Westcott FJ200 Strobe Quick Start Guide

Included Components & Overview

Included: FJ200 Strobe, Lithium Polymer Battery, Battery Charger, Flash Tube Cover, Tilter Bracket, Metal Reflector (5"), 30 Honeycomb Grid, Diffusion and Color Gel Set, Grid & Gel Clip, USB-A to USB-C Cable, Travel Case.

FJ200 Strobe Overview:

• Accessory Mount: For attaching modifiers.
• Daylight 5W LED Modeling Lamp: Provides continuous light for composition.
• Extended Flash Tube: The primary light-emitting component.
• Accessory Release: Button to release attached accessories.
• Umbrella Receptical: Slot for mounting umbrella shafts.
• USB-C Port: For firmware updates.
• Mini Plug (Reverse Side): Connection point.
• Removable Lithium Polymer Battery: Power source.
• Locking Dial: Secures the strobe to the tilter bracket.
• Tilter Bracket: Allows mounting to light stands and adjusting angle.
• 5" Metal Reflector: Included light shaping modifier.
• LCD Display: Shows settings and status.
• Optical Sensor: For wireless triggering.
• Return Button | Modeling Lamp: Button for menu navigation and controlling the modeling lamp.
• Control Dial/Select Button: For adjusting settings and confirming selections.
• Power ON/OFF | Test Button: Powers the unit on/off and fires a test flash.

LCD Display & Menus

The LCD displays various settings including Mode (Manual 'M' or TTL), Sync Function (Normal, HSS, Freeze*), Channel, Group, Wireless Mode, and RT ID#. The main display shows the power output value in Manual Mode or Flash Exposure Compensation in TTL Mode. Icons indicate Audible Beep, Optical Sensor, Modeling Lamp, Auto settings, and Battery Indicator.

Settings Menu:

Available Settings: Optical, Beep, TTL->M, Auto-Off, Screen, Factory Reset.

*Freeze function is available in Manual Mode only.

Introduction

This guide covers the setup, controls, and basic operation of the FJ200 Strobe. For the complete user manual, visit fjwestcott.com/4740 and navigate to the Support section.

Warning

• The flash tube, LED modeling lamp, and certain components can become hot during operation. Use caution to avoid burns.
• Use only the Westcott FJ200 Lithium Polymer Battery or the AC Power Adapter and Cord (sold separately).
• Avoid touching hot components immediately after use.
• Keep out of reach of children and pets.
• Keep away from fire, water, and moisture. Do not submerge in water.
• Avoid drastic temperature changes.
• Do not touch the flash tube or LED modeling lamp directly when replacing the flash tube.
• Remove the battery during travel/storage to prevent accidental operation.
• Do not overtighten tilter bracket tension knobs.
• Ensure the FJ200 is securely mounted before use.
• Use only compatible FJ200 modifiers and accessories, ensuring they are securely attached.
• Do not attempt to modify Westcott products. Contact Westcott for assistance.
• Maximum operating temperature: 14-104°F (-10-40°C).

Dual-Stage Heat Protection

The FJ200 has a self-monitoring system for safe operation. If the internal temperature reaches:

• 131°F (55°C) (Stage 1): A red Bulb Icon appears on the screen, and recycle time increases to 2 seconds to aid cooling.
• 167°F (75°C) (Stage 2): A red OH icon appears, and the unit becomes inoperable for approximately 10 minutes until it cools sufficiently.

The OH icon will disappear once the unit is cool and ready for operation.

Getting Started

Charging the FJ200 Lithium Polymer Battery

1. Ensure the FJ200 is OFF.
2. Remove the battery from the FJ200 by sliding the release and pulling the battery away.
3. Connect the FJ200 Charger Power Cord to the charger and plug into a wall outlet. Wait for the AC Power LED to turn red and battery LEDs to turn green.
4. Align the battery's gold contacts with the charger pins and insert the battery until it locks.
5. The battery is fully charged when all four battery LED indicators are full and stop blinking.
6. Remove the battery from the charger.

Battery Charger LED Indicator Light Colors:

• Solid Red & Solid Green: Charger ready (no battery) or battery fully charged.
• Solid Red & Blinking Green: Battery is charging.

Attaching the FJ200 Lithium Polymer Battery

Align the battery's metal contacts with the pins inside the FJ200 battery compartment. Slide the battery release towards the rear and press the battery in until it clicks.

DC Power Operation

1. Ensure the FJ200 battery is fully charged and inserted.
2. Turn the strobe ON by pressing and holding the Power | Test button until the start-up screen appears.

AC Power Operation

AC operation requires the FJ200 AC Adapter (SKU#4749), sold separately.

1. Ensure the FJ200 strobe is OFF and the battery is removed.
2. Insert the 2-pin power cord into the FJ200 AC Adapter.
3. Align the AC Adapter's metal contacts with the pins inside the battery compartment and press it in until it clicks.
4. Plug the 2-prong connector into a standard wall outlet.
5. Turn the strobe ON by pressing and holding the Power | Test button until the start-up screen appears.

Mounting

Mounting to a Light Stand

1. Attach the tilter bracket to the FJ200's base using the 1/4"-20 thread on the locking dial. Ensure the curved side of the bracket faces forward.
2. Rotate the locking dial clockwise to secure the bracket to the strobe (do not overtighten).
3. Rotate the tilter bracket's tension knob counterclockwise to position the light stand receptacle perpendicular to the strobe. Retighten by turning the knob clockwise.
4. Loosen the lower tension knob on the tilter bracket.
5. Insert the light stand spigot into the FJ200's 5/8"-16 mm tilter bracket receptacle.
6. Tighten the tension knob to secure the strobe to the light stand (do not overtighten).

Attaching & Removing Modifiers

Connecting the FJ200 Metal Reflector & Compatible Modifiers

1. Remove the FJ200's Flash Tube Cover by sliding the adapter release, rotating the cover counterclockwise, and pulling it away.
2. Align the four square mounting blocks of the FJ200 Metal Reflector (or compatible modifier) with the openings on the strobe's face.
3. Insert and rotate the modifier clockwise until it locks into place.

Removing the FJ200 Metal Reflector & Modifiers

1. Ensure the strobe is OFF and has cooled for five minutes.
2. Carefully grasp the modifier.
3. Slide the strobe's adapter release away from the modifier.
4. Rotate the modifier counterclockwise until its mounting blocks align with the adapter openings, then gently pull the modifier away.

Attaching an Umbrella-Based Modifier

1. Ensure the strobe is OFF and has cooled for five minutes.
2. Slide the umbrella's shaft into the strobe's umbrella receptacle on the tilter bracket.
3. Slide the umbrella to the desired position.

Note: The FJ200's tilter bracket does not have an umbrella tension screw. Avoid tilting the strobe at angles that could cause the umbrella to slide out and potentially cause damage.

Removing an Umbrella Based Modifier

1. Ensure the strobe is OFF and has cooled for five minutes.
2. Grasp the umbrella's shaft and gently slide it out of the FJ200 umbrella receptacle.

Note: Never force attachment or removal. Use caution when removing modifiers to avoid damaging the flash tube. Umbrella shafts larger than 8mm may not fit the receptacle.

Updating Firmware

The FJ200 features a USB-C port for firmware updates only. Updates can enhance performance and modify menu options. Visit fjwestcott.com/4740 to check for the latest firmware.

Installing the Firmware

1. Visit fjwestcott.com/4740, go to the Support section, and download the latest firmware ZIP file. If your browser automatically unzips it, proceed to Step 3.
2. Unzip the file and open the extracted folder.
3. Read all files in the extracted folder (e.g., README, Changelog).
4. Ensure the FJ200 is OFF and cooled before removing the battery.
5. Connect the USB-A to USB-C cable to the FJ200's USB-C port.
6. Your computer should recognize the FJ200 as an external drive.
7. Locate the .BIN file on your computer and drag it to the FJ200 drive. Only the .BIN file should be copied.
8. Once the file copy is complete, EJECT the FJ200 from your computer.
9. Remove the USB-C cable and reinsert the battery.
10. Press and hold the Power | Test button on the FJ200 to initiate the firmware update. Confirm installation by checking for the firmware version text in the bottom right corner of the screen during startup.

IMPORTANT

• Complete firmware updates with at least 50% computer battery power. Power loss during the update can render the FJ200 inoperable.
• Always eject the FJ200 from your computer before removing the USB cable to prevent potential damage.
• If copying issues occur, try closing the progress window and retrying, or restart your computer.

Warranty

F.J. Westcott Co. warrants the FJ200 against defects in materials and workmanship for ONE (1) YEAR from the original retail purchase date. Westcott will repair or exchange the product if a defect arises within the warranty period, at its discretion.

This warranty does not cover:

• Damage from accident, abuse, misuse, flood, fire, earthquake, mold, or other external causes.
• Damage from operating the product outside its intended use.
• Products or parts modified without Westcott's written permission.
• Cosmetic damage like scratches or dents.

Disclaimer: By using this product, the customer accepts full responsibility and releases Westcott and its associates from any liability related to manufacturer defects, malfunctions, or misuse that may lead to injury or unforeseen complications. Westcott is not responsible for damages resulting from improper mounting, hanging, or storage, including damage to equipment, property, personal injury, death, fire damage, or any other unmentioned damages.

To request warranty service, contact Westcott Customer Support for a Return Authorization Number (RMA). The RMA must be clearly marked on the outside of the shipping box. Items sent without pre-authorization or not covered under warranty will be returned at the sender's expense.

Contact Information:

• Phone: 800-886-1689 / 419-243-7311 (International)
• Email: support@fjwestcott.com
• Shipping Address: F.J. Westcott Co, 1425-B Holland Rd. Maumee, OH 43537

Register your new gear online at FJWESTCOTT.COM/REGISTER.

Visit WESTCOTTU.COM for videos, pro tips, inspiration, and more.

Westcott products are manufactured to high standards and comply with safety regulations. Product modifications may occur. Made in China. ©F.J. Westcott Co. All rights reserved.