Sunlite

Sale available on BulbAmerica.com. Take an additional 5% off with coupon code 5PDF.

Important: Please read and understand this entire manual before attempting to assemble, operate, or install the product.

Warning: To avoid fire or electric shock, follow installation instructions carefully. Consult a qualified electrician if unsure about electrical installation. Wear rubber-soled shoes and work on a sturdy ladder. Ground the fixture to avoid potential electric shock. Handle metal parts carefully to prevent cuts. Account for all parts and destroy all packing material to prevent hazards to children. This product is suitable for indoor applications only.

Caution: Turn off the power at the fuse or circuit breaker box before installation and maintenance.

Note: This fixture is suitable for 120-277-Volt fused circuits. Installation must comply with the National Electric Code and local building codes. Consult a qualified electrician if unsure about wiring. The fixture body is one piece; do not disassemble or make alterations.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

UL Listed

Dimmable: Compatible with most wall-based 0-10V dimming controllers.

Installation

(Mounting hardware not included)

Step 1: Prepare Fixture Ends

Unlock the two nuts located at the ends of the fixture. (Visual cue: Figure 1 shows the fixture ends with nuts.)

Step 2: Mount Fixture to Ceiling Grid

Install the fixture to the ceiling grid and securely tighten the two terminal nuts. (Visual cues: Figure 2 shows the fixture being attached to the grid, and Figure 3 shows the terminal nuts being tightened.)

Step 3: Prepare Junction Box

Unlock the nuts from both ends of the junction box. (Visual cue: Figure 4 shows the junction box with nuts to be unlocked.)

Step 4: Secure Junction Box

Secure the junction box to the fixture and tighten the two terminal nuts. (Visual cues: Figure 5 shows the junction box being attached to the fixture, and Figure 6 shows the junction box nuts being tightened.)

Step 5: Connect Driver and Junction Box

Connect the RJ45 connector from the fixture to the output connector of the junction box. Note: One driver can support a maximum of 3 units. (Visual cues: Figure 7 shows the RJ45 connector being plugged in, and Figure 8 illustrates the driver's capacity.)

Step 6: Wire Connections

Open the junction box. Connect the Live (L), Neutral (N), and Ground (G) wires using the provided 4-pin connectors. Connect the dimming wire with the orange connector cap. (Visual cue: The wiring diagram details these connections: Purple/Grey for 0-10V Dimming (+D/-D), Black for Line, White for Neutral, and Green for Ground.)

Step 7: Final Ceiling Cover

Cover the plasterboard to complete the installation, ensuring there is no opening at the ceiling. (Visual cues: Figures 9 and 10 show the final installation with the ceiling covered.)

Ceiling Grid Configuration and Installation

T-grid removal from the drop ceiling can be adjusted according to your desired shape design. Note: Adjacent T-grids must be secured by pendants.

Example Grid Layouts:

• For a "+" shape, remove T-grids No. 1, No. 2, No. 3, and No. 4.
• For a "T" shape, remove T-grids No. 1, No. 2, No. 5, and No. 6.

(Visual cue: Figure 1 provides a general diagram illustrating different ceiling grid layouts and indicating which T-grids to remove for various configurations.)

"L" Shape Installation

Step 1: For the No. 1 light fixture, fix the A-end (with wire) by pendant and the B-end onto the "a" T-Grid. (Visual cue: Figures show fixture 1 attached to a pendant and T-grid "a".)

Step 2: Fix the No. 2 light fixture onto the No. 1 light fixture using its A-end with wire, and attach the B-end to the "b" T-Grid. (Visual cue: Figures show fixture 2 attached to fixture 1 and T-grid "b".)

Additional Fixture Installation

Following the "L" shape installation method, install the No. 3 and No. 4 light fixtures similarly.

"T" Shape Installation

Step 1: Install the No. 1 light fixture, securing its A-end (with wire) onto the "d" T-Grid and the B-end by pendant. (Visual cue: Figures show fixture 1 attached to T-grid "d" and a pendant.)

Step 2: Fix the A-end (with wire) of the No. 2 light fixture onto the No. 1 light fixture, and attach the B-end of the fixture to the "e" T-Grid. (Visual cue: Figures show fixture 2 attached to fixture 1 and T-grid "e".)

Step 3: Using the same method, fix the A-end (with wire) of the No. 5 light fixture onto the "g" T-Grid, and the B-end onto the "f" T-Grid. (Visual cue: Figures show fixture 5 attached to T-grid "g" and T-grid "f".)

"+" Shape Installation

Following the "T" shape installation steps, replace the "f" T-Grid with an additional light fixture.