Patpet P-Collar682 Dog Training System - Quick Start Guide

Overview

The Patpet P-Collar682 Dog Training Collar is designed to help dogs live more harmoniously with people. This guide provides essential steps for setting up and using the product.

Setting Up the Product

Before using the Dog Training Collar, follow these setup steps:

Charging the Remote and Receiver Collar:
- Plug in and fully charge both the Remote and Receiver Collar. The initial charge requires 4 hours; subsequent charges take 2-3 hours.
- When fully charged, the red LED on the Receiver Collar will turn green.
- Note: Use a DC 5V 500-800mA charger. Avoid using chargers that do not meet specifications. Excessive charging can shorten battery life; charge only when batteries are low. Turn off the collar when not in use to extend battery life.
Prepare the Remote:
- Turning ON/OFF the Remote: Push the lock switch from 'OFF' to 'ON' to turn on the remote. The LCD will light up showing channel, battery power, and levels. Push the lock switch to 'OFF' to turn the remote off.
- Remote Components:
  - A. Lock Status Display
  - B. Battery Display
  - C. Tone Button
  - D. Vibration Button
  - E. Shock Button
  - F. Lock Switch (ON/OFF)
  - G. Charging Port
  - H. Shock Level Display
  - I. Channel Display (1: Control a dog, 2: Control another dog)
  - J. Knob for Shock Level +/-
Prepare the Receiver Collar:
- Turning ON the Receiver Collar: Press the On/Off Button. The Green LED will light up and flash every 4 seconds, indicating it's ready to receive a signal.
- Turning OFF the Receiver Collar: Press and hold the On/Off Button until the Red LED shuts off (approx. 3 seconds).
- Receiver Collar Components:
  - A. Contact Points
  - B. Charging Port (with cover)
  - C. On/Off Button
  - D. LED Indicator
  - E. Contact Spring Sheet
- Contact Points: Use the provided test tool to install contact points. Contact spring sheets can also be used for more effective and comfortable contact. Select contact points based on your dog's coat for best results.

Function Test

It is recommended to test the different levels on yourself, starting at the lowest level.

Place a finger over both Contact Points of the training collar.
Hold the remote approximately 2 feet from the training collar.
Press the Vibration Button continuously for 1-2 seconds; you should feel continuous vibration.
Rotate the knob to decrease levels. Starting at level 1, press the Shock Button. Increase the level until the sensation becomes uncomfortable.
Note: Continuous stimulation lasts for a maximum of 10 seconds. To reactivate, release and repress the button.

Button Functions:

Tone: Sends a non-adjustable tone to the Receiver Collar.
Vibration: Sends a non-adjustable vibration to the Receiver Collar.
Shock: Sends 1-16 adjustable levels of static stimulation to the Receiver Collar.

Caution: It is not recommended to press and hold the Vibration/Shock Button for too long to avoid physical or psychological harm to the dog.

How to Use the Test Lamp

Shock Function Test:

Turn on the Receiver Collar.
Hold the Test Lamp contacts against the Contact Points.
Press the Shock Button; the Test Lamp will light up. The brightness will increase with higher Shock Levels.

As a Screw Driver: Use the Test Lamp to tighten or loosen the Contact Points when preparing the Receiver Collar.

Pairing the Remote and Receiver Collar

Select Dog 1 on the Remote using the channel switch.
With the Remote ON and Receiver Collar OFF, press and hold the ON/OFF Button on the Receiver Collar for 4-5 seconds.
The Red & Green LEDs will blink for about 10 seconds, indicating it's ready for pairing.
Press and hold the Tone Button and Vibration Button simultaneously for 2-3 seconds. The Green LED on the Receiver Collar will blink 5 times, indicating successful pairing.
Pairing a Second Collar: Use the channel switch on the Remote to select Dog 2. Follow pairing steps 2-4.

Collar Fitting

For best results, fit the collar properly so the Contact Points press firmly against the dog's skin. You should be able to fit one finger between the Receiver Collar and the dog's neck.

Too tight: May cause the dog to breathe heavily.
Too loose: The Receiver Collar may move around, and the Contact Points could hurt the dog's skin.

Caution:

Do not shave the pet's neck, as this may increase the risk of skin irritation.
The collar should not be worn for more than 12 hours per day, as it may cause skin irritation.

Find the Best Shock Level for Your Pet

The unit has Up and Down buttons to control Shock Level (1 is lowest, 16 is highest). The appropriate level depends on your dog's temperament and sensitivity. Always start at the lowest level and gradually increase. The correct level is when the dog shows a mild reaction, such as an ear flick, lip lick, or neck muscle tension. The required Shock Level may vary depending on the training situation and distractions.

Device Information

Product Specifications

Battery Type: Rechargeable, lithium polymer battery
Battery Life (typical use): Remote: 27 days; Receiver: 11 days
Remote Waterproof Rating: Non-Waterproof (Keep away from water)
Receiver Waterproof Rating: IEC 60529 IPX7, Waterproof
Operating Temperature Range: 0-40°C (32-104°F)
Wireless Power: 20dBm (100mW)
Wireless Range: 300m (984 feet)

When the unit needs to be charged:

The indicator light on the Receiver Collar emits red every 4 seconds or flashes rapidly.
The 3-bar indicator on the Remote LCD shows only 1 bar.
The indicator light on the Remote or Receiver Collar does not come on.
The indicator light on the Remote or Receiver Collar comes on momentarily when a Mode Button is pressed.

Frequently Asked Questions (FAQ)

Is the Vibration/Shock safe for my pet? While unpleasant, it is harmless. Electronic training devices require owner interaction and training for desired results.
How old does my pet have to be? Pets should be at least 6 months old and able to recognize basic obedience commands.
Will my pet need to continue wearing the Receiver Collar after training? Possibly. Reinforcement with the Receiver Collar may be needed from time to time.
Is the Receiver Collar waterproof? Yes.
Will I get exactly 984 feet of range? Range varies by terrain, weather, vegetation, and other radio device transmissions. Refer to "To maximize the distance" for tips.
How long can I continuously deliver Vibration/Shock? A maximum of 10 continuous seconds. After this, there is a 5-second timeout before it can be delivered again.

Troubleshooting Guide

My pet does not respond when I press a button:

Ensure the Receiver Collar is turned on.
If range is reduced, batteries may be low in either the Remote or Receiver Collar.
Terrain, weather, vegetation, and other radio transmissions can impact range.
Test the Receiver Collar using the Test Lamp.
Increase the Shock Level.
Ensure the Receiver Collar's Contact Points are snugly against the pet's skin.

The Receiver Collar will not turn on:

Ensure the Receiver Collar has been charged (4 hours for initial charge, 2-3 hours for subsequent charges).
If the indicator light does not come on when a button is pressed, ensure batteries are charged properly.

The Receiver Collar is not responding to the Remote:

Ensure the Receiver Collar is on.
If the first two solutions do not resolve the issue, refer to "Pair the Remote and the Receiver Collar".

Warranty and Repair Information

1-Year Limited Lifetime Warranty

The original purchaser receives a 1-YEAR WARRANTY starting from the date of purchase. The first year covers Parts and Labor. Accessories like straps and batteries are covered for the first year only. After the first year, the Limited Lifetime Warranty covers Parts only, excluding Labor Fees and Accessories. Customers are responsible for shipping fees, out-of-warranty labor fees, and accessory costs after the first year. The warranty expires 5 years after a model is discontinued.

To Qualify for the Warranty:

Proof of purchase (original receipt) is required for warranty repairs. If proof of purchase is unavailable, the unit's age will be estimated by its serial number.

Not Covered Under Warranty:

Products bought secondhand or resold.
Defective units or refunds for purchases made more than 30 days prior (address issues with dealers for purchases within 30 days).
Repairs and replacements due to misuse, improper maintenance, or lost units.
Water damage on water-resistant components.
Units altered or damaged during unauthorized repair attempts.

Procedure for Repair Work:

Before sending the unit for service, consult the "Troubleshooting Guide". Customers are responsible for shipping costs for warranty repairs. The company is not liable for units damaged or lost in transit, loss of training time, or inconvenience during repair. Loaner units or compensation are not provided. A copy of the sales receipt may be required. Include a brief problem description, your name, address, phone numbers, and email address.

Compliance

FCC - USA

This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Modifications or changes to this equipment not expressly approved by the manufacturer may void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment causes harmful interference to radio or television reception, try to correct it by reorienting or relocating the receiving antenna, increasing the separation between the equipment and receiver, connecting the equipment to a different outlet, or consulting a dealer or technician.

FC CE RoHS MADE IN CHINA

	Shenzhen Patpet Technology Co., Ltd. - No-bark Collar FCC Attestation Attestation letter from Shenzhen Patpet Technology Co., Ltd. regarding FCC compliance for their No-bark Collar, model series P-collar 68x, FCC ID 2AHHYP-COLLAR682.
	Patpet No-Bark Collar Model Differences and Specifications This document outlines the model differences for the Patpet No-Bark Collar series, including FCC ID, model numbers, and confirmation that all models share the same internal circuitry and RF module.
	Patpet Remote Training Collar p-collar 630 & 630B Operating and Training Guide Comprehensive guide for the Patpet Remote Training Collar, including setup, operation, safety information, and troubleshooting for models p-collar 630 and p-collar 630B.
	Patpet P-collar 630 Remote Training Collar: Operating and Training Guide Comprehensive guide to the Patpet P-collar 630 remote dog training collar, covering features, operation, safety, troubleshooting, and warranty. Learn how to use tone, vibration, and light commands effectively.
	PATPET Remote Training Collar: Operating and Training Guide Comprehensive guide for the PATPET Remote Training Collar (p-collar 310/310B), covering safety, features, operation, training tips, troubleshooting, and warranty information.
	Patpet p-collar 511 No Bark Collar Quick Start Guide A quick start guide for the Patpet p-collar 511 No Bark Collar, covering setup, charging, operation, fitting, specifications, troubleshooting, and warranty information.
	PATPET p-collar 690 Quick Start Guide A quick start guide for the PATPET p-collar 690 dog training collar, covering setup, operation, troubleshooting, and warranty information.
	Patpet p-collar 350 Quick Start Guide This guide provides essential information for setting up and using the Patpet p-collar 350 dog training collar, including charging, pairing, and basic operation.