FSP 65W Medical Adapter
FSP065 Series
FEATURES
- Compact size: 129 x 51 x 31 mm
- Certified Medical Safety: IEC 60601-1
- Meets Energy Efficiency: DOE Level VI
- No Load Power Consumption: ≤ 0.21W
- High altitude operation: 5000M
- Meets emission limits: EN55011 and FCC Class B
- Over Temperature Protection
- Available in Class-I & Class-II designs
SAFETY STANDARD APPROVAL
Certifications: [UL Certified] (E211696), [TÜV Rheinland Certified], [CE Certified]
Standards: EN 60601-1, IEC 60601-1
DESCRIPTION
The series of AC/DC switching power supplies can deliver 65 watts continuous output power. They feature high efficiency and compact dimensions with an IEC320/C8 or IEC320/C6 inlet for interchangeable cords for world-wide use. All models meet EN55011 and FCC Class B emission limits.
INPUT SPECIFICATIONS
| Input voltage: | 90-264 VAC |
|---|---|
| Input frequency: | 47-63 Hz |
| Input current: | < 1.8 A (rms) / 115 VAC < 0.9 A (rms) / 230 VAC |
| Touch current: | < 100 μA / 264 VAC, 60 Hz |
OUTPUT SPECIFICATIONS
- Output voltage/current: See rating chart
- Total output power: 65W
- Protection:
- Over voltage: The power supply will shut down while over-voltage happened.
- Short circuit: Output can be short-circuited without damage, and will recover automatically after short-circuit condition is removed.
- Over current: Output current shall be limited between 200% max load and auto recovery or latch protection.
- Over temperature: The power supply will shut down while over-temperature happened. It will shutdown operation after the fault condition is removed.
ENVIRONMENTAL SPECIFICATIONS
| Operating temperature: | 0°C~+40°C |
|---|---|
| Storage temperature: | -20°C~+85°C |
| Operating humidity: | 5~95% RH non-condensing |
| Storage humidity: | 5~95% RH non-condensing |
GENERAL SPECIFICATIONS
| Efficiency: | 87% min. |
|---|---|
| Hold-up time: | 8 ms minimum at 115Vac/60Hz |
| Line regulation: | ±1% maximum at full load |
| Inrush current: | 60 A @ 115 VAC or 140 A @ 230 VAC, at 25°C cold start |
| Operating altitude: | 5000 meters |
| Withstand voltage: | 4000 VAC from input to output (2 MOPP) |
| MTBF: | 150,000 hours at full load at 25°C ambient, calculated per MIL-HDBK-217F |
EMC Performance (IEC60601-1-2)
| Standard | Performance |
|---|---|
| EN55011: | Class B conducted, class B radiated |
| FCC: | Class B conducted, class B radiated |
| VCCI: | Class B conducted, class B radiated |
| EN61000-3-2: | Harmonic distortion, Class A |
| EN61000-3-3: | Line flicker |
| EN61000-4-2: | ESD, ±15 KV air and ±8 KV contact |
| EN61000-4-3: | Radiated immunity, 3 V/m |
| EN61000-4-4: | Fast transient/burst, ±2 KV |
| EN61000-4-5: | Surge, ±1 KV diff., ±2 KV com. |
| EN61000-4-6: | Conducted immunity, 3 Vrms |
| EN61000-4-8: | Magnetic field immunity, 3 A/m |
| EN61000-4-11: | Voltage dip immunity, 30% reduction for 500 ms, 60% reduction for 100 ms, and >95% reduction for 10 ms |
OUTPUT VOLTAGE/CURRENT RATING CHART
| Model | Class-I | Class-II | Voltage | Min. Current | Max. Current | Tolerance | Ripple & Noise | Max. Power | Average Active Efficiency (typical) @ 115/230 VAC |
|---|---|---|---|---|---|---|---|---|---|
| FSP065-DHBM1 | FSP065-DHCM1 | 12 V | 0 A | 5.42 A | ±5% | 120 mV | 65W | 87% | |
| FSP065-DBBM1 | FSP065-DBCM1 | 19 V | 0 A | 3.43 A | ±5% | 190 mV | 65W | 87% | |
| FSP065-DACM1 | 24 V | 0 A | 2.71 A | ±5% | 240 mV | 65W | 87% |
NOTES:
- Class-I models are equipped with IEC 320/C6 inlet, and Class-II models with IEC 320/C8 inlet.
- Ripple and noise measurements shall be made with an oscilloscope of at least 20MHz bandwidth. Output shall be bypassed at the connector with a 0.1μF ceramic disk capacitor and a 10μF electrolytic capacitor to simulate system loading.
MECHANICAL SPECIFICATIONS
Class I IEC 320/C6 AC Inlet
Diagram Description: This diagram shows the Class I adapter with an IEC 320/C6 AC inlet. Key dimensions include an overall length of 129±0.5 mm, width of 51±0.5 mm, and height of 30.9±0.5 mm. It features an LED indicator, mounting holes, and a cable tie wire. Specific component placement and dimensions are detailed, such as a 10.0 REF dimension and other measurements like 39.7±0.5 mm. The case color is black.
Class II IEC 320/C8 AC Inlet
Diagram Description: This diagram illustrates the Class II adapter with an IEC 320/C8 AC inlet. It shares similar overall dimensions with the Class I model: length 129±0.5 mm, width 51±0.5 mm, and height 30.9±0.5 mm. It also includes an LED indicator, mounting holes, and a cable tie wire. Specific component placement and dimensions are detailed, similar to the Class I version. The case color is black.
NOTES:
- Dimensions shown in mm.
