LEDone LOC-PT Series Installation Guide

Safety Instructions

Read instructions carefully before attempting to install fixture.

• All wiring should be performed by a qualified electrician.
• Disconnect power before installing or servicing. This fixture must be wired in accordance with the National Electrical Code and applicable local codes and ordinances.
• Proper grounding is required to ensure personal safety.
• This fixture is for outdoor use and should not be used in areas with limited ventilation or high ambient temperatures.

CAUTION: Risk of fire

WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.

Cleaning & Maintenance

CAUTION: Be sure the fixture temperature is cool enough to touch. Do NOT clean or maintain while the fixture is energized.

1. Clean glass lens with non-abrasive cleaning solution.
2. Do NOT open fixture to clean the LED. Do NOT touch the LED.

Note: These instructions do not cover all details or variation in equipment, nor do they provide for every possible situation during installation, operation or maintenance.

Troubleshooting

1. Check that the line voltage at fixture is correct. Refer to wiring directions.
2. Check that the fixture is grounded properly.

Pole Mounting

1. Make the wiring connections with UL approved connectors. Knot the wires for strain relief.
2. Tenon pole adaptor can fit tenon with 3" or 2 3/8" diameter. Slip tenon pole adaptor over tenon and secure the fixture to the tenon.
   • For 3" tenon, use the shorter (3/8") tenon set screw.
   • For the 2 3/8” tenon, use the longer (7/8”) tenon set screws.

Installation

Diagram Description: The fixture head attaches to a pole via a tenon adaptor. The head consists of a housing, three rods, housing wires, and a tenon pole adaptor. Housing wires are fed through rods, which screw into the housing. Fixture wires pass through the tenon pole adaptor, which slides onto the rods. A rubber mat is placed on the adaptor, and set screws secure the adaptor to the rods.

1. Feed the (3) housing wires through one of the three rods.
2. Screw the top of (3) rods into the housing. Be sure the housing clips are properly engaged onto the rods.
3. Feed fixture wires through the tenon pole adaptor.
4. Slide tenon pole adaptor on the 3 rods. Be sure the notches face the inside of the tenon pole adaptor.
5. Put the rubber mat onto the adaptor.
6. Tighten the (3) set screws at the tenon pole adaptor to secure rods.

Wiring

Universal voltage driver permits operation at 100V through 277V, 50/60Hz except for fixtures that factory ordered with a 120V photocell (/PC).

Standard Wiring

1. Connect the BLACK fixture lead to the (+) LIVE line supply wire.
2. Connect the WHITE fixture line to the NEUTRAL line supply wire.
3. Connect the GREEN fixture line to the supply ground.

0-10V Dimmable Wiring

Universal voltage driver permits operation at 120V through 277V, 50/60Hz. For 0-10V dimming, follow the wiring instructions below.

Diagram Description: The 0-10V dimming wiring diagram illustrates the connections between the power supply and the light fixture. It specifies how to connect the LINE, COMMON, DIM V+, DIM V-, and GROUND wires from the fixture to the corresponding supply leads. A YELLOW wire is indicated for Vaux 12V (auxiliary power).

Connection Mapping:

• (+) LINE supply lead connects to BLACK fixture lead.
• (-) COMMON supply lead connects to WHITE fixture lead.
• Supply ground connects to GROUND wire from fixture. DO NOT connect the GROUND of the dimming fixture to the output.
• (V+) DIM lead connects to PURPLE fixture lead.
• (V-) DIM lead connects to GRAY fixture lead.
• The driver comes with dimmable leads. If it is unused, make sure the leads are properly capped (if applicable).

Note: A YELLOW wire is present for Vaux 12V, which is an auxiliary voltage output from the driver.

Wattage and CCT Adjustable Table Switch Setting

Model: LOC-PT-MW(60/80/100/150)MCCT(30/40/50)DLV

Default Wattage: 150W

Default CCT: 5,000K

Diagram Description: The fixture features two switches, S1 and S2, for adjusting Wattage and Color Correlated Temperature (CCT). The table below shows the switch settings for different configurations.

Switch Settings:

• CCT Adjustment:
  • 3,000K: S1=1, S2=2
  • 4,000K: S1=2, S2=1
  • 5,000K: S1=1, S2=1
• Wattage Adjustment:
  • 150W: S1=1, S2=2
  • 100W: S1=2, S2=1
  • 80W: S1=1, S2=1
  • 60W: S1=2, S2=2

Note: The diagram shows a G 1/2" threaded connection for mounting.