User Manual for Rayrun models including: N11 Single Color LED Dimmer, N11, Single Color LED Dimmer, Color LED Dimmer, LED Dimmer, Dimmer
N11 Nano RF Single Color LED Dimmer-Rayrun
Wireless Remote Control
Single Color LED Dimmer
Model: N11
Full Protection
High Power
Easy Operation
Compact Size
Wireless Remote Wide Voltage Range
2. LED output Connect LED fixtures to this terminal. Install positive
LED load cable into the terminal marked with `+' and negative cable into the terminal marked with `-'. Please make sure the LED rated voltage is same as the power supply and the maximum load current is lower than controller's rated current.
The controller will run into protection if the output is overloaded or short circuited. The indicator will flash red color and stop working in this case, Please check the wiring and load current to remove the fault.
3. Work status indicator This indicator displays all working status of the
controller. It shows different events as following: Steady green: Normal working. Single green blink: Command received. Long single green blink: Mode or color cycle edge. Long single yellow blink: Brightness or speed limit. Red flash: Overload protection. Yellow flash: Over heat protection. Green flash 3 times: New remote controller paired.
Functions
4. Turn ON / OFF Press `I' key to turn on unit or press `O' key to turn off.
Main unit will memorize the on/off status and will restore to the previous status on next power on.
Please use remote controller to turn on the unit if it
2 was switched to off status before previous power cut.
Introduction
N11 single color LED dimmer is designed to drive constant voltage LED products in voltage range of DC524V. The main unit works with a RF remote controller, user can adjust LED brightness on the remote controller. The main unit is powered by DC power supply and receives remote controller commands to drive LED fixtures.
Dimension
87mm 72mm
24mm
1
3
2
Wiring & Indicator
1. Power supply input
Install positive power cable into the terminal marked with `+' and negative power cable into the terminal marked with `-'. The controller can accept DC power from 5V to 24V, the output voltage is the same as the power supply, so please make sure the LED rated voltage is same as the power supply.
Do not power on the controller until all connection is firmly finished.
1
5. Brightness control
Press `+' key to increase brightness and press `-' key to decrease. The brightness will change smoothly when hold pressing these two keys.
The controller applies brightness gamma correction on dimming control, makes the brightness tuning more smooth to human sense.
4
7
5
100% 80% 60%
6
40% 20% 10%
6. Brightness shortcut keys These keys are shortcuts to fixed brightness. Press
each key to jump to the relevant brightness level. The controller applies brightness gamma correction on
dimming, the brightness level is valued to human sense, and not proportional to the LED output power.
3
7. Remote indicator This indicator blinks when remote controller is
working. If the indicator flash slowly when pressing keys, it means the remote battery is nearly empty and please change the battery in this case. The battery model is CR2032.
Operation
8. Using the remote Please pull out the battery insulate tape before using. The
RF wireless remote signal can pass through some nonmetal barrier. For proper receiving remote signal, please do not install the controller in closed metal parts.
9. Pair a new remote controller The remote controller and main unit is 1 to 1 paired for
factory default. It's possible to pair maximum 5 remote controllers to one main unit and each remote controller could be paired to any main unit.
You could pair a new remote controller to main unit by following steps:
1). Plug off the power of main unit and plug in again after more than 5 seconds.
2). Press `100%' and `60%' key simultaneously for about 3 seconds, within time of 10 seconds after the main unit powered on.
14
10. Recognize current remote only In some cases, one main unit might be paired with
several remote controllers but extra remote controllers are no longer needed. User could simply pair the current using remote to main unit again, then the main unit will dis-pair all other remote controllers and recognize current one only. 11. Protection
The main unit has full protection function for wrong wiring, output short circuit, overload and overheat. The controller will protect itself from damage at these extreme conditions and could automatically recover when working condition is good.
To avoid the protection, please ensure the LED fixtures are capable for constant voltage driving and in rated range, the cables are well connected and insulated. Also please install the controller with good ventilation and heat dissipation condition.
515
Specification
Model Brightness grade Brightness shortcut
PWM grade Overload protection Overheat protection
Working voltage Remote frequency Remote control distance Rated output current Controller dimension
N11 100 levels 6 levels 4000 steps
Yes Yes DC 5-24V 433.92MHz >15m at open area 1x10A 87x24x15mm
16
RF
LED
:N11
N11LED5V 24VLED L E D LED
87mm 72mm
24mm
1
3
2
1. 5V24V
"+" "-" LED
1
2.LED
L E D L E D "+" "-" LED
3.
3
4./
"I " "O "
2
5. "+" "-"
4
7
5
100% 80% 60%
6
40% 20% 10%
6.
3
7.
CR2032
8.
R F
9. 11 1
5
1 5 210 `1 0 0 % '`6 0 % ' 3 3
10.
11.
P W M
14
15
PWM
N11 100
6 4000
DC5-24V 433.92MHz >15 1x10A 87x24x15mm
16
Corel PDF Engine Version 18.1.0.661 CorelDRAW X8