Installation Guide for HD Ridez models including: WB-CN295MD, WB-CN295BD, WB-CN295MD Drop Down Boards Side Step, WB-CN295MD, Drop Down Boards Side Step, Down Boards Side Step, Boards Side Step, Side Step
HD Ridez Drop Down Boards Side Step Compatible with Silverado Sierra 1500 2019-2024 Extended Cab & 2500 3500 2020-2024 (Exclude 19 1500 LD)(Silverado 1500 LTD Sierra 1500 LD 2022) : Automotive
INSTALLATION INSTRUCTIONS NB1 RUNNING BOARDS 19-24 Chevy Silverado/GMC Sierra 1500 Double Cab (Incl. Diesel models with DEF tanks, 2022 Silverado 1500 LTD and 2022 Sierra 1500 Limited) (Excl. 19-21 Silverado 1500 LD & 19-21 Sierra 1500 Limited) (Rocker Panel Mount), 20-24 Chevy Silverado/GMC Sierra 2500/3500 Double Cab (Incl. Diesel models with DEF tanks) (Rocker Panel Mount) PART # WB-CN295MD /WB-CN295BD NB1 RUNNING BOARDS 19-24 Chevy Silverado/GMC Sierra 1500 Double Cab (Incl. Diesel models with DEF tanks, 2022 Silverado 1500 LTD and 2022 Sierra 1500 Limited) (Excl. 19-21 Silverado 1500 LD & 19-21 Sierra 1500 Limited) (Rocker Panel Mount), 20-24 Chevy Silverado/GMC Sierra 2500/3500 Double Cab (Incl. Diesel models with DEF tanks) (Rocker Panel Mount) PARTS LIST: 1 Driver/left side NB1 Running Board 32 10mm x 27mm x 3mm Flat Washers 1 Passenger/right side NB1 Running Board 16 10mm Nylon Lock Nuts 4 Driver/left side Mounting Brackets 16 8-1.25mm x 30mm Hex Bolts 4 Passenger/right side Mounting Brackets 16 8mm Lock Washers 16 10-1.5mm x 35mm Hex Bolts 16 8mm x 24mm x 2mm Flat Washers (4) Passenger/right Mounting Brackets (4) Driver/left Mounting Brackets Passenger/Right Running Board Front PROCEDURE: REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED. 1. Start the installation under the passenger/right side of the vehicle. Locate the 6 plugs along the bottom edge of the body. Mounting Brackets will bolt to the 1st, 3rd, 4th and 6th threaded mounting holes, (Figure 1). Remove the plastic plugs from each mounting location. Directly above each threaded insert is a top mounting location on the side of the body panel, (Figure 2). Hold a Bracket up in place to help determine the correct mounting holes to use along the body. NOTE: Thread an 8mm Hex Bolt into the threaded inserts to clear paint from hole as required. 2. Select (1) Passenger/right side Mounting Bracket. Starting at the front of the passenger/right side, bolt the Mounting Bracket to the factory threaded holes with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figures 3 & 4). Do not tighten hardware at this time. 3. Repeat Steps 1 & 2 to install the Mounting Brackets on the remaining mounting locations along the body panel, (Figures 5 & 6). 4. Carefully unwrap and select the Passenger/right side Running Board. Use the illustration above to help identify the correct Running Board. Position the mounting tabs on the Running Board to the passenger/right rear of the Mounting Brackets, (Figure 7). Page 1 of 4 02/07/19 (AL) NB1 RUNNING BOARDS 19-24 Chevy Silverado/GMC Sierra 1500 Double Cab (Incl. Diesel models with DEF tanks, 2022 Silverado 1500 LTD and 2022 Sierra 1500 Limited) (Excl. 19-21 Silverado 1500 LD & 19-21 Sierra 1500 Limited) (Rocker Panel Mount), 20-24 Chevy Silverado/GMC Sierra 2500/3500 Double Cab (Incl. Diesel models with DEF tanks) (Rocker Panel Mount) 5. Attach the Running Board to the Brackets using (8) 10mm Hex Bolts, (16) 10mm Flat Washers and (8) 10mm Nylon Lock Nuts, (Figures 8--10). Do not tighten hardware at this time. 6. Level and adjust the Running Board as necessary and fully tighten all hardware. 7. Repeat Steps 1--6 for Driver/left side Running Board installation. 8. Do periodic inspections to the installation to make sure that all hardware is secure and tight. To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used also to clean the Running Board. Passenger/Right side Installation Pictured Front (Fig 1) Driver/left side Rocker Panel mounting locations illustrated (arrows) NOTE: Hold Bracket up to body panel to help determine the correct mounting locations. Front (Fig 2) Passenger/Right front mounting location (Fig 3) Passenger/Right Front Bracket Page 2 of 4 02/07/19 (AL) NB1 RUNNING BOARDS 19-24 Chevy Silverado/GMC Sierra 1500 Double Cab (Incl. Diesel models with DEF tanks, 2022 Silverado 1500 LTD and 2022 Sierra 1500 Limited) (Excl. 19-21 Silverado 1500 LD & 19-21 Sierra 1500 Limited) (Rocker Panel Mount), 20-24 Chevy Silverado/GMC Sierra 2500/3500 Double Cab (Incl. Diesel models with DEF tanks) (Rocker Panel Mount) Passenger/Right side Installation Pictured (2) 8mm Hex Bolts (2) 8mm Lock Washers (2) 8mm Flat Washers Front (Fig 4) Mounting Bracket illustration to Body Panel Front Front (Fig 5) Passenger/Right Second Bracket (Fig 6) Passenger/Right rear Bracket (2) 10mm Hex Bolts (4) 10mm Flat Washers (2) 10mm Nylon Lock Nuts Front (Fig 7) Mounting Bracket to Running Board Page 3 of 4 02/07/19 (AL) NB1 RUNNING BOARDS 19-24 Chevy Silverado/GMC Sierra 1500 Double Cab (Incl. Diesel models with DEF tanks, 2022 Silverado 1500 LTD and 2022 Sierra 1500 Limited) (Excl. 19-21 Silverado 1500 LD & 19-21 Sierra 1500 Limited) (Rocker Panel Mount), 20-24 Chevy Silverado/GMC Sierra 2500/3500 Double Cab (Incl. Diesel models with DEF tanks) (Rocker Panel Mount) Passenger/Right side Installation Pictured Front (2) 10mm Hex Bolts (4) 10mm Flat Washers (2) 10mm Nylon Lock Nuts (2) 10mm Hex Bolts (4) 10mm Flat Washers (2) 10mm Nylon Lock Nuts (Fig 8) Passenger/Right front Complete install (2) 10mm Hex Bolts (4) 10mm Flat Washers (2) 10mm Nylon Lock Nuts Front (Fig 9) Passenger/Right complete install Front (Fig 10) Passenger/Right complete install Installation Complete Page 4 of 4 02/07/19 (AL)WPS 文字