Ariston Slideout Hood User Manual

Hello

Congratulations on selecting this Ariston slideout rangehood. Our appliances have been specifically designed for Australian and New Zealand kitchens. Please read through this user manual carefully as it contains information that will ensure that your appliance is installed correctly, important operating & care instructions, and also some advice on what to do if this appliance is not performing as intended.

Warning & Safety Information

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Young children should be supervised to ensure that they do not play with the appliance.
• There shall be adequate ventilation of the room when the rangehood is used at the same time as appliances burning gas or other fuels.
• You must read the details concerning the method and frequency of cleaning. There is a fire risk if cleaning is not carried out in accordance with the instructions.
• Do not flambé under the rangehood.
• Exhaust air must not be discharged into an existing flue which is used for exhausting fumes from appliances burning gas or other fuels.
• The minimum distance between the hob surface and the lowest part of the rangehood is 600mm. This distance shall be at least 650mm if the rangehood is installed over a gas hob. If the instructions for the gas hob specify a greater distance, this has to be taken into account.
• Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air are fulfilled.
• If the supply cord of this equipment is damaged, it must only be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
• This appliance has been designed for indoor domestic use only.
• Do not remove or inspect the filters whilst the hood is in operation.

Installation & Ducting

Figure 1.1 shows a diagram of the rangehood with dimensions and indicates a 10A plug fitted.

Figure 1.2 illustrates the minimum height from the hob surface to the underside of the rangehood. For an electric hob, this is 600mm, and for a gas hob, it is 650mm.

Important: Before handling the rangehood during installation, it is recommended that you remove the filter to prevent damage.

Notice: If the instructions for the gas hob specify a greater distance, this has to be observed. Any installation above 750mm will compromise performance.

Ducted Option

1. Remove the filter.
2. Optional: Replace the 40mm front rail with the 80mm front rail (included in the box).
3. Ensure the internal switch is in the ducted position.
4. Determine the most efficient path for the ductwork, minimize bends, and keep the length of the ductwork to a minimum.
5. Before fixing the range hood, drill a hole to accommodate the 120mm ducting that you have selected.
6. It is important to run and finish (install roof/wall caps) prior to installation of the hood.
7. Ensure that access has been allowed for the power cable and plug after installation.
8. Remove the 120mm ducting cover plate and attach the ducting adaptor.
9. Hold the hood up to the underside of the cabinet. Screw the rangehood to the underside of the cabinet. Ensure that you do not damage any of the wiring during installation.
10. Attach the ducting adaptor to the ducting.
11. Re-install filter.
12. Plug in the power to the unit, turn on and test.

Re-Circulating Option

1. Remove the filter.
2. Remove the front sealing tape to expose the front vents. Do not remove the top 120mm outlet cover.
3. Ensure the internal switch is in the recirculating position.
4. Drill 4 fixing holes as per the drawing. Ensure that access has been allowed for the power cable and plug.
5. Hold the hood up to the underside of the cabinet. Screw the rangehood to the underside of the cabinet. Ensure that you do not damage any of the wiring during installation.
6. Re-install filter.
7. Plug in the power to the unit, turn on and test.

Notice: When the rangehood is re-circulating, carbon filters should be installed.

Warning: DO NOT penetrate any screws into the range hood as this may result in electrical hazards.

Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

Diagrams show 'Top Ducting', 'Side Ducting', and 'Front Re-Circulating' (Carbon filter required) options.

Operating Instructions

Important: To operate the unit, ensure that the power is turned on and the front visor is fully extended. This will provide access to the light and speed controls.

Fan Speed

The LOW/OFF/HIGH switch is located on the right-hand side of the unit. This unit features 2 speed settings. A single line indicates low speed, and double lines indicate the high speed.

To turn the unit off, you can either slide the visor into the closed position or set the speed switch to the middle position (off).

Light

The On/Off switch for the light is located on the left-hand side of the unit, as indicated in the diagram.

Diagram shows controls for 'LIGHT' and 'LOW/OFF/HIGH' fan speed.

Maintaining Your Rangehood

General Maintenance

Ensure that the power to the unit is switched off prior to cleaning. The surface should only be cleaned with warm soapy water and a soft non-abrasive cloth. In coastal environments and humid areas, more frequent cleaning is required to maintain the finish.

Filters

This unit is supplied with Aluminium filters designed for ducted installations. Aluminium filters are dishwasher safe or can be cleaned with hot soapy water. Ensure that filters are thoroughly dry before re-installing.

You may want to order charcoal filters designed to eliminate odours from the exhaust fumes when installing the appliance for recirculating mode. These filters cannot be cleaned and should be replaced every 3-6 months depending on use.

Lamps

Your range hood is fitted with one of the following two different types of lamps accordingly to its model:

• Model ARHS60X: 40W Halogen GU10 (x2)
• Model ARHS60X-L: 3W LED GU10 (x2)

Product Specification

600 SLIDEOUT HOOD

Model: ARHS60X

• 220-240V ~ 50HZ
• Total: 280W
• Lights: 2 x 40W Max
• Motor: 2 x 100W
• Manufactured for Arisit Pty Ltd
• Made in PRC

Model: ARHS60X-L

• 220-240V ~ 50HZ
• Total: 206W
• Lights: 2 x 3W
• Motor: 2 x 100W
• Manufactured for Arisit Pty Ltd
• Made in PRC

For service please call:

• Australia: 1300 815 589
• New Zealand: 09 306 1020

Symbols indicate compliance with CE standards and electrical safety.

Proof of Purchase

Attach your proof of purchase here for future reference.

Notes

Space for user notes.

Contact Details

AUSTRALIA

ARISIT PTY LIMITED
40-44 Mark Anthony Drive
Dandenong South, VIC 3175
Australia
Ph: 1300 815 589
FX: (03) 9768 0838
consumer.care@arisit.com

NEW ZEALAND

ARISIT PTY LIMITED
PO Box 68-140
Newton, Auckland 1145
New Zealand
Ph: (09) 306 1020
FX: (09) 302 0077
sales@aristonappliances.co.nz

Ariston is committed to ongoing research and development. Every effort has been made to ensure all information in this user manual is correct at the time of going to print. Dimensions should be used as a reference only, and actual dimensions should be taken from the physical product only. The manufacturer reserves the right to change specifications without notice.