Clover Flex 4 Pocket

Model Number: C407

Manufactured by: Clover Network, LLC

Address: 415 N Mathilda Ave Sunnyvale, CA 94085, USA

EU Importer: Marketplace Merchant Solutions Ltd, Unit 9, Richview Office Park Clonskeagh, Dublin 14, Ireland

Additional Manufacturer Info: Quanta Computer Inc (Model C407, HFS-C407, HFSC407)

Waste Electrical and Electronic Equipment (WEEE)

This product is covered electronic equipment under the European Union's Waste from Electrical and Electronic Equipment ("WEEE") Directive (2012/19/EU). The WEEE Directive requires that covered equipment be collected and managed separately from typical household waste in all EU member states. Please follow the guidance of your local environmental authority or ask the shop where you purchased the product for collection or recycling options.

RF Exposure and Regulatory Statements

Note: The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

Where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.

Radiation Exposure Statement

Canadian Compliance: To comply with Canadian RF exposure compliance requirements, this device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

Accessory Usage: This device has been tested and meets RF exposure guidelines when used with an accessory that does not contain any metal. Use of other accessories may not ensure compliance with RF exposure guidelines.

FCC Part 15 Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: [Condition 1] This device may not cause harmful interference, and [Condition 2] This device must accept any interference received, including interference that may cause undesired operation.

FCC Part 15 Class B Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC Radiation Exposure Statement: This device must not be co-located or operating in conjunction with any other antenna or transmitter. This device has been tested and meets FCC RF exposure guidelines. Use with an accessory that contains metal may not ensure compliance with FCC RF exposure guidelines.

Innovation, Science and Economic Development Canada (ISED) Statement

Statement: CAN ICES-3 (B)/NMB-3(B)

This device complies with ISED's licence-exempt RSSs. Operation is subject to the following two conditions: [Condition 1] This device may not cause harmful interference, and [Condition 2] This device must accept any interference received, including interference that may cause undesired operation.

Regulatory Information in the E-label

To find the regulatory information about your Flex, navigate to the Home screen and follow these steps:

Select "Settings"
Select "About device"
Select "Regulatory labels"

Quick Start Guide

For quick start guides and additional support, visit: clover.com/help/flex-4-pocket

Included in the Box:

[Package Contents: Clover Flex 4 Pocket device, power adapter, charging cable, documentation]

Regional Settings:

The device may require specific regional settings for optimal operation.

	Clover Flex 4 Quick Start Guide: Setup and Compliance Information Get started quickly with the Clover Flex 4 and its wireless cradle. This guide covers setup, included accessories, regional power adapters, and essential FCC/ISED compliance information.
	Clover Compact Quick Start Guide - Setup and Compliance A concise guide to setting up your Clover Compact POS device, including installation steps, power-on instructions, mounting options, and important FCC and WEEE compliance information.
	Clover Flex 4 Quick Start Guide - Setup, Specifications, and Compliance Get started with your Clover Flex 4 payment terminal. This guide covers setup, included items, safety precautions, and regulatory compliance information.
	Clover Mini 3 POS System Specifications and Features Detailed specifications and features of the Clover Mini 3, a compact countertop smart POS system. Includes comparison with Clover Mini 2, connectivity options, accessories, and payment flow.
	Clover Mobile Install Guide: Setup, Activation, and Transactions Comprehensive guide for setting up, activating, and using the Clover Mobile device for payment processing. Covers hardware setup, network connection, app installation, PIN management, printer pairing, and transaction handling.
	Clover Station Solo Quick Start Guide Official Quick Start Guide for the Clover Station Solo and Station Printer. Includes setup instructions, component identification, physical dimensions, FCC Part 15 compliance, radiation exposure statement, and WEEE recycling information.
	Clover Mini (2nd Generation) Quick Start Guide and Compliance Information Official quick start guide and regulatory compliance information for the Clover Mini (2nd generation) payment terminal, including setup instructions, FCC, ISED, and EU declarations.
	Clover Compact Quick Start Guide A quick start guide for the Clover Compact payment terminal, covering setup, installation of printer rolls, PIN shield, and power connection, along with FCC compliance information.