Armacost Lighting LED Touch Dimmer

Item # 511220

Product Overview

Provides full brightness control of low-voltage, white LED lighting with a touch of the finger. Works with both 12V DC and 24V DC LED lighting.

Important Information

For use only with 12V DC or 24V DC low voltage single color LED lighting. Do not connect this device to 120V AC current. For dry location use only.
Use only with 12V or 24V DC constant voltage standard electronic power supplies. Not compatible with magnetic power supplies or low voltage power supplies with 12V AC output.
Suitable for RV and boat interior applications (dry location). This device can be direct wired and powered by an on-board 12V or 24V battery.
All wiring must be in accordance with national and local electrical codes, low voltage Class 2 circuit. Contact a qualified electrician if unclear.
Shorter wire leads between the power supply, dimmer switch, and LED lighting result in brighter and more consistent lighting. Do not coil excess wire.
Maintain polarity (+ to +, – to –). Failure to observe polarity or shorting wires may damage the dimmer.
Use only insulated staples or plastic ties to secure cords and wires.
Route and secure wires to prevent pinching or damage.
For wire runs inside walls, use certified CL2 or better cabling and appropriate mounting hardware.
Do not install Class 2 low voltage wiring in the same runs as AC main power. If AC and low voltage wires cross, keep them at 90-degree angles.
Maximum load: 36 watts for 12V LEDs, 72 watts for 24V LEDs.

Operation

This device functions as an on/off switch for low voltage circuits. A quick touch turns the light on/off. Touch and hold to dim up and down.

Wiring Diagram Description: Illustrates the connection flow. A standard 12V or 24V DC power supply, connected to a 120V AC source, outputs DC power. This DC input connects to the LED Touch Dimmer Receiver's input (DC in). The dimmer's output (LED out) connects to the LED lighting (e.g., LED Tape Light or LED Puck Lights). A separate sensor cable is also shown. The diagram indicates connections for DC input (+/-) from the power supply and DC output (+/-) to the LED.

Dimensions: The device has physical dimensions of approximately 11/16 inch (17 mm) in width, 15/32 inch (12 mm) in height, and 9/16 inch (14 mm) in depth. The overall length, including connected cables, is approximately 2-9/16 inches (64 mm).

Specifications

Product Specifications
Input voltage	12V-24V DC
Output current	3A
Max load with 12V lighting	36 watts
Max load with 24V lighting	72 watts
Working temp	14 to 104°F (-10 to 40°C)
Sensor cable length	3 ft.
Input cable length	4.5 ft.
Output cable length	5 in.
Country of origin	China

Installation

Ensure power is disconnected before installation.

Recessed Installation

Requires a hole diameter of 15/32 inch (12 mm). The dimmer is designed to fit into this opening.

Surface Mount Installation

The dimmer can be mounted directly onto a surface.

Warranty

2-YEAR WARRANTY

Improper installation, improper powering, abuse, or failure to use this device for its intended purpose will void the warranty. Proof of purchase is required for all returns. For questions, email support@armacostlighting.com.

	Armacost Lighting Remote Touch LED Dimmer TDAL14 Installation and Specifications Comprehensive guide to installing and using the Armacost Lighting TDAL14 Remote Touch LED Dimmer for low-voltage LED lighting. Includes features, important notes, warnings, specifications, and connection diagrams.
	Armacost RibbonFlex PRO Continuous White Outdoor LED Tape Light Installation Guide Learn how to install Armacost RibbonFlex PRO continuous white outdoor LED tape lights. This guide covers power supply selection, wiring, voltage drop, troubleshooting, and important safety information for a successful DIY lighting project.
	Armacost Lighting Wafer Thin LED Puck Light Installation and Specifications Detailed guide for installing and using Armacost Lighting's Wafer Thin LED Puck Lights. Covers practical installation, wiring, dimming compatibility, and technical specifications for these architectural-quality, component-based LED lighting systems.
	Armacost Lighting TriVue LED Puck Light Installation and Features Comprehensive guide to the Armacost Lighting TriVue LED Puck Light, covering installation, features, specifications, and compatibility with other Armacost lighting systems. Learn about surface and flush mounting, dimming options, and typical wiring configurations for this architectural-quality LED lighting.
	Armacost Lighting Slimline RGB+W Color LED Controller with RF Remote Control - Model 723422 User guide and specifications for the Armacost Lighting Slimline RGB+W Color LED Controller (Model 723422), featuring RF remote control for color, brightness, and dynamic effect adjustments.
	Armacost RibbonFlex PRO Continuous White LED Tape Light Installation Guide Learn how to install Armacost RibbonFlex PRO Continuous White LED Tape Light with this comprehensive guide. Covers planning, power supply selection, cutting, connecting, wiring, and troubleshooting.
	Armacost Lighting RibbonFlex PRO Continuous LED Tape Light Installation Guide A comprehensive guide for installing Armacost Lighting RibbonFlex PRO continuous LED tape lights. It covers essential steps like planning, selecting power supplies and controllers, wiring, using connectors, surface preparation, troubleshooting common issues, and product specifications for Tunable White and RGB+W models.
	Armacost RibbonFlex LED Accent Lighting Wattage Calculation Guide A comprehensive guide from Armacost Lighting on calculating the total wattage for RibbonFlex LED accent lighting installations, featuring detailed charts and configuration examples for various LED tape light products.