Assembly Instructions
CAUTION: You must read these Assembly Instructions before you proceed.
Chair Assembly
Please look in the Seat Panel for hardware packs.
Part List
| Label | Picture | Description | QTY |
| A | [Seat Panel] | Seat Panel | 1 |
| B | [Right Leg Panel] | Right Leg Panel | 1 |
| C | [Left Leg Panel] | Left Leg Panel | 1 |
| D | [Backrest Panel] | Backrest Panel | 1 |
| E | [Seat Cushion] | Seat Cushion | 1 |
| F | [Back Cushion] | Back Cushion | 1 |
Hardware
| Label | Picture | Description | QTY |
| 1 | [Bolt] | Bolt (M6x40mm) | 11 |
| 2 | [Allen Wrench] | Allen Wrench | 1 |
Assembly Preparation
Before Beginning Assembly:
- Read instructions, cover to cover.
- Have 2 adults on hand for assembly.
- Do not assemble on flooring or carpet.
- Assemble on a clean non-marring surface (packing foam).
- Save all packaging until finished.
Assembly Steps
Overview
[Image of Chair with parts labeled: Seat Panel (A), Right Leg Panel (B), Left Leg Panel (C), Backrest Panel (D), Seat Cushion (E), Back Cushion (F)]
This Chair has multiple parts and may require up to 35 minutes to assemble. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1
[Image sequence: Unpacking parts]
Unpack and place all parts on a clean, non-marring surface.
Step 2
[Image sequence: Attaching leg panels to seat panel]
With assistance from your adult partner(s), place the Seat panel (A) upright onto a clean, soft surface to avoid any scratches or damage to the product. Attach the Right Leg Panel (B) to the Seat Panel (A) using Bolts (1) and the Allen Wrench (2). Repeat the same process with the Left Leg Panel (C). Do not fully tighten the Bolts at this time.
Step 3
[Image sequence: Attaching backrest panel]
With assistance from your adult partner(s), turn the assembled parts in step 2 upright. Attach the Backrest Panel (D) to the assembled parts in step 2 using Bolts (1) and the Allen Wrench (2). Do not fully tighten the Bolts at this time.
Step 4
[Image sequence: Adjusting levelers]
Inspect the Chair and make sure all parts are adequately connected. In a sequential manner, tighten all bolts at all joints. With assistance from your adult partner, adjust the Levelers to the desired height to avoid wobbles. CAUTION: When tightening these bolts, tighten sequentially. DO NOT tighten any bolt fully and then move towards the next one. This could cause the frame to warp. WARNING!! IF THE CHAIR IS NOT STABLE, IT COULD LEAD TO DAMAGING THE PRODUCT.
Step 5
[Image sequence: Placing cushions]
Place the Seat Cushion (E), then Back Cushion (F) onto the Chair, and affix the magic tape straps around the Chair as shown above. Your Chair is ready to be used. This Chair can only be used on a flat, level surface.
Care & Maintenance
- Do not put hot items directly on furniture surface.
- Do not clean furniture with harsh cleansers or polish.
- To obtain the longest lifespan of your outdoor products, minimizing exposure to direct sunlight is recommended.
- Children should not climb or jump on the furniture.
- Do not write on furniture without a padded barrier to protect the surface.
- To obtain the longest lifespan of your outdoor products, avoid extended and lengthy exposure to rain, snow, and direct sunshine. Whenever possible cover the product and/or place under patio or awnings.
- Not for commercial use. For residential use only.
- Stains may be removed with mild soap solution and damp cloth.
- Keep away from sources of ignition.
- Dust and pick-up spills using a clean, non-colored, lint-free cloth.
Loveseat Assembly
Please look in the Seat Panel for hardware packs.
Part List
| Label | Picture | Description | QTY |
| K | [Seat Panel] | Seat Panel | 1 |
| L | [Right Leg Panel] | Right Leg Panel | 1 |
| M | [Left Leg Panel] | Left Leg Panel | 1 |
| N | [Backrest Panel] | Backrest Panel | 1 |
| O | [Seat Cushion] | Seat Cushion | 1 |
| P | [Back Cushion] | Back Cushion | 2 |
Hardware
| Label | Picture | Description | QTY |
| 6 | [Bolt] | Bolt (M6x40mm) | 11 |
| 7 | [Allen Wrench] | Allen Wrench | 1 |
Assembly Preparation
Before Beginning Assembly:
- Read instructions, cover to cover.
- Have 2 adults on hand for assembly.
- Do not assemble on flooring or carpet.
- Assemble on a clean non-marring surface (packing foam).
- Save all packaging until finished.
Assembly Steps
Overview
[Image of Loveseat with parts labeled: Seat Panel (K), Right Leg Panel (L), Left Leg Panel (M), Backrest Panel (N), Seat Cushion (O), Back Cushion (P)]
This Loveseat has multiple parts and may require up to 45 minutes to assemble. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1
[Image sequence: Unpacking parts]
Unpack and place all parts on a clean, non-marring surface.
Step 2
[Image sequence: Attaching leg panels to seat panel]
With assistance from your adult partner(s), place the Seat Panel (K) upright onto a clean, soft surface to avoid any scratches or damage to the product. Attach the Right Leg Panel (L) to the Seat Panel (K) using Bolts (6) and the Allen Wrench (7). Repeat the same process with the Left Leg Panel (M). Do not fully tighten the Bolts at this time.
Step 3
[Image sequence: Attaching backrest panel]
With assistance from your adult partner(s), turn the assembled parts in step 2 upright. Attach the Backrest Panel (N) to the assembled parts in step 2 using Bolts (6) and the Allen Wrench (7). Do not fully tighten the Bolts at this time.
Step 4
[Image sequence: Adjusting levelers]
Inspect the Loveseat and make sure all parts are adequately connected. In a sequential manner, tighten all bolts at all joints. With assistance from your adult partner, adjust the Levelers to the desired height to avoid wobbles. CAUTION: When tightening these bolts, tighten sequentially. DO NOT tighten any bolt fully and then move towards the next one. This could cause the frame to warp. WARNING!! IF THE LOVESEAT IS NOT STABLE, IT COULD LEAD TO DAMAGING THE PRODUCT.
Step 5
[Image sequence: Placing cushions]
Place the Seat Cushion (O), then the Back Cushion (P) onto the Loveseat, and affix the magic tape straps around the Loveseat as shown above. Your Loveseat is ready to be used. This Loveseat can only be used on a flat, level surface.
Care & Maintenance
- Do not put hot items directly on furniture surface.
- Do not clean furniture with harsh cleansers or polish.
- To obtain the longest lifespan of your outdoor products, minimizing exposure to direct sunlight is recommended.
- Children should not climb or jump on the furniture.
- Do not write on furniture without a padded barrier to protect the surface.
- To obtain the longest lifespan of your outdoor products, avoid extended and lengthy exposure to rain, snow, and direct sunshine. Whenever possible cover the product and/or place under patio or awnings.
- Not for commercial use. For residential use only.
- Stains may be removed with mild soap solution and damp cloth.
- Keep away from sources of ignition.
- Dust and pick-up spills using a clean, non-colored, lint-free cloth.
Table Assembly
Please look in the Table Top for hardware packs.
Part List
| Label | Picture | Description | QTY |
| G | [Table Top] | Table Top | 1 |
| H | [Support Bar] | Support Bar | 2 |
| I | [Apron] | Apron | 2 |
| J | [Leg Frame] | Leg Frame | 2 |
Hardware
| Label | Picture | Description | QTY |
| 3 | [Screws] | Screws (M6x45mm) | 13 |
| 4 | [Screws] | Screws (M6x20mm) | 9 |
| 5 | [Allen Wrench] | Allen Wrench | 1 |
Assembly Preparation
Before Beginning Assembly:
- Read instructions, cover to cover.
- Have 2 adults on hand for assembly.
- Do not assemble on flooring or carpet.
- Assemble on a clean non-marring surface (packing foam).
- Save all packaging until finished.
Assembly Steps
Overview
[Image of Table with parts labeled: Table Top (G), Leg Frame, Apron (I)]
This Table has multiple parts and may require up to 35 minutes to assemble. Please read through the instructions herebelow to familiarise yourself with the parts and steps before assembly.
Step 1
[Image sequence: Unpacking parts]
Unpack and place all parts on a clean, non-marring surface.
Step 2
[Image sequence: Attaching support bars to table top]
With assistance from your adult partner(s), turn the Table Top (G) (bottom-side up) and place it on a clean, soft surface to avoid any scratches or damage to the product. Attach the Support Bar (H) to the Table top (G), then secure it using the Screws (3) and Allen Wrench (5). Repeat the same process with the remaining Support bar (H). Do not fully tighten the Screws at this time.
Step 3
[Image sequence: Attaching leg frames to table top]
With assistance from your adult partner(s), loosely affix one Leg Frame (I) onto the Table top (G), then screw it using the Screws (3) and Allen Wrench (5). Repeat the same process with the remaining Leg Frame (I). Do not fully tighten the Screws at this time.
Step 4
[Image sequence: Attaching aprons to leg frames]
With assistance from your adult partner(s), attach the Apron (J) to the Leg Frame (I), then secure it using the Screws (4) and Allen Wrench (5). Repeat the same process with the remaining Apron (J). Do not fully tighten the Screws at this time.
Step 5
[Image sequence: Turning table upright and checking for wobbles]
With assistance from your adult partner(s), turn the Table right side up. Exert pressure floorwards, onto the Table with both your hands. This pressure will help the Legs and Table Top reach full alignment status. Check for wobbles on a LEVEL surface. If no wobbles are found proceed to tighten the Screws in a sequential manner, until evenly secured. When tightening the Screws tighten sequentially. Caution: Do no tighten any Screws fully and then move on towards the next one. If there are still wobbles after tightening, loosen the Screws and execute the same above process. Your Table is ready to be used. This Table can only be used on a flat, level surface.
Care & Maintenance
- Do not put hot items directly on furniture surface.
- Do not clean furniture with harsh cleansers or polish.
- To obtain the longest lifespan of your outdoor products, minimizing exposure to direct sunlight is recommended.
- Children should not climb or jump on the furniture.
- Do not write on furniture without a padded barrier to protect the surface.
- To obtain the longest lifespan of your outdoor products, avoid extended and lengthy exposure to rain, snow, and direct sunshine. Whenever possible cover the product and/or place under patio or awnings.
- Not for commercial use. For residential use only.
- Stains may be removed with mild soap solution and damp cloth.
- Keep away from sources of ignition.
- Dust and pick-up spills using a clean, non-colored, lint-free cloth.
