TECNO SPARK 30C 5G User Manual
Exploded Diagram Specification
| Part Number | Part Name | Part Number | Part Name |
|---|---|---|---|
| 1 | TP+LCM | 2 | FRONT COVER |
| 3 | SIDEKEY FPC | 4 | FRONT CAMERA |
| 5 | MAIN PCBA | 6 | RECEIVER |
| 7 | RM CAM CON FOAM | 8 | REAR 48M CAMERA |
| 9 | MAIN PCB HEAT FILM | 10 | LT SENSOR MYLAR |
| 11 | RUBBER LT SENSOR | 12 | MIDFRAM |
| 13 | IR FPC | 14 | BACK FLASH LED |
| 15 | FINGERPRINT | 16 | SIMCARD HOLDER |
| 17 | SILVER SCREW | 18 | BAT COVER |
| 19 | DECO | 20 | PMMA DECO |
| 21 | LENS | 22 | BLACK SCREW |
| 23 | FP FIXED MYLAR | 24 | FP FPC RIGID FOAM |
| 25 | BATTERY | 26 | EARJACK RUBBER |
| 27 | USB RUBBER | 28 | MOTOR |
| 29 | SPEAKER | 30 | COAXIAL CABLE 1 |
| 31 | COAXIAL CABLE 1 | 32 | SUB BOARD |
| 33 | SUB PCB BTB RUBBER |
Know Your Phone
This section describes the external features of the TECNO SPARK 30C 5G.
Front View:
- 1. Front camera: Located at the top center of the screen.
- 2. Volume + button: On the side of the phone.
- 3. Volume - button: On the side of the phone, below the volume + button.
- 4. Power button & side fingerprint sensor: On the side of the phone, typically below the volume buttons.
Rear View:
- Camera Module: Features multiple lenses (e.g., 48 MP SONY IMXS42).
- 5. NFC: Near Field Communication area indicated on the back.
SIM/SD Card Installation
Follow these steps to install SIM and SD cards:
- Power off your phone.
- Refer to the diagram for SIM/SD card installation. The diagram shows a SIM tray with slots labeled SIM 1, SIM 2, and SD. An arrow indicates the direction of insertion into the phone.
- Dual SIM: If dual SIM cards are supported, install them as shown in the diagram.
- Single SIM and SD Card: If a single SIM card and a single SD card are supported, install them in the direction indicated by the arrow in the diagram.
Charging the Phone
You can charge your phone using a charger or by connecting it to a computer via a USB cable (included with the phone).
Important: Use only TECNO chargers and cables. Using other chargers or cables may damage the phone and void its warranty.
The diagram shows the phone connected to a USB cable for charging, with a close-up view of the USB port.
FCC Caution
Labelling requirements.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Information to user.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the device.
Information to the user.
Note: This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and may radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception (able to be determined by turning the device off and on), the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the device and receiver.
- Connect the device to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information:
This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement. The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types:KL8hs (FCC ID:2ADYY-KL8HS) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 0.77W/kg and when properly worn on the body is 0.64W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
Software Information
HiOS runs on Android™ OS. Android is a trademark of Google LLC.
