Important Safety Information
WARNING
WARNING: Illustration shows a refrigerator with its door open and a person inside. This indicates a potential hazard requiring caution. [warning-symbol]
CAUTION
CAUTION: Illustration depicts a refrigerator being loaded into a vehicle, accompanied by a warning symbol. This signifies the need for careful handling and transport procedures. [caution-symbol]
NOTICE
NOTICE: Illustration shows a refrigerator tipping over, marked with a warning symbol. This emphasizes the importance of ensuring the unit is placed on a stable, level surface. [notice-symbol]
NOTICE
NOTICE: Diagram illustrates the refrigerator in an 'OFF' state, with a timer indicating '4 h', a water droplet symbol, and a power plug. This describes a specific operational state or a procedure involving a time delay. [notice-symbol] [power-off-symbol] [4-hour-timer] [water-droplet-symbol] [power-plug-symbol]
NOTICE
NOTICE: Illustration shows a refrigerator being loaded into a vehicle, with a red cross symbol overlaying it. This indicates an incorrect or prohibited method of loading or handling. [notice-symbol] [cross-symbol]
Basic Operation
Powering On/Off
For models RCD10.5ES, RCD10.5XES, RCD10.5ET, RCD10.5XET:
Press and hold the power button for approximately 2 seconds to turn the refrigerator ON or OFF. [power-button-icon] [2-second-duration]
Operation Modes
Control Panel Overview
Models RCD10.5ES, RCD10.5XES:
Control panel display shows 'MODE' selection and temperature settings: MIN, MID, MAX. [mode-selection] [min-setting] [mid-setting] [max-setting]
Models RCD10.5ET, RCD10.5XET:
Control panel display shows 'MODE' selection and temperature settings: MIN, MID, MAX. [mode-selection] [min-setting] [mid-setting] [max-setting]
User Interface Flow
The refrigerator offers different operational modes accessible via the user interface:
- User Mode: Select the primary operating mode. [user-mode-icon]
- Settings: Access configuration options. [settings-icon]
- Within Settings, users can select modes such as:
- Performance: For maximum cooling efficiency. [performance-icon]
- Quiet: For reduced noise operation. [quiet-icon]
- Boost: For rapid cooling. [boost-icon]
Diagram illustrates the flow from 'User mode' to 'Settings', and then to specific modes like 'Performance', 'Quiet', and 'Boost'.
Cooling Capacity
Temperature Settings
Models RCD10.5ES, RCD10.5XES:
Diagrams illustrate the MIN, MID, and MAX cooling settings available. [min-setting] [mid-setting] [max-setting]
Models RCD10.5ET, RCD10.5XET:
Diagrams illustrate the MIN, MID, and MAX cooling settings available. [min-setting] [mid-setting] [max-setting]
Shelves
Shelf Installation and Adjustment
Step-by-step instructions (1 through 6) are provided for installing and adjusting the shelves within the refrigerator compartment. This involves aligning the shelf supports and placing the shelves correctly.
[step 1] [step 2] [step 3] [step 4] [step 5] [step 6]
VG Fresh Base
Installation
Diagrams (1 through 3) show the procedure for inserting the VG Fresh Base drawer into the refrigerator.
[step 1] [step 2] [step 3]
Removal
Diagrams (1 through 3) show the procedure for removing the VG Fresh Base drawer from the refrigerator.
[step 1] [step 2] [step 3]
Defrosting
Initiating Defrost
For models RCD10.5ES, RCD10.5XES and RCD10.5ET, RCD10.5XET:
Press and hold a specific button for approximately 4 seconds to initiate the defrost cycle. [power-button-icon] [4-second-duration]
Defrost Procedure
Following the initiation, the door should be opened. The defrost process typically takes 4 to 8 hours. After defrosting, clean the interior as needed. [open-door-icon] [4-to-8-hour-timer] [cleaning-icon]
Winter Mode / Storage
Preparing for Winter
Diagrams illustrate the steps (1 through 3) for preparing the refrigerator for extended periods of non-use, such as winter storage:
- Disconnect the power supply. [power-off-icon]
- Clean the interior thoroughly. [cleaning-icon]
- Leave the refrigerator door slightly ajar to prevent odors and moisture buildup. [door-ajar-icon]
The diagram shows a sequence of actions for winter preparation.
Releasing the Door
Door Removal Procedure
Diagrams (1 through 3) detail the process for releasing and removing the refrigerator door:
- Locate and operate the release latches (labeled 'a' and 'b'). [latch-release-icon]
- Follow the sequence to disengage the door. [step 2]
- Rotate the door to approximately 90 degrees to fully release it. [rotate-90-degrees-icon]
The illustration shows specific points of release and the required motion.
