METOD Assembly Instructions

Important Safety Information

WARNING!

Serious or fatal crushing injuries can occur from furniture falling down. To prevent this furniture from falling down, it must be used with the wall attachment device(s) provided.

Screws and plugs for the wall are not included. Assess the suitability of the wall to ensure that it will withstand the forces generated. Use screws and plugs suitable for your walls and the intended load. If you are uncertain, seek professional advice. Read and follow each step of the instruction carefully.

This safety warning is provided in multiple languages throughout this document.

Parts Included

• 12x Dowel (Part 101351)
• 12x Cam Lock (Part 112996)
• 6x Cam Lock Screw (Part 10046940)
• 4x Screw (Part 319503)
• 6x Cam Lock (Part 113434)
• 6x Screw for Cam Lock (Part 101351)
• 2x Wall Bracket (Part 124526)
• 2x Bracket (Part 10036383)
• 2x Bracket (Part 10039201)
• 1x Bag of Nails (Part 103693)
• 2x Wall Bracket (Part 10049278)
• 2x Wall Bracket (Part 124518)
• 2x Wall Bracket (Part 124519)
• 2x Wall Bracket (Part 10035574)
• 2x Wall Bracket (Part 103693)
• 2x Wall Bracket (Part 10039571)

Tools Required

• Phillips head screwdriver
• Flat head screwdriver
• Hammer
• Clamp

Assembly Instructions

1. Step 1: Insert twelve (12x) cam lock screws (part 10046940) into the designated holes on the cabinet panels.
2. Step 2: Attach the side panels to the base panel. Insert twelve (12x) dowels (part 101351) and twelve (12x) cam locks (part 112996). Two (2x) internal support brackets (part 10049278) are also shown being attached.
3. Step 3: Insert six (6x) dowels (part 101351) into the base panel. Attach the side panels to the base panel using these dowels.
4. Step 4: Prepare the back panel by inserting six (6x) screws (part 101351) into its edge. Then, insert six (6x) cam locks (part 113434) into the side panels and secure the back panel by tightening these cam locks.
5. Step 5: Slide the back panel into the grooves provided on the side and base panels.
6. Step 6: Insert six (6x) dowels (part 101351) into the top panel. Attach the top panel to the assembled cabinet structure by aligning it with the dowels and securing it.
7. Step 7: Secure the base of the cabinet. Insert six (6x) cam locks (part 113434) into the base panel and tighten them with screws.
8. Step 8: Rotate the assembled cabinet 90 degrees. Secure the back panel to the top edge of the cabinet using one (1x) nail (part 319503). A diagram shows the correct placement and a crossed-out image for incorrect placement.
9. Step 9: Secure the back panel to the bottom edge of the cabinet using one (1x) nail (part 319503). A diagram shows the correct placement and a crossed-out image for incorrect placement.
10. Step 10: Slide a shelf or divider into the cabinet.
11. Step 11: Attach two (2x) brackets (parts 10036383/10039201) to the top panel using eight (8x) screws (part 319503).
12. Step 12: Attach two (2x) brackets (parts 10036383/10039201) to the top panel using two (2x) screws (part 319503).
13. Step 13: Position the assembled cabinet against a wall rail system. A warning symbol is displayed, indicating the importance of secure wall mounting. An incorrect mounting example is shown with a cross symbol.
14. Step 14: Attach two (2x) wall brackets (part 124526) to the cabinet. An incorrect orientation of the bracket is shown with a cross symbol.
15. Step 15: Attach two (2x) wall brackets (part 10035574) to the cabinet. A warning symbol is displayed.
16. Step 16: Attach two (2x) wall brackets (part 103693) to the cabinet, sliding them into place.
17. Step 17: Attach two (2x) wall brackets (parts 124518/124519) to the cabinet.
18. Step 18: Attach two (2x) wall brackets (part 10039571) to the cabinet.
19. Step 19: Attach two (2x) wall brackets (part 10035574) to the cabinet. A warning symbol is displayed.
20. Step 20: Attach two (2x) wall brackets (part 103693) to the cabinet, sliding them into place.
21. Step 21: Attach two (2x) wall brackets (part 10035574) to the cabinet. A warning symbol is displayed.
22. Step 22: Attach two (2x) wall brackets (parts 124518/124519) to the cabinet.