Hanin Z5S Portable Photo Printer

Product Introduction

This document provides a comprehensive guide to the Hanin Z5S Portable Photo Printer, model HCP-2TS25F.

Front View:

Features include a flash, shutter button, view frame, and paper outlet.

Rear View:

Includes the supplies inlet cover.

Top View:

Features a power button/shutter button view frame and paper outlet.

Bottom View:

Includes a filter switch knob and a Type-C interface.

Inner Components:

The printer contains an LED indicator and a lanyard hole.

Product Parameters

Accessories:

The package typically includes a Quick Start Guide, Consumable, USB Cable, and Lanyard. Note that package contents may vary based on the order.

Consumable Installation Instructions

1. Open the supplies inlet cover.
2. Insert the consumable into the compartment, pressing at the "PUSH HERE" position until it clicks into place.
3. Close the supplies inlet cover.

Printing Instructions

1. Power-on: Long press the power button until the LED indicator lights up.
2. Adjust Filter: Rotate the filter switch knob to select different filter effects.
3. Turn on Flash: Short press the flash button to toggle the flash on/off. The LED indicator is blue when the flash is off and green when it is on.
4. Take Pictures and Print: Short press the power/shutter button to activate the shutter. Short press the view frame button to print the current shooting content.

APP Print

Scan the QR code to download the "HeyPhoto" APP.

1. Open the APP and click "Add device".
2. Search for "Z5S-XXXX" and click to connect.
3. In the app, select the photos you want to print and edit them as needed before printing.
4. After the first connection, the printer will automatically connect when you click the print icon.

Do not exit the APP during the printing process, as this may cause printing failure. APP interface may change with versions; refer to the actual interface.

Precautions

• The photo paper is sensitive to moisture; use it promptly after opening.
• Only use official photo paper with the ribbon; do not replace it independently.
• Avoid excessive direct sunlight and low temperatures.
• Do not force a damaged or deformed ink cassette into the device.
• The optimal working temperature for the printer is 5°C~35°C. High ambient temperatures may affect print quality.
• Use official ribbon and photo paper for best results.
• Avoid disassembling the ribbon and photo paper. Contamination of the photo paper's glossy surface will affect print quality.
• Do not forcibly pull out the consumable during printing to prevent damage to the printer.
• When not in use for extended periods, close the consumable compartment to prevent dust ingress.
• After printing multiple photos consecutively, the device may activate overtemperature protection, which is normal. The task will continue after cooling.
• Do not operate the device while it is turning on.

Function Button Operation Instructions

Filter Operation Instructions

Rotate the knob to select filter effects for photo printing:

• PATPAT
• MARK
• FOREVER
• AUTOFOCUS
• Blue
• R (Red)
• A (Art)
• V (Vivid)
• Original

Note: Each filter is designed for specific scenarios; incorrect filter choices may lead to suboptimal shooting and printing outcomes.

Operating Environment

• Place the printer on a desktop or other flat, stable surface.
• Ensure there is more than 10cm of space at the paper outlet of the printer.

Battery Charging

• When the battery power is low, charge it using the equipped USB cable. Continued printing may cause the device to power off automatically.
• Connect one end of the USB cable to the printer's port and the other end to a power adapter. The printer enters a charging state, interrupting printing.
• Charging takes approximately 90 to 120 minutes. Check the charging status via the indicator light.
• The printer can be charged via a computer or a USB adapter. The adapter is not included. Ensure any purchased power adapter is certified for safety and meets standard requirements.
• Do not disassemble the machine. Replacing the battery with an incorrect model may cause an explosion. Dispose of used batteries according to instructions.
• When the printer is low on power, charge it for a while before use to prevent printing interruptions.

FCC WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC ID: 2AUTE-2TS25F

FC CE

Compatibility

This device is compatible with a wide range of Apple devices including various models of iPhone, iPad, and iPod touch. The "Made for Apple badge" indicates that the accessory is designed to connect specifically to Apple products and meets Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.

Apple, iPad, iPad Air, iPad Pro, and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries and regions. The trademark "iPhone" is used in Japan with a license from Aiphone K.K.