GE Profile™ PTD60GBSR/BPR 7.4 cu. ft. Capacity Aluminized Alloy Drum Gas Dryer with Sanitize Cycle and Sensor Dry

Model Numbers: PTD60GBSRWS (White), PTD60GBPRDG (Diamond Gray)

DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)

Exhaust Option

The dryer offers 3-way exhaust capability via the rear, left, and bottom. It is shipped with rear exhaust, and alternate exhausting knockouts are supplied.

Gas Requirements

Requires an individual, properly-grounded branch circuit with a three-prong grounding-type receptacle, protected by a 15 or 20 amp circuit breaker or a time-delay fuse.

Gas Dryer Electric Rating

120V, 60Hz, 7A

Gas Input (BTU/HR)

22,000 BTU/HR. Factory-equipped for natural gas. Tested for LP gas; LP gas supply requires a conversion kit. Consult installation instructions for the correct kit and have a qualified gas technician install it. Refer to dryer ducting information for proper installation.

? NOTE: The dryer wall outlet must be located within 36 inches of the service cord entry and be accessible when the dryer is mounted.

General Installation Information

For complete installation details, refer to the installation instructions packed with your dryer.

? ALCOVE OR CLOSET INSTALLATION REQUIREMENTS

Dryer approval for alcove or closet installation will be stated on a label on the dryer back.
The dryer MUST be exhausted to the outside.
Minimum clearances between the dryer cabinet and adjacent walls or other surfaces are: 0 inches on both sides, 0 inches at the rear, and 1 inch at the top.
Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 square inches of open area, equally distributed. If the closet contains both a washer and a dryer, doors must contain a minimum of 120 square inches of open area, equally distributed.
No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

?️ BATHROOM OR BEDROOM INSTALLATION REQUIREMENTS

The dryer MUST be exhausted to the outdoors.
Installation must conform with local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.

MINIMUM CLEARANCES (OTHER THAN ALCOVE OR CLOSET INSTALLATION)

Minimum clearances to combustible surfaces are: 0 inches on both sides; 1 inch at the rear.

? DRYER EXHAUSTING INFORMATION

Use metal duct only, for both vertical and horizontal ducting.

Diagrams and Dimensions

Side View Diagram: Shows the dryer's side profile. Key dimensions are: Overall width 23-1/4 inches. Overall height 43-7/8 inches. Depth to the front panel is 28-1/4 inches, and depth to the door is 28-7/8 inches. The height of the door opening is 38-1/2 inches. From the side, the base extends 8 inches. The front edge of the base is 3-7/8 inches from the front panel, and the bottom edge of the base is 3-1/4 inches from the floor. The top panel extends 30-1/2 inches to the front panel and 31-1/8 inches to the door.

Rear View Diagram: Illustrates the dryer's rear profile. Key dimensions are: Overall width 27 inches. Depth to the front panel is 11-3/4 inches. The power cord extends 5-1/2 inches. The diagram indicates the location of the power cord hole.

Power Cord Locations (Back View) Diagram: Depicts the back of the dryer, highlighting the power cord hole. A measurement '5' is noted at the top. The power cord hole is positioned approximately 4-1/2 inches from the right side and 5 inches from the bottom edge.

DUCTING MATERIALS AND EXHAUST LENGTH CALCULATION

FOR COMPLETE INFORMATION, SEE INSTALLATION INSTRUCTIONS PACKED WITH YOUR DRYER.

Ducting Materials

For optimal performance, use 4-inch diameter all rigid metal exhaust duct. If rigid metal duct is not feasible, UL-listed flexible metal (semi-rigid) ducting (Kit WX08X10077) can be used. In specific installations, connecting to the house vent may require a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct is permissible ONLY where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4-inch diameter can be maintained throughout the entire transition duct length. Consult your dryer's installation instructions for complete details when using flexible metal (foil type) ducting.

Exhaust Length Calculation

Determine the number of 90° turns required for your installation. Add one turn if exhausting to the side or bottom of the dryer.
The maximum length of 4-inch rigid (aluminum or galvanized) duct that can be tolerated is detailed in the table below. A turn of 45° or less may be disregarded. Two 45° turns within the duct length should be counted as one 90° elbow. Any turn over 45° should be treated as a 90° elbow.

Dryers must be exhausted to the outside.

⚠️ CAUTION: For personal safety, do not terminate exhaust into a chimney, under an enclosed house floor (crawl space), or into an attic, as accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, as the combination of lint and grease could create a fire hazard.

Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts and bird nesting. The wall cap must also be located at least 12 inches above the ground or any other obstruction, with the opening pointed downwards.

For more information on venting kits and accessories, please call 1-800-GE-CARES.

? DRYER EXHAUSTING INFORMATION - USE METAL DUCT ONLY (VERTICAL AND HORIZONTAL DUModels: PTD60GBSRWS, PTD60GBSR-BPR, PTD60GBSR 7.4 cu. ft. Capacity Gas Dryer, PTD60GBSR, 7.4 cu. ft. Capacity Gas Dryer, Capacity Gas Dryer, Gas Dryer
Google Docs
Google Drive
Download [pdf]
Download Optimized
Document:
References

File Info : application/pdf, 4 Pages, 432.07KB
Document Document

xzhkwajeteir0wuleejd

References

GE Appliances: Shop for Home, Kitchen, & Laundry Appliances

Adobe InDesign 16.2 (Macintosh) Adobe PDF Library 15.0

Related Documents

	GE Profile PTD60GBSR/BPR 7.4 cu. ft. Gas Dryer: Dimensions, Installation, Features, and Specifications Comprehensive guide for the GE Profile PTD60GBSR/BPR 7.4 cu. ft. capacity gas dryer, detailing dimensions, installation requirements, venting specifications, and key features like Sanitize Cycle and Sensor Dry. Includes model numbers PTD60GBSRWS and PTD60GBPRDG.
	GE Profile PTD60GBSR/BPR 7.4 cu. ft. Gas Dryer: Features, Installation, and Specifications Comprehensive guide to the GE Profile PTD60GBSR/BPR 7.4 cu. ft. aluminized alloy drum gas dryer, detailing installation requirements, dimensions, venting guidelines, features like Sanitize Cycle and Sensor Dry, and smart capabilities via SmartHQ.
	GE Profile PTD60GBSR/BPR Gas Dryer: Features, Dimensions & Installation Guide Explore the GE Profile PTD60GBSR/BPR 7.4 cu. ft. gas dryer. Learn about its features like Sensor Dry, Sanitize Cycle, Wi-Fi connectivity, dimensions, and essential installation requirements including venting and clearances.
	GE VTD56GASVWB 7.4 cu. ft. Multipay Gas Dryer - Features and Specifications Discover the GE VTD56GASVWB, a 7.4 cu. ft. commercial multipay gas dryer with an aluminized alloy drum. Learn about its payment options, warranty, Launderday™ app, SmartHQ™ management, commercial-grade components, Microban® protection, and detailed specifications.
	GE Appliances Dryer Installation Guide Comprehensive installation instructions for GE Appliances dryers, covering electrical and gas connections, venting requirements, and safety precautions. Ensure proper setup for optimal performance and safety.
	GE GFD35ESPYDS 7.8 cu. ft. Smart Front Load Electric Dryer with Quick Dry - Specifications & Installation Detailed specifications, dimensions, installation requirements, features, and accessories for the GE GFD35ESPYDS 7.8 cu. ft. Smart Front Load Electric Dryer with Quick Dry. Includes venting information and warranty details.
	GE Profile PFD95ESPTDS Smart Front Load Electric Dryer Specifications Detailed specifications for the GE Profile PFD95ESPTDS, a 7.8 cu. ft. capacity smart front load electric dryer with Steam and Sanitize Cycle. Includes dimensions, installation requirements, electrical ratings, and features.
	GE VTD56EASVWB 7.4 cu. ft. Commercial Multipay Electric Dryer Discover the GE VTD56EASVWB, a 7.4 cu. ft. commercial electric dryer featuring aluminized alloy drum, multipay options including QR code payment and coindrop, SmartHQ™ Management, Microban® Protection, and a 5-year parts-limited warranty. Learn about its key features and specifications.