Amazon Basics 30m Hose Reel Cart

1. Important Safety Instructions

Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included.

When using the product, basic safety precautions should always be followed to reduce the risk of injury, including:

• WARNING: Risk of electric shock! Do not aim the water jet at electrical appliances, equipment, or outdoor power sockets.
• CAUTION: Risk of injury! Do not aim the water jet at persons or animals.
• CAUTION: Risk of damage to the water inlet! Use only the included inlet hose. Do not use other solid or rigid piping.
• Keep the work area clean and dry. Damp or wet work areas can result in injury.
• Keep children away from the work area. Do not allow children to handle this product.
• Do not modify this product, and do not use it for a purpose for which it was not intended.
• Before using, carefully check that the product operates properly and performs its intended function. Check for damaged parts and any other conditions that may affect operation. Replace damaged or worn parts immediately.
• Do not overreach. Keep proper footing and balance at all times to prevent tripping, falling, or back injury.
• Do not use the product when tired or under the influence of drugs, alcohol, or medication. A moment of inattention may result in personal injury.
• Ensure the product is properly assembled and installed before connecting input and output hoses.
• Before each use, check that the hose is not obstructed. During use, stay aware of the hose to prevent kinks, being run over, or blocking by other gardening equipment. Water pressure buildup can cause damage and injury.
• Ensure incoming water pressure does not exceed the rated operating pressure.
• Do not use hoses different from that for which the product is intended.
• Do not leave water running through the product unsupervised.
• Do not expose the product to freezing temperatures with water remaining in the unit.
• Turn the water off after each use.
• The product is not suitable for supplying drinking water. Ensure no water from the inlet hose gets into the drinking water supply by fitting a non-return valve or pipe interrupter between the tap and the hose inlet.
• This product is intended for private use only.

2. Before First Use

DANGER: Risk of suffocation! Keep any packaging materials away from children and pets – these materials are a potential source of danger, e.g., suffocation.

• Remove all the packing materials.
• Remove and review all components before starting assembly.
• Check the product for transport damages.

3. Product Description

The product consists of the following components:

• A Handle: The main carrying handle.
• B Locking sleeve (handle): Used to secure the handle height adjustment.
• C Supply hose: The primary hose that extends from the reel.
• D Crank handle: Used to wind the supply hose onto the reel.
• E Hose reel: The drum around which the supply hose is wound.
• F Nozzle: The attachment at the end of the supply hose for spraying water.
• G Supporting leg: A leg at the base of the cart for stability.
• H Locking sleeve (support leg): Used to secure the supporting leg length adjustment.
• I Wheels: Two wheels at the base for mobility.
• J Water inlet (with cover cap): The connection point on the cart where the inlet hose attaches.
• K Inlet hose: Connects the water source to the cart. It has a quick connector at one end and a quick connector with an adapter set (Ø12.7 mm, Ø19 mm) at the other.
• L Water inlet adapter: An adapter that attaches to the water inlet (J) on the cart.

4. Adjusting the Handle/Supporting Leg

Adjusting the Handle Height:

1. To adjust the height of the handle (A), unscrew the locking sleeves in anti-clockwise direction (turn left ?).
2. Lift or push the handle (A) down as desired, applying equal pressure on both sides.
3. After adjustment, securely fasten the locking sleeves in clockwise direction (turn right ?).

Adjusting the Supporting Leg Length:

4. To adjust the length of the supporting leg (G), unscrew the locking sleeves in anti-clockwise direction (turn left ?).
5. Push the supporting leg (G) inward or outward as desired, applying equal pressure on both sides.
6. After adjustment, securely fasten the locking sleeves in clockwise direction (turn right ?).

5. Connecting to Water Supply

CAUTION: Risk of damage! The supply line pressure must not exceed the maximum operating pressure of the product.

1. Locate the end of the inlet hose (K) with the quick connector and adapter. Pull the sleeve on the quick connector to detach the adapter set.
2. Separate the adapter set by turning the bottom sleeve anti-clockwise (turn left ?).
3. Install the adapter parts onto a suitable water tap:
   • For a 12.7 mm water tap, attach the 12.7 mm adapter first, then the 19 mm adapter.
   • For a 19 mm water tap, attach only the 19 mm adapter.
4. Unscrew the cover cap from the water inlet (J). Install the water inlet adapter (L) onto the water inlet (J).
5. Connect one end of the inlet hose (K) to the adapter on the tap, and connect the other end to the water inlet adapter (L) on the water inlet (J).

6. Use

CAUTION: Risk of damage! Avoid folding or pressing on the inlet hose (K) or supply hose (C) while water is running, which can cause high water pressure and damage the product.

• To extend: Hold the nozzle (F) and slowly pull the supply hose (C) out.
• To spray: Adjust the spray pattern by turning the tip of the nozzle (F). Turn anti-clockwise for a cone spray, or clockwise for a concentrated stream.
• To wind: Unfold the crank handle (D) and turn it anti-clockwise to roll up the supply hose (C).
• After winding, press the release button and fold the crank handle (D).
• CAUTION: Risk of injury! Be careful when folding the crank handle (D) to avoid pinching fingers.

7. Cleaning and Maintenance

7.1 Cleaning

• Wipe the product with a soft, slightly damp cloth.
• Wash and rinse the hoses (C/K) to remove any soil or heavy dirt after use. Use a plastic brush for stubborn dirt if needed. Let the hoses (C/K) air dry.
• Pull the sleeve on the quick connector of the supply hose (C) to detach the nozzle (F). To unclog the nozzle (F), insert a needle (not included) into the nozzle opening and move it back and forth.
• Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the product.

7.2 Storage

• Drain all water from the hoses (C/K).
• Store the product and its accessories in a frost-free area. Do not store the product in an area with ambient temperature below 0° C.
• Store in a cool, dry place away from children and pets, ideally in its original packaging.
• Avoid vibrations and shocks.

7.3 Maintenance

• Regularly check that all components and fasteners are tightened.
• Use soap and water when checking connections for leakage.

8. Frequently Asked Questions

9. Disposal

Dispose of the product according to local regulations. If in doubt, consult your local authorities.

10. Specifications

10.1 Importer Information

For EU: Amazon EU S.à r.l., 38 avenue John F. Kennedy, L-1855 Luxembourg. Business Reg.: 134248.

11. Feedback and Help

We would love to hear your feedback. To ensure we are providing the best customer experience possible, please consider writing a customer review.

amazon.co.uk/review/review-your-purchases#

If you need help with your Amazon Basics product, please use the website or number below.

amazon.co.uk/gp/help/customer/contact-us