INSTALLATION INSTRUCTIONS

⚠ CAUTIONS

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed, including:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

• DANGER

  : Risk of shock. Disconnect power before installation.

• DANGER

  : Risque de choc. Couper l'alimentation avant l'installation.

• IMPORTANT

  : This luminaire must be installed in accordance with the NEC or your local electrical code. If you are not familiar with these codes and requirements, consult a qualified electrician.

• IMPORTANT

  : Ce produit doit être installé conformément à NEC ou votre code électrique local. Si vous n'êtes pas familier avec ces codes et ces exigences, veuillez contacter un électricien qualifié.

• SUITABLE FOR WET LOCATIONS

  . CONVIENT AUX EMPLACEMENTS MOUILLÉS.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

INSTALLATION

1. Remove the lens by disengaging the (12) lens clips holding it in place. Refer to Figure 1.
2. Rotate the (4) thumb screws 90 degrees to remove the LED panel. The LED panel can be lifted away from the housing base but will be retained by plastic straps. Do NOT touch LEDs.
3. Drill out appropriate knockout(s) at the end(s) of the fixture for attachment of customer-supplied cord grip(s) or conduit connector(s).
4. Attach cord grip(s) or conduit connector(s) into holes opened in Step 3. Ensure wiring entry points are properly sealed with a high-grade caulking material, such as silicone rubber, to prevent water entry.
5. Attach the two supplied mounting brackets to the mounting surface using appropriate customer-supplied screws. Bracket spacing is 32 inches.
6. Attach one side of the fixture to both brackets by inserting the bracket bend into grooves in the housing base. Secure the fixture by snapping the other side of the fixture onto clips. A "click" should be heard when the second side of the fixture is secured.
7. Wire the fixture per the Electrical Connections section.
8. Reassemble the LED panel to the housing and secure by rotating the (4) thumb screws from Step 2. Be careful not to touch LEDs. Ensure no leads are pinched.
9. Replace the lens. Ensure the (12) plastic lens clips are properly seated when locking the lens in place.
10. Supply power to the fixture.

FIGURE 1

Diagram illustrating the fixture components: Housing base, Lens, Lens clips, and Mounting bracket grooves.

ELECTRICAL CONNECTIONS

The fixture is equipped with a universal volt driver (120-277V, i.e., 120V, 208V, 240V, or 277V).

PHASE TO NEUTRAL WIRING (120/277V)

1. Connect supply ground to fixture ground (green or green/yellow) lead.
2. Connect supply common to fixture neutral (white) lead.
3. Connect supply Vin to fixture hot (black) lead.
4. Tuck all wires carefully into the wiring chamber, ensuring no wires are pinched.

PHASE TO PHASE WIRING (208/240V)

1. Connect supply ground to fixture ground (green or green/yellow) lead.
2. Connect supply L1 (Hot) to fixture neutral (white) lead.
3. Connect supply L2 (Hot) to fixture hot (black) lead.
4. Tuck all wires carefully into the wiring chamber, ensuring no wires are pinched.

DIMMING

If 0-10V dimming is used:

• Connect the supply positive dimming lead to the violet positive fixture dimming lead. Cap off the violet dimming lead if dimming is not used.
• Connect the supply negative dimming lead to the grey or pink negative fixture dimming lead. Cap off the grey or pink dimming lead if dimming is not used.

NOTE: For dimming, use Class 1 wiring methods only.

FCC COMPLIANCE NOTICE

CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

CAN ICES-005 (A)/NMB-005 (A)