Hama Magnetic+Glass+Display Glass Cover

Introduction

Thank you for choosing a Hama product. Please take your time to read the following instructions and information completely. Keep these instructions in a safe place for future reference. If you sell the device, please pass these operating instructions on to the new owner.

1. Explanation of Warning Symbols and Notes

Warning

This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.

Note

This symbol is used to indicate additional information or important notes.

2. Package Contents

• Glass cover with integrated magnetic frame
• Glass display protector
• Microfibre cloth

Note: The screen protector glass is shipped with a carrier film. Only remove this backing film when instructed to do so by these operating instructions.

3. Safety Notes

Warning:

• Small splinters of glass can lead to injuries if touched. Dispose of the product immediately if it is damaged or splintered during application or use.
• Only touch the damaged or splintered product on undamaged areas and the edge.
• Be very careful while doing so, thoroughly wash your hands afterwards and avoid contact with face and eyes.
• Use the product for its intended purpose only.
• Dispose of packaging material immediately according to locally applicable regulations.

4. Installation Requirements and Preparations

• Select a room with as little dust as possible to perform the installation (for instance the bathroom).
• Use a clean, level and flat surface with no cloth covering as a work surface.
• Check that the screen protector glass is positioned correctly. To check, place the protector glass on your screen and determine the correct direction for subsequent mounting. Openings for speakers, microphones, cameras, etc. must be kept free.
• Before attaching the protective glass, clean the screen as thoroughly as possible. Any contamination on the screen, for example dust, finger prints or lint will be visible after the protective glass is attached and may negatively affect the adhesion.

Note: A microfibre cloth which has been lightly moistened with lukewarm water is sufficient for the cleaning.

Warning: Do not clean using paper towels, kitchen towels or abrasive cleaning agents under any circumstances. This will scratch or damage the surface of the screen!

5. Attaching the Protector

Follow these steps carefully:

1. Remove the backing film using the pull tabs indicated from the adhesive side of the protective glass.
2. Pay attention not to bend the protective glass.
3. Do not touch any exposed areas on the adhesive side of the protective glass.
4. Place the protective glass adhesive side down onto the display. While doing so, make sure the protective glass is aligned with the outer edges of the display and that all the cutouts, such as the opening for the loudspeaker, match up.
5. If the protective glass is positioned incorrectly, you can pull it off and repeat the procedure.
6. Use a microfibre cloth to gently and uniformly smooth the protective glass on the display.
7. Smooth any remaining air bubbles from the middle outwards using a microfibre cloth.

Note: Most air bubbles will disappear after a short while, since the protector glass does not fully flatten out on the display until then. However, if these air bubbles are due to dust, repeat the mounting procedure after a thorough cleaning. Use strips of conventional clear cellophane tape to aid in application and removal without touching the adhesive side of the protector glass.

6. Mounting the Glass Cover

Warning: Magnets

• Keep bank cards or similar cards with magnetic strips away from the magnets. The data on the cards' magnetic strip could be damaged or completely deleted.
• People with pacemakers should keep away from the magnets. The magnets can negatively affect the function of the pacemaker.

Follow these steps to assemble the cover:

1. Clean your smartphone and remove any dust particles.
2. Open the glass cover at the bottom and take off the upper magnetic frame.
3. Place your smartphone into the magnetic frame with the glass back. Make sure that all controls are positioned at the corresponding openings.
4. Lay the upper magnetic frame onto your smartphone. The magnets stick together and close the glass cover automatically.

7. Warranty Disclaimer

Hama GmbH & Co. KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.

Model Numbers

• 00188586
• 00188587
• 00188588
• 00188589
• 00188590
• 00188591
• 00188765
• 00188776
• 00195390
• 00196760
• 00196761
• 00188817
• 00196743