments.
• 2 external power ports, 2 internal battery ports, 3 RS-232 serial ports, TNC connector for GPS antenna.
• Built-in USB port for data exchange at speeds over 1 Mbps.
• Operating temperature from -40°C to +65°C.
• Antenna: external, GNSS (GPS / GLONASS) antenna Zephyr 2.

Trimble NetR5 (Art. Trimble NetR5)

Price: 2 556 000 RUB

Trimble® NetR5 base station is a multi-channel, multi-frequency GNSS (Global Navigation Satellite System) receiver designed for use as a single reference station or as part of a GNSS infrastructure network. • Trimble R-Track Technology. • Advanced Trimble Maxwell Custom Survey GNSS chip. High-precision multipath correlator for pseudorange GNSS measurements. Unfiltered and unsmoothed pseudorange measurements for low noise, low multipath error, short correlation time domain, and high dynamic characteristics. GNSS carrier phase measurements with very low noise and accuracy. 1 mm in a 1 Hz bandwidth. Signal-to-noise ratio output in dB-Hz. Proven Trimble technology for tracking satellites with low elevation angles. 72 channels: GPS signals: L1 C/A code, L2C, full cycle carrier phase L1/L2/L5. GLONASS signals: L1 C/A code, L1 P code, L2 P code, full cycle carrier phase L1/L2. WAAS/EGNOS SBAS system support. Built-in 59 MB memory (1620 hours) for raw measurement data recording from 6 satellites with a 15-second interval. External memory Support for USB memory modules and USB hard drives allows recording hundreds of gigabytes of data for tasks requiring large memory capacity.

Trimble R3 (Art. Trimble R3)

Price: 204 227 RUB

Single-frequency GPS satellite receiver Trimble R3 is the best solution combining an L1 GPS receiver with an antenna, a rugged Trimble Recon PDA, and easy-to-use software. The primary application of the receiver is the creation of control and densification networks, as well as topographic surveying. The combination of the receiver and a reliable PDA proved to be a very successful solution; the Trimble R3 system can operate in extreme conditions: it is resistant to water, high temperatures, drops, and other unforeseen field conditions. The Trimble R3 receiver can track 12 channels on the L1 C/A code frequency, full cycle carrier phase L1, and can work in WAAS/EGNOS networks, providing a navigation accuracy of no more than three meters. In static and fast-static GPS surveying, the receiver provides spatial coordinate determination with a mean square error of +(5 mm + 0.5 ppm) in the plane and +(5 mm + 1 ppm) in height, and in kinematic GPS surveying, +(10 mm + 1 ppm) and +(20 mm + 1 ppm), respectively. The primary target application of this device is static observations and kinematics with subsequent post-processing.

Technical Specifications:

• 12 channels L1 C/A code, full cycle carrier phase L1, WAAS/EGNOS.
• Trimble Maxwell technology for reliable satellite tracking.
• Trimble EVEREST multipath suppression technology.
• WAAS/EGNOS differential accuracy typically less than 3 m CEP.
• Intel XScale 200 MHz or 400 MHz processor (depending on model).
• Two CompactFlash slots for memory cards and Bluetooth.
• Built-in 3800 mAh NiMH rechargeable battery.
• Expansions: 2 CompactFlash slots (one Type 1 and one Type II) with a CF-Cap O-ring for protection against rain, wind, and dust.
• Touch screen 240 x 320 pixels (1/4 VGA) color TFT.
• Connectivity: RS-232 9-pin male D-shell port, USB port.
• Operating temperature: -30°C to +60°C.
• Protection rating: IP67, meets MIL-STD-810F standard.

Trimble R6 GPS RTK Base (Art. Trimble R6 GPS RTK Base)

Price: 709 084 RUB

Dual-frequency GPS/GLONASS receiver Trimble R6 GPS RTK with integrated antenna and upgradeable to GPS/GLONASS. The primary purpose is RTK surveying and field surveys. The Trimble R6 receiver housing contains a new powerful RTK processor, which increases accuracy and work productivity. Thanks to the reception of GPS L2C and GLONASS signals, it is possible to track more satellites and perform measurements faster in challenging conditions. Trimble's tracking and positioning technology reduces downtime caused by loss of lock and re-initialization time. The Trimble R6 GPS RTK model will be supplied with the following kit: Base station kit.

Technical Specifications:

• Geodetic class Trimble Maxwell 5 GNSS chip with 72 channels.
• Simultaneously tracked satellite signals: GPS: L1C/A, L2C, L2E (Trimble L2P tracking method). GLONASS: L1C/A, L1P, L2C/A (GLONASS M only), L2P. SBAS: L1C/A.
• 3-wire serial interface (7-pin Lemo) on Port 1. Full RS-232 serial interface on Port 2 (9-pin D-sub).
• Support for external GSM/GPRS/CDPD modems for RTK surveying and VRS network operation.
• Positioning at intervals of 1 Hz, 2 Hz, 5 Hz, and 10 Hz.
• Input and output of CMR+, CMRX, RTCM 2.1, RTCM 2.3, RTCM 3.0, RTCM 3.1.
• External power input 11-28 V DC with overvoltage protection on Port 1 (7-pin Lemo).

Trimble R6 GPS RTK GSM (Art. Trimble R6 GPS RTK GSM)

Price: 746 850 RUB

Dual-frequency GPS/GLONASS receiver Trimble R6 GPS RTK GSM with integrated antenna, built-in GSM modem, and upgradeable to GPS/GLONASS. The primary purpose is RTK surveying and field surveys. The Trimble R6 receiver housing contains a new powerful RTK processor, which increases accuracy and work productivity. Thanks to the reception of GPS L2C and GLONASS signals, it is possible to track more satellites and perform measurements faster in challenging conditions. Trimble's tracking and positioning technology reduces downtime caused by loss of lock and re-initialization time. The Trimble R6 GPS RTK model will be supplied with the following kit: GSM mobile station kit, the Trimble R6 receiver has a built-in GSM modem.

Technical Specifications:

• Geodetic class Trimble Maxwell 5 GNSS chip with 72 channels.
• Simultaneously tracked satellite signals: GPS: L1C/A, L2C, L2E (Trimble L2P tracking method). GLONASS: L1C/A, L1P, L2C/A (GLONASS M only), L2P. SBAS: L1C/A.
• 3-wire serial interface (7-pin Lemo) on Port 1. Full RS-232 serial interface on Port 2 (9-pin D-sub).
• Support for external GSM/GPRS/CDPD modems for RTK surveying and VRS network operation.
• Positioning at intervals of 1 Hz, 2 Hz, 5 Hz, and 10 Hz.
• Input and output of CMR+, CMRX, RTCM 2.1, RTCM 2.3, RTCM 3.0, RTCM 3.1.
• External power input 11-28 V DC with overvoltage protection on Port 1 (7-pin Lemo).

Trimble R6 GPS RTK Radio (Art. Trimble R6 GPS RTK Radio)

Price: 746 850 RUB

Dual-frequency GPS/GLONASS receiver Trimble R6 GPS RTK Radio with integrated antenna, built-in UHF modem, and upgradeable to GPS/GLONASS. The primary purpose is RTK surveying and field surveys. The Trimble R6 receiver housing contains a new powerful RTK processor, which increases accuracy and work productivity. Thanks to the reception of GPS L2C and GLONASS signals, it is possible to track more satellites and perform measurements faster in challenging conditions. Trimble's tracking and positioning technology reduces downtime caused by loss of lock and re-initialization time. The Trimble R6 GPS RTK model will be supplied with the following kit: Base station kit, the Trimble R6 receiver has a built-in UHF modem.

Technical Specifications:

• Geodetic class Trimble Maxwell 5 GNSS chip with 72 channels.
• Simultaneously tracked satellite signals: GPS: L1C/A, L2C, L2E (Trimble L2P tracking method). GLONASS: L1C/A, L1P, L2C/A (GLONASS M only), L2P. SBAS: L1C/A.
• 3-wire serial interface (7-pin Lemo) on Port 1. Full RS-232 serial interface on Port 2 (9-pin D-sub).
• Support for external GSM/GPRS/CDPD modems for RTK surveying and VRS network operation.
• Positioning at intervals of 1 Hz, 2 Hz, 5 Hz, and 10 Hz.
• Input and output of CMR+, CMRX, RTCM 2.1, RTCM 2.3, RTCM 3.0, RTCM 3.1.
• External power input 11-28 V DC with overvoltage protection on Port 1 (7-pin Lemo).

Trimble R7 GNSS Base (Art. Trimble R7 GNSS Base)

Price: 904 511 RUB

Multi-channel multi-frequency GNSS receiver Trimble R7 GNSS Base with the latest Trimble R-Track technology allows tracking more satellites using both GPS and GLONASS. New modernized L2C and L5 signals improve the quality of the obtained solution, and are also easier to receive and process in conditions of weak signal reception. This model uses the Trimble Zephyr Geodetic 2 antenna for base station surveying to minimize the multipath effect. The Trimble R7 GNSS system is equipped with a Bluetooth module for wireless connection and more convenient user interaction with controllers, such as the Trimble TSC2.

Technical Specifications:

• GNSS (GPS / GLONASS) antenna Zephyr Geodetic 2.
• 72 channels: GPS signals: L1 C/A code, L2C, full cycle carrier phase L1/L2/L5. GLONASS signals: L1 C/A code, L10P code, L2 P code, full cycle carrier phase L1/L2.
• 4 SBAS channels: WAAS/EGNOS.
• 2 external power ports, 2 internal power ports, 3 serial ports, built-in USB port.
• Data recording to a 256 MB CompactFlash memory card with a 15-second interval: 4600 hours of GPS + GLONASS raw measurement data from 13 satellites on average. 8900 hours of GPS raw observation data from 8 satellites on average.
• External power input 10.5-28 V DC with voltage protection.
• Two removable lithium-ion batteries, 7.4 V, 2.4 Ah in internal battery compartments.
• Dust and moisture protection: IP67. Vibration meets MIL-STD-810F standard, FIG. 514.50-1.

Trimble R7 GNSS Rover (Art. Trimble R7 GNSS Rover)

Price: 838 616 RUB

Multi-channel multi-frequency GNSS receiver Trimble R7 GNSS Rover with the latest Trimble R-Track technology allows tracking more satellites using both GPS and GLONASS. New modernized L2C and L5 signals improve the quality of the obtained solution, and are also easier to receive and process in conditions of weak signal reception. This model uses the GNSS (GPS / GLONASS) Zephyr 2 antenna. The Trimble R7 GNSS system is equipped with a Bluetooth module for wireless connection and more convenient user interaction with controllers, such as the Trimble TSC2.

Technical Specifications:

• GNSS (GPS / GLONASS) antenna Zephyr 2.
• 72 channels: GPS signals: L1 C/A code, L2C, full cycle carrier phase L1/L2/L5. GLONASS signals: L1 C/A code, L10P code, L2 P code, full cycle carrier phase L1/L2.
• 4 SBAS channels: WAAS/EGNOS.
• 2 external power ports, 2 internal power ports, 3 serial ports, built-in USB port.
• Data recording to a 256 MB CompactFlash memory card with a 15-second interval: 4600 hours of GPS + GLONASS raw measurement data from 13 satellites on average. 8900 hours of GPS raw observation data from 8 satellites on average.
• External power input 10.5-28 V DC with voltage protection.
• Two removable lithium-ion batteries, 7.4 V, 2.4 Ah in internal battery compartments.
• Dust and moisture protection: IP67. Vibration meets MIL-STD-810F standard, FIG. 514.50-1.

Trimble R7 GNSS Rover w/Radio (Art. Trimble R7 GNSS Rover w/Radio)

Price: 904 511 RUB

Multi-channel multi-frequency GNSS receiver Trimble R7 GNSS Rover w/Radio with the latest Trimble R-Track technology allows tracking more satellites using both GPS and GLONASS. New modernized L2C and L5 signals improve the quality of the obtained solution, and are also easier to receive and process in conditions of weak signal reception. This model uses the GNSS (GPS / GLONASS) Zephyr 2 antenna. The Trimble R7 GNSS system is equipped with a Bluetooth module for wireless connection and more convenient user interaction with controllers, such as the Trimble TSC2.

Technical Specifications:

• Fully integrated and sealed built-in UHF radio modem.
• GNSS (GPS / GLONASS) antenna Zephyr 2.
• 72 channels: GPS signals: L1 C/A code, L2C, full cycle carrier phase L1/L2/L5. GLONASS signals: L1 C/A code, L10P code, L2 P code, full cycle carrier phase L1/L2.
• 4 SBAS channels: WAAS/EGNOS.
• 2 external power ports, 2 internal power ports, 3 serial ports, built-in USB port.
• Data recording to a 256 MB CompactFlash memory card with a 15-second interval: 4600 hours of GPS + GLONASS raw measurement data from 13 satellites on average. 8900 hours of GPS raw observation data from 8 satellites on average.
• External power input 10.5-28 V DC with voltage protection.
• Two removable lithium-ion batteries, 7.4 V, 2.4 Ah in internal battery compartments.
• Dust and moisture protection: IP67. Vibration meets MIL-STD-810F standard, FIG. 514.50-1.

Trimble R8 111 GNSS RTK (Art. Trimble R8 111 GNSS RTK)

Price: 890 771 RUB

Dual-frequency GPS/GLONASS receiver with integrated antenna Trimble R8 111 GNSS RTK is a single unit where the antenna and receiver are combined in one housing. The Trimble R8 111 receiver can be used for static and kinematic modes. When used as a rover, the receiver can be equipped with a radio or GSM modem as needed. The Bluetooth module allows for wireless data transfer and connection of external devices, such as the TSC2 or TCU controller. High degree of protection against moisture and dust, adaptation to -40°C allow this instrument to be used in the most adverse climatic conditions.

Technical Specifications:

• Simultaneously tracked satellite signals: GPS: L1C/A, L2C, L2E (Trimble L2P tracking technology), L5. GLONASS: L1C/A, L1P, L2C/A (GLONASS M only), L2P. SBAS: L1C/A, L5. Galileo GIOVE-A and GIOVE-B.
• Advanced Trimble Maxwell 6 Custom Survey GNSS chip with 220 channels.
• 3-wire serial interface on Port 1 (7-pin Lemo). Full RS-232 serial interface on Port 2 (9-pin D-sub).
• Data storage in internal memory of 57 MB: 40.7 days of raw measurement data recording (approx. 1.4 MB per day) from 14 satellites (average) with a 15-second recording interval.
• Input and output: CMR+, CMRX, RTCM 2.1, RTCM 2.3, RTCM 3.0, RTCM 3.1.
• Output of 16 NMEA messages, output in GSOF, RT17, and RT27 formats. Support for BINEX format and carrier smoothing.
• Water and dust resistance: IP67.
• Operating temperature: -40 to +65°C.

Trimble R8 111 GNSS RTK w/GSM (Art. Trimble R8 111 GNSS RTK w/GSM)

Price: 925 086 RUB

Dual-frequency GPS/GLONASS receiver with integrated antenna Trimble R8 111 GNSS RTK w/GSM is a single unit where the antenna and receiver are combined in one housing. The Trimble R8 111 receiver can be used for static and kinematic modes. When used as a rover, the receiver can be equipped with a radio or GSM modem as needed. The Trimble R8 111 GNSS RTK w/GSM includes a built-in GSM/GPRS modem for internet connection when used as a mobile receiver in the Trimble VRS network. The Bluetooth module allows for wireless data transfer and connection of external devices, such as the TSC2 or TCU controller. High degree of protection against moisture and dust, adaptation to -40°C allow this instrument to be used in the most adverse climatic conditions.

Technical Specifications:

• Fully integrated and sealed built-in GSM/GPRS modem.
• Simultaneously tracked satellite signals: GPS: L1C/A, L2C, L2E (Trimble L2P tracking technology), L5. GLONASS: L1C/A, L1P, L2C/A (GLONASS M only), L2P. SBAS: L1C/A, L5. Galileo GIOVE-A and GIOVE-B.
• Advanced Trimble Maxwell 6 Custom Survey GNSS chip with 220 channels.
• 3-wire serial interface on Port 1 (7-pin Lemo). Full RS-232 serial interface on Port 2 (9-pin D-sub).
• Data storage in internal memory of 57 MB: 40.7 days of raw measurement data recording (approx. 1.4 MB per day) from 14 satellites (average) with a 15-second recording interval.
• Input and output: CMR+, CMRX, RTCM 2.1, RTCM 2.3, RTCM 3.0, RTCM 3.1.
• Output of 16 NMEA messages, output in GSOF, RT17, and RT27 formats. Support for BINEX format and carrier smoothing.
• Water and dust resistance: IP67.
• Operating temperature: -40 to +65°C.

Trimble R8 111 GNSS RTK w/radio (Art. Trimble R8 111 GNSS RTK w/radio)

Price: 925 086 RUB

Dual-frequency GPS/GLONASS receiver with integrated antenna Trimble R8 111 GNSS RTK w/radio is a single unit where the antenna and receiver are combined in one housing. The Trimble R8 111 receiver can be used for static and kinematic modes. When used as a rover, the receiver can be equipped with a radio or GSM modem as needed. The Trimble R8 GNSS receiver is equipped with a built-in transceiver UHF radio modem, which provides exceptional flexibility when used as a mobile or base receiver. When the receiver operates as a base station, the built-in NTRIP Caster function provides configurable access to base station corrections via the Internet. The Bluetooth module allows for wireless data transfer and connection of external devices, such as the TSC2 or TCU controller. High degree of protection against moisture and dust, adaptation to -40°C allow this instrument to be used in the most adverse climatic conditions.

Technical Specifications:

• Fully integrated and sealed built-in transceiver radio modem 450 MHz: transmission power: 0.5 W. range: 3-5 km typical; 10 km under good conditions.
• Simultaneously tracked satellite signals: GPS: L1C/A, L2C, L2E (Trimble L2P tracking technology), L5. GLONASS: L1C/A, L1P, L2C/A (GLONASS M only), L2P. SBAS: L1C/A, L5. Galileo GIOVE-A and GIOVE-B.
• Advanced Trimble Maxwell 6 Custom Survey GNSS chip with 220 channels.
• 3-wire serial interface on Port 1 (7-pin Lemo). Full RS-232 serial interface on Port 2 (9-pin D-sub).
• Data storage in internal memory of 57 MB: 40.7 days of raw measurement data recording (approx. 1.4 MB per day) from 14 satellites (average) with a 15-second recording interval.
• Input and output: CMR+, CMRX, RTCM 2.1, RTCM 2.3, RTCM 3.0, RTCM 3.1.
• Output of 16 NMEA messages, output in GSOF, RT17, and RT27 formats. Support for BINEX format and carrier smoothing.
• Water and dust resistance: IP67.
• Operating temperature: -40 to +65°C.