OWNER'S MANUAL

Table of Contents

• Parts List
• Installation Guide
• Function Introductions
• Operating Instructions
• Disassembly Instructions
• Audio System
• Immersive Entertainment System
• Moto Sync Technology
• Setup with Wireless (Bluetooth) Connection
• Setup with SPDIF Digital Optical Cable(s)
• Setup with 3.5mm Auxiliary Audio Cable(s)
• Setup with RCA Audio Cable(s)
• Appendix
• Troubleshooting Guide

Customer Service Toll Free: 1-844-696-6886

Email: motoservice@hhcusacorp.com

Parts List

All electronics and components that need to be installed are located in bags under the foundation or attached to the frame. Before discarding the packing materials, ensure that all the parts are accounted for.

OPTIONAL EQUIPMENT (NOT INCLUDED)

Screwdriver [Icon of a screwdriver]

Installation Guide

Step 1

One person is required to set up the foundation. It takes about 5 minutes. Detach the transformer and power cord from the back rail of the mechanism under the seat. [Diagram showing a recliner with arrows indicating detachment points for transformer and power cord.]

Step 2

Slide inside back receivers onto the steel mechanism posts in the base of the recliner. Press both sides of the back firmly into place until the back automatically locks into track. Zip up the seat cushion and back cushion. [Diagram showing back receivers being slid onto posts and cushions being zipped.]

Step 3

Slide the metal inserts on the chair's wings into the metal sleeves on the side of the recliner back. [Diagram illustrating the attachment of chair wings (E) to the recliner back via metal inserts and sleeves.]

Step 4

Flip the back flap up and connect all the cables accordingly. Fasten the back flap to the bottom of the furniture. [Diagram showing cable connections for Headrest (yellow), Air Massage (purple), Lumbar (grey), Power Supply, and Heat (black).]

Step 4 (Continued)

Connect the power transformer to the socket at the bottom of the back of the recliner. Connect the Power Cord into the Power Transformer. Plug the power cord into a nearby outlet, still making sure it is clear of the metal base. [Diagram showing the sequence of connecting the power transformer and power cord to the recliner and a wall outlet.]

DONE!

Function Introductions

Caution: Read the important instructions below before operating your power mechanized equipment. Do not allow children to play on or operate this power mechanized equipment.

Side Control

[Diagram of the side control panel with buttons.]

Storage

Manual LED Hidden Cup Holder

Pull to open the hidden cup holder compartment. Push to close the hidden cup holder compartment.

Wireless Charging Tray

Press the wireless charging tray button to Turn on & Turn off the cupholder light.

USB Type-A & C Ports

[Diagram showing USB Type-A and Type-C ports.]

Cup Holder: [Illustration of the cup holder.]

Notes:

• Do not plug the power cord into a power outlet until your furniture is fully assembled and in place.
• To help prevent shock and/or damage to your product, only plug the power cord into a grounded outlet.
• Read the operating instructions carefully before operating your furniture.

Operating Instructions

Side Control Panel

[Diagram of the side control panel with labels: HEADREST, LUMBAR, CLOSE & HOME, FOOTREST, USB, Front of Arm, Type-C. Buttons labeled CLOSE/OPEN.]

To Recline:

Sit on the furniture, and press the front of the button closest to the footrest to smoothly raise the footrest and recline to any position. To lower the footrest and return to an upright position, press the back side of the button closest to the footrest.

To Adjust Headrest:

Press the front of the button closest to the backrest to smoothly raise and adjust the headrest to any position. To lower the headrest and return it to its original position, press the back side of the button closest to the backrest.

To Adjust Lumbar Support:

Press the front of the center button to smoothly raise and adjust the lumbar support to any position. To lower the lumbar support and return it to its original position, press the back side of the center button.

To Close All:

To simultaneously return the headrest, footrest, and lumbar support to their original positions, press and hold the back side of the button closest to the footrest.

Multi Media Control Panel

[Diagram of the Multi Media Control Panel with controls: Volume, Treble, Bass, Vibration, Light, Headset, Wireless Connection.]

Turning On/Off the Speaker:

Press and hold the volume adjustment knob to turn on the speaker. Press and hold again to turn off the speaker.

Wireless Connection Pairing Mode:

Press and hold the wireless button (blue light flashes) to initiate pairing. The wireless device name is: Moto Media System. Once connected, the blue light stays on and you will hear a voice prompt: "Connected." If disconnected, the blue light will turn off and you will hear a voice prompt: "Disconnected."

Switching Broadcast Mode:

1. Press the wireless button twice quickly; you will hear a voice prompt: "Broadcast mode." When connected, the red light stays on. Press the wireless button twice quickly again, and you will hear a voice prompt: "Broadcast off," which exits broadcast mode.
2. After the device connects via wireless connection, press the wireless button twice quickly (red light flashes) to enter broadcast mode; the blue light will turn purple. Press the wireless button twice quickly again to exit broadcast mode; the purple light will turn back to blue.

Using Broadcast Mode:

When a device such as a phone or TV is connected to the wireless connection of Sofa A, press the wireless button twice quickly to switch to broadcast mode (purple light stays on). Then turn on the Sofa B speaker and press the wireless button twice quickly to switch it to broadcast mode (red light stays on). Sofa A will act as the signal source, and Sofa B will sync to play the audio or video from Sofa A.

Notes on Multi Media Control Panel:

• Wireless connection search will automatically end after three minutes without connecting to any devices, and the flashing light will turn off. If you press the button during the flashing period, the search will end.
• Wireless connection mode has higher priority than broadcast mode. In broadcast mode, if different devices connect via wireless connection to play audio or video, broadcast mode will stop. If no playback occurs for about 4 seconds, it will re-search for other broadcast signal sources.
• If multiple sofas are connected to the same device via wireless connection, audio and video cannot be played simultaneously. The default is for the last connected sofa to play.
• Example: If sofas A, B, and C are all in broadcast mode (red light stays on), press and hold the wireless button (red light flashes) to connect to sofa A (purple light stays on). Sofas B and C will sync to play audio or video from sofa A. If the same device connects to sofa B (purple light flashes), sofa B and C will play normally, and sofa A will stop working. If you then connect to sofa C (purple light stays on), sofa C will play normally, while sofas A and B will not work. A restart is needed for playback.
• When using wireless connection to connect the main speaker sofa to a TV, there may be delays and instability. It is recommended to use a wired connection to the main speaker sofa and then use broadcast mode for wireless synchronization to other sofas.
• Please keep the wireless connection between devices within 10 meters.

Multimedia Control Box

[Diagram of the Multimedia Control Box with ports: POWER, SPEAKERS, INPUT (SPDIF, AUX), OUTPUT (AUX).]

This box is located at the bottom of the back of the recliner. AUX input, AUX output, and S/PDIF are located on the Multimedia Control Box. You can connect multiple devices by using a 3.5mm AUX cable connecting the AUX input to the audio source and then connecting another 3.5mm AUX cable from AUX output to the AUX input of the next Multimedia control box. 3.5mm AUX cable sold separately.

Armrest Control

Your recliner is equipped with easily accessible armrest controls for air bladder massage and heat.

[Diagram of the Armrest Control panel with buttons: AIR MASSAGE BUTTON, HEAT BUTTON, POWER BUTTON.]

POWER BUTTON:

Press the power button to turn the armrest control features on and off.

HEAT BUTTON:

Press the heat button to activate the heat function. Press again to cycle intensity through low, medium, and high heat.

AIR MASSAGE BUTTON:

Press the air massage button to activate the gentle pressure massage function. Press again to cycle through low, medium, and high intensity.

Disassembly Instructions

Unzip the seat cushion and back cushion to remove the back from the base. Pull out the black tab by hand or use a screwdriver pressing outward on the black tab, then lift the back from the recliner of the chair to release.

Screwdriver required (not included) [Diagram showing how to unzip the back cushion and a callout for a required screwdriver.]

SERIAL LABEL

Your serial number label is at the rear of the recliner, as shown in the picture. [Diagrams showing the location of the serial label on the rear of the recliner.]

FCC INSTRUCTION

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Audio System

PAIRING INSTRUCTION

Before you start: Switch on the pairing function on your mobile device. Make sure your power foundation is correctly connected and is power-on.

1. Pair with Audio System: Search for the audio device named "Moto Audio" on your device and establish a connection.
2. Music Playback: Once your devices are successfully connected, you can begin playing music through the audio system integrated into the power foundation.
3. Connection Range: Keep in mind that the effective range between the power foundation and your device is approximately 26 ft.

TROUBLESHOOTING

PRODUCT PROTECTED BY FOLLOWING PATENTS: Patented Articulating Power Headrest & Lumbar US Patent: 10, 736, 423

00982A

Thank You

Thank you for purchasing a Power Foundation.

Contact Customer Service Toll Free at 1-844-696-6886

Email: motoservice@hhcusacorp.com

Immersive Entertainment System with Sync Technology

MOTO MOTION FASHION-FORWARD FURNITURE

Congratulations on your new MotoMotion Immersive Entertainment Product(s)!

You can connect to your audio source in 4 ways:

• Wireless (Bluetooth): Easily connect at the press of a button.
• SPDIF Digital Optical Cable: (sold separately)
• 3.5 mm Auxiliary Audio Cable: (sold separately)
• RCA to 3.5 mm Auxiliary Audio Cable: (sold separately)

Though this product can be wirelessly connected to your audio source, if you would like to connect using cables, please ensure you have the necessary cables prior to your product arriving. A convenient cable kit is available for purchase at MotoMotion.

Before your product arrives, please ensure you have the necessary cables or equipment to set it up.

[QR Code placeholder]

Website: www.motomotionfurniture.com

[CONFIDENTIAL notice]

Introducing Moto Sync Technology

Experience seamless audio with Moto Sync Technology. This innovative feature wirelessly broadcasts audio signals between all MotoMotion Entertainment product(s) equipped with the technology in the closeby area, eliminating the need for cables. Enjoy a clutter-free setup and immersive sound throughout your space.

It is suggested that one piece of your Immersive Entertainment products is connected by a cable to the audio source and then connect all other Immersive Entertainment products to the cabled/connected piece by Bluetooth.

How to Identify if Your MotoMotion Immersive Entertainment Product Has Moto Sync Technology:

• Check for the Moto Sync label on your Moto Immersive Amplifier.
• Refer to the owner's manual of your product.

[Diagram of Moto Media Amplifier with ports: POWER, MOTOSYNC, SPEAKERS, INPUT (SPDIF, AUX), OUTPUT (AUX).]

Activating/Deactivating Broadcast Mode

To activate or deactivate Broadcast Mode, double tap the pairing button; The system will announce "Broadcast On" or "Broadcast Off" to indicate the current status.

[Diagram of Moto Media Controller with controls: Volume, Treble, Bass, Vibration, Pairing.]

LED Indicator Status:

Diagram of Different Connections

Wireless Setup:

[Diagram showing wireless connection from a smartphone to multiple Moto Media Amplifiers.]

SPDIF Setup:

[Diagram showing SPDIF connection from an audio source to multiple Moto Media Amplifiers via a splitter.]

AUX Setup:

[Diagram showing 3.5mm AUX connection from an audio source to multiple Moto Media Amplifiers.]

RCA-AUX Setup:

[Diagram showing RCA to 3.5mm AUX connection from an audio source to multiple Moto Media Amplifiers.]

Instructions: Establish connection to the audio source with one piece of furniture in one of connection options, then simply double tap the wireless pairing button on that piece to initiate "broadcast mode". Next, go to each of the other pieces and only double tap the pairing button to receive the established connection.

Setup with Wireless (Bluetooth) Connection

Step 1

Switch your Moto Immersive Amplifier to AUX mode. [Diagram showing amplifier ports: Power Input, MOTOSYNC, Speaker Port, Input Selection (SPDIF/AUX), AUX Input, AUX Output.]

Step 2

Locate the audio control panel on your MotoMotion entertainment product(s).

Sofa Drop Down Table: [Diagram showing control panel on a sofa drop-down table.]

Loveseat Inside the Console: [Diagram showing control panel inside a loveseat console.]

Recliner Inside the Arm Storage: [Diagram showing control panel inside a recliner arm storage.]

Step 3

Turn on Bluetooth on the device you want to connect.

Step 4

Hold the pairing button on the audio panel for 5 seconds until the blue light blinks. [Diagram illustrating holding the pairing button.]

Step 5

Find "Moto Media System" on your device (phone, tablet, TV, etc.) and select it to pair with the sound system. [Diagram showing the device interface to select "Moto Media System".]

Note: If using an Aux cord or Digital cable, the wireless function will connect but won't play sound.

Setup with SPDIF Digital Optical Cable(s)

To get the best audio performance, set up your system with a digital optical cable. Each MotoMotion amplifier has one SPDIF Digital Optical Input Port.

Step 1

Prepare the connection cable(s) and the digital optical splitter. The cable(s) you need for this setup is NOT included with your MotoMotion Immersive product(s) and can be purchased in a kit provided by MotoMotion. [Diagram of a Digital Audio Splitter.]

Step 2

Switch your Moto Immersive Amplifier to SPDIF mode. [Diagram showing amplifier ports: Power Output, Speaker Port, Input Selection (-SPDIF/AUX), AUX Input, AUX Output.]

Step 3

To set up a single MotoMotion Immersive product with your audio source, connect the digital optical cable to the SPDIF input port on your MotoMotion Immersive Amplifier. Then, connect the other end of the cable to the SPDIF output port on your audio source. [Diagram showing single SPDIF connection.]

Step 4

If you want to connect multiple MotoMotion Immersive products using SPDIF digital optical cables, you need to buy a digital optical splitter. Connect the digital optical splitter to your audio source and then run separate optical cables to each unit. [Diagram showing multiple SPDIF connections using a splitter.]

Setup with 3.5mm Auxiliary Audio Cable(s)

Connecting your audio devices is a breeze with 3.5mm auxiliary cables as this is the most common type for audio connections. If your device has a 3.5mm output port, you're all set - no extra hardware needed. Each MotoMotion amplifier comes equipped with both AUX IN and OUT ports, making it easy to handle both audio input and output.

Step 1

The cable(s) you need for this setup is NOT included with your MotoMotion Immersive product(s) and can be purchased in a kit provided by MotoMotion.

Step 2

Switch your Moto Immersive Amplifier to AUX mode. [Diagram showing amplifier ports: Power Output, Speaker Port, Input Selection (-SPDIF/AUX), AUX Input, AUX Output.]

Step 3

To set up a single MotoMotion Immersive product with your audio source, connect the 3.5mm auxiliary audio cable to the AUX input port on your MotoMotion Immersive Amplifier. Then, connect the other end of the cable to the AUX output port on your audio source. [Diagram showing single 3.5mm AUX connection.]

Step 4

If you want to connect multiple MotoMotion Immersive product(s) using 3.5mm auxiliary audio cables, you can easily daisy chain them. Just plug a second 3.5mm auxiliary cable into the AUX output port of the first MotoMotion product and then into the AUX input port of the next one. [Diagram showing multiple 3.5mm AUX connections in a daisy chain.]

*Daisy Chain: Refer to appendix on page 15.

Setup with RCA Audio Cable(s)

If you want to use the RCA (red and white) output from your audio source, you'll need to buy an RCA to 3.5mm AUX adapter cable before your MotoMotion Immersive product(s) arrives.

Step 1

The necessary cables for this setup are NOT included with your MotoMotion Immersive product and can be purchased in a kit provided by MotoMotion.

Step 2

Switch your Moto Immersive Amplifier to AUX mode. [Diagram showing amplifier ports: Power Output, Speaker Port, Input Selection (-SPDIF/AUX), AUX Input, AUX Output.]

Step 3

To set up a single MotoMotion Immersive product with your audio source:

• Plug one end of the 3.5mm auxiliary audio cable into the AUX input port on your MotoMotion Immersive Amplifier.
• Attach the RCA end of the adapter cable to the RCA output ports on your audio source. [Diagram showing single RCA to 3.5mm AUX connection.]

Step 4

To connect multiple MotoMotion Immersive products, first connect the RCA to 3.5mm AUX adapter to your audio source. Then, plug the 3.5mm auxiliary cable into the AUX input port on the first product. Next, plug a second 3.5mm auxiliary cable into the AUX output port of the first product and into the AUX input port of the next one. [Diagram showing multiple RCA to 3.5mm AUX connections.]

Appendix

Terminology - Daisy Chain

Daisy Chain refers to the configuration where large-scale devices are connected in a series. In this context, it means linking each MotoMotion product sequentially to the next. [Diagram illustrating the daisy chain concept with a smartphone and multiple furniture pieces connected.]

Troubleshooting Guide

General Furniture Issues