Sprayer-Spreaders for Lawn Care Applicators | Steel Green Manufacturing
Instruction Manual for STEEL GREEN models including: SG46, SG46 35 Gallon Tank Attachment, 35 Gallon Tank Attachment, Tank Attachment
File Info : application/pdf, 12 Pages, 1.94MB
DocumentDocumentINSTRUCTION MANUAL 35 GALLON TANK ATTACHMENT Models: SG46, & SG52 35 GALLON INSTALL INSTRUCTIONS STEP 1: · Disconnect the battery, ground first and then power wire. · Remove the battery from the battery box. GROUND STEP 2: Disconnect the hoses from the hopper. NOTE: Hold the hoses up to prevent oil spillage POWER 2 35 GALLON INSTALL INSTRUCTIONS STEP 3: QUICK CONNECT INSTALL NOTE: Be sure the hopper is drained before starting the following steps. · Remove the grate. · Disconnect the hopper motor hoses from the bulkhead fittings. · Remove the bulkhead fittings from the hopper. 3 35 GALLON INSTALL INSTRUCTIONS · Attach the quick couplers provided with the kit to the hopper. NOTE: Be sure the FEMALE quick connect is on the LEFT SIDE (SHOWN BLUE) and the MALE quick connect is on the RIGHT SIDE (SHOWN RED). · Reconnect the hopper motor hoses. · Reinstall the grate. 4 35 GALLON INSTALL INSTRUCTIONS · Connect the FEMALE end provided with the kit, to the end of the RIGHT SIDE hose. · Connect the MALE end provided with the kit, to the end of the LEFT SIDE hose. LEFT · Once the qd's have been attached, connect the hoses together to create hydraulic loop. RIGHT 5 35 GALLON INSTALL INSTRUCTIONS STEP 4: Disconnect the cables from the dash. DIFFUSER RATE GATE DEFLECTOR NOTE: Be sure the hopper is empty before proceeding. STEP 5: Remove the six bolts that hold the hopper assembly to the frame and lift the hopper assembly from the frame. 6 35 GALLON INSTALL INSTRUCTIONS STEP 6: · Set the 35 gallon tank assembly on the frame. · Attach it to the frame with the six bolts. VALVE ASSEMBLY VALVE ASSEMBLY W/FOAM MARKER STEP 7: Remove the (2) bolts that secure the gas tank support and Attach the valve assembly to the left side of the upright. 7 35 GALLON INSTALL INSTRUCTIONS NOTE: · Before beginning step seven, BE SURE there is no pressure on the lines and fluid is drained. · Parts removed for clarity. STEP 8: · Remove the knee pad to access the return & suction lines. · Carefully cut and install the "tee" fittings in the "suction" and "return" lines as shown (blue arrows). Securely fasten with 3/4 hose clamps. PARTS LIST ITEM QTY PART NUMBER DESCRIPTION 1 4 12HS HOSE CLAMP, 3/4 2 2 S50062 TEE FITTING, 3/4 HOSE 8 35 GALLON INSTALL INSTRUCTIONS STEP 9: · Cut and install 3/4" suction hose, connecting one end to the suction fitting on the top valve and the other end to the "tee" fitting in the suction line. · Cut and install 3/4" return hose, connecting one end to the return fitting on the bottom valve and the other end to the "tee" fitting in the return line. · Securely fasten each end with 3/4" hose clamp. SUCTION RETURN RETURN SUCTION 9 35 GALLON INSTALL INSTRUCTIONS STEP 10: Connect the "quick disconnect" hoses from the tank to the valves. · Top valve is SUCTION. · Bottom valve is RETURN. VALVE ASSEMBLY VALVE ASSEMBLY W/FOAM MARKER SUCTION RETURN 10 35 GALLON INSTALL INSTRUCTIONS STEP 11: · Set the battery in the battery box. · Reconnect the battery cables, power cable and wires first followed by the ground wire. · Attach the battery box cover and bungie strap. GROUND POWER 11 MADE IN THE USA Steel Green Mfg. 824 S State Road 39 Lebanon, IN 46052 (765)-481-2890 www.steelgreenmfg.com MANUAL PART NO. SGM-008 MANUAL REV. E DESCRIPTION 35 GALLON TANK ATTACHMENT KIT PART NO. A10034 12