Maximum Permissible Exposure Report

FCC ID: 2APPZ-H601W

Report prepared by: Shenzhen Tongzhou Testing Co.,Ltd

1 PRODUCT INFORMATION

EUT: IP Phone

Model Number: H601W, i501W

Model Declaration: All the same except for the model name, appearance color and appearance keys.

Test Model: H601W

Power Supply: DC 5V from adapter

Hardware version: V1.0

Software version: 2.12.20.4

2 EVALUATION METHOD

Systems operating under the provisions of FCC 47 CFR section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission's guidelines. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as mobile device whereby a distance of 0.2m normally can be maintained between the user and the device, and below RF Permissible Exposure limit shall comply with.

In accordance with KDB447498D01 for Simultaneous transmission MPE test exclusion applies when the sum of the MPE ratios for all simultaneous transmitting antennas incorporated in a host device, based on the calculated/estimated, numerically modelled or measured field strengths or power density, is ≤ 1.0. The MPE ratio of each antenna is determined at the minimum test separation distance required by the operating configurations and exposure conditions of the host device, according to the ratio of field strengths or power density to MPE limit, at the test frequency. Either the maximum peak or spatially averaged results from measurements or numerical simulations may be used to determine the MPE ratios. Spatial averaging does not apply when MPE is estimated using simple calculations based on far-field plane-wave equivalent conditions. The antenna installation and operating requirements for the host device must meet the minimum test separation distances required by all antennas, in both standalone and simultaneous transmission operations, to satisfy compliance.

3 LIMIT

3.1 Refer evaluation method

3.2 Limit

Limits for Maximum Permissible Exposure (MPE)/Controlled Exposure

Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute)
0.3 – 3.0 614 1.63 (100) * 6
3.0 – 30 1842/f 4.89/f (900/f²)* 6
30 – 300 61.4 0.163 1.0 6
300 – 1500 / / f/300 6
1500 – 100,000 / / 5 6

Limits for Maximum Permissible Exposure (MPE)/Uncontrolled Exposure

Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute)
0.3 – 3.0 614 1.63 (100) * 30
3.0 – 30 824/f 2.19/f (180/f²)* 30
30 – 300 27.5 0.073 0.2 30
300 – 1500 / / f/1500 30
1500 – 100,000 / / 1.0 30

F=frequency in MHz

*=Plane-wave equivalent power density

4 MPE CALCULATION METHOD

Predication of MPE limit at a given distance

Equation from page 18 of OET Bulletin 65, Edition 97-01

S=PG/4πR²

Where: S=power density

P=power input to antenna

G=power gain of the antenna in the direction of interest relative to an isotropic radiator

R=distance to the center of radiation of the antenna

5 ANTENNA INFORMATION

Antenna Gain and type refer to Antenna specification.

6 CONDUCTED POWER

WiFi 2.4GHz Band

TestMode Antenna Channel Result[dBm]
802.11bAnt1241213.22
802.11bAnt1243712.88
802.11bAnt1246212.92
802.11gAnt1241212.97
802.11gAnt1243712.84
802.11gAnt1246212.79
802.11n20Ant1241213.00
802.11n20Ant1243713.20
802.11n20Ant1246212.70
802.11n40Ant1242211.78
802.11n40Ant1243711.73
802.11n40Ant1245211.57
802.11ax20Ant1241211.88
802.11ax20Ant1243711.62
802.11ax20Ant1246211.61
802.11ax40Ant1242211.77
802.11ax40Ant1243711.64
802.11ax40Ant1245211.59

5G Band - UNII-1 Band

Test Mode Antenna Channel Result[dBm]
802.11aAnt1518012.89
802.11aAnt1520013.59
802.11aAnt1524013.75
802.11n20Ant1518012.26
802.11n20Ant1520012.43
802.11n20Ant1524013.17
802.11n40Ant1519012.41
802.11n40Ant1523012.68
802.11ac20Ant1518012.17
802.11ac20Ant1520012.87
802.11ac20Ant1524013.02
802.11ac40Ant1519012.35
802.11ac40Ant1523013.08
802.11ac80Ant1521012.49
802.11ax20Ant1518012.69
802.11ax20Ant1520012.73
802.11ax20Ant1524013.15
802.11ax40Ant1519012.93
802.11ax40Ant1523013.03
802.11ax80Ant1521013.14

5G Band - UNII-2A Band

Test Mode Antenna Channel Result[dBm]
802.11aAnt1526013.85
802.11aAnt1530013.73
802.11aAnt1532013.36
802.11n20Ant1526013.05
802.11n20Ant1530012.83
802.11n20Ant1532012.84
802.11n40Ant1527012.82
802.11n40Ant1531012.43
802.11ac20Ant1526012.93
802.11ac20Ant1530012.36
802.11ac20Ant1532012.76
802.11ac40Ant1527012.50
802.11ac40Ant1531012.98
802.11ac80Ant1529012.74
802.11ax20Ant1526012.47
802.11ax20Ant1530012.73
802.11ax20Ant1532012.77
802.11ax40Ant1527012.55
802.11ax40Ant1531012.48
802.11ax80Ant1529013.01

5G Band - UNII-2C Band

Test Mode Antenna Channel Result[dBm]
802.11aAnt1550013.11
802.11aAnt1558012.29
802.11aAnt1570012.52
802.11n20Ant1550011.03
802.11n20Ant1558011.47
802.11n20Ant1570011.45
802.11n40Ant1551011.19
802.11n40Ant1559011.70
802.11n40Ant1567011.35
802.11ac20Ant1550012.00
802.11ac20Ant1558011.84
802.11ac20Ant1570011.48
802.11ac40Ant1551011.03
802.11ac40Ant1559011.82
802.11ac40Ant1567011.37
802.11ac80Ant1553011.87
802.11ac80Ant1561011.62
802.11ax20Ant1550011.11
802.11ax20Ant1558012.07
802.11ax20Ant1570011.51
802.11ax40Ant1551012.09
802.11ax40Ant1559011.89
802.11ax40Ant1567011.03
802.11ax80Ant1553011.04
802.11ax80Ant1561011.47

5G Band - UNII-3 Band

Test Mode Antenna Channel Result[dBm]
802.11aAnt1574513.71
802.11aAnt1578512.94
802.11aAnt1582511.57
802.11n20Ant1574512.49
802.11n20Ant1578512.05
802.11n20Ant1582510.96
802.11n40Ant1575512.80
802.11n40Ant1579512.13
802.11ac20Ant1574513.21
802.11ac20Ant1578511.91
802.11ac20Ant1582511.31
802.11ac40Ant1575512.72
802.11ac40Ant1579512.02
802.11ac80Ant1577512.83
802.11ax20Ant1574512.73
802.11ax20Ant1578512.28
802.11ax20Ant1582511.39
802.11ax40Ant1575513.04
802.11ax40Ant1579512.19
802.11ax80Ant1577512.50

7 MANUFACTURING TOLERANCE

WiFi 2.4GHz Band

Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB)
IEEE 802.11b(Average)
Channel 112.51.0Channel 612.01.0Channel 1112.01.0
IEEE 802.11g(Average)
Channel 112.01.0Channel 612.01.0Channel 1112.01.0
IEEE 802.11n HT20(Average)
Channel 112.01.0Channel 612.51.0Channel 1112.01.0
IEEE 802.11n HT40(Average)
Channel 311.01.0Channel 611.01.0Channel 911.01.0
IEEE 802.11ax HE20(Average)
Channel 111.01.0Channel 611.01.0Channel 1111.01.0
IEEE 802.11ax HE40(Average)
Channel 311.01.0Channel 611.01.0Channel 911.01.0

UNII-1 Band

Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB)
IEEE 802.11a (Average)
Channel 3612.01.0Channel 4013.01.0Channel 4813.01.0
IEEE 802.11n HT20 (Average)
Channel 3612.01.0Channel 4012.01.0Channel 4813.51.0
IEEE 802.11ac VHT20 (Average)
Channel 3612.01.0Channel 4012.01.0Channel 4812.51.0
IEEE 802.11axVHT20 (Average)
Channel 3612.01.0Channel 4012.01.0Channel 4812.51.0
IEEE 802.11n HT40 (Average)
Channel 3812.01.0Channel 4612.01.0
IEEE 802.11ac VHT40 (Average)
Channel 3811.51.0Channel 4612.51.0
IEEE 802.11ax VHT40 (Average)
Channel 3812.01.0Channel 4612.51.0
IEEE 802.11ac VHT80 (Average)
Channel 4211.51.0
IEEE 802.11ax VHT80 (Average)
Channel 4212.51.0

UNII-2A Band

Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB)
IEEE 802.11a (Average)
Channel 5213.01.0Channel 6013.01.0Channel 6413.01.0
IEEE 802.11n HT20 (Average)
Channel 5212.51.0Channel 6012.01.0Channel 6412.01.0
IEEE 802.11ac VHT20 (Average)
Channel 5212.01.0Channel 6012.01.0Channel 6412.01.0
IEEE 802.11ax HE20 (Average)
Channel 5212.01.0Channel 6012.01.0Channel 6412.01.0
IEEE 802.11n HT40 (Average)
Channel 5412.01.0Channel 6212.01.0
IEEE 802.11ac VHT40 (Average)
Channel 5412.01.0Channel 6212.01.0
IEEE 802.11ax HE40 (Average)
Channel 5412.01.0Channel 6212.01.0
IEEE 802.11ac VHT80 (Average)
Channel 5812.01.0
IEEE 802.11ax HE80 (Average)
Channel 5812.51.0

UNII-2C Band

Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB)
IEEE 802.11a (Average)
Channel 10012.51.0Channel 11612.01.0Channel 14012.01.0
IEEE 802.11n HT20 (Average)
Channel 10010.51.0Channel 11610.51.0Channel 14010.51.0
IEEE 802.11ac VHT20 (Average)
Channel 10011.01.0Channel 11611.01.0Channel 14011.01.0
IEEE 802.11axVHT20 (Average)
Channel 10010.51.0Channel 11611.51.0Channel 14011.01.0
IEEE 802.11n HT40 (Average)
Channel 10611.01.0Channel 11011.01.0Channel 13411.01.0
IEEE 802.11ac VHT40 (Average)
Channel 10611.01.0Channel 11011.01.0Channel 13411.0--
IEEE 802.11ax VHT40 (Average)
Channel 10611.51.0Channel 11011.01.0Channel 13411.01.0
IEEE 802.11ac VHT80 (Average)
Channel 10611.01.0Channel 12211.01.0--
IEEE 802.11ax VHT80 (Average)
Channel 10610.51.0Channel 12210.51.0--

UNII-3 Band

Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB)
IEEE 802.11a (Average)
Channel 14913.01.0Channel 15712.01.0Channel 16511.01.0
IEEE 802.11n HT20 (Average)
Channel 14911.51.0Channel 15711.51.0Channel 16510.01.0
IEEE 802.11ac VHT20 (Average)
Channel 14912.51.0Channel 15711.01.0Channel 16511.01.0
IEEE 802.11axVHT20 (Average)
Channel 14912.01.0Channel 15711.51.0Channel 16510.51.0
IEEE 802.11n HT40 (Average)
Channel 15112.01.0Channel 15911.51.0
IEEE 802.11ac VHT40 (Average)
Channel 15112.01.0Channel 15911.51.0
IEEE 802.11ax VHT40 (Average)
Channel 15112.51.0Channel 15911.51.0
IEEE 802.11ac VHT80 (Average)
Channel 15512.01.0--
IEEE 802.11ax VHT80 (Average)
Channel 15512.01.0--

8 MEASUREMENT RESULTS

8.1 Standalone MPE

As declared by the Applicant, the EUT is a wireless device used in a fix application, at least 20 cm from any body part of the user or nearby persons; from the maximum EUT RF output power, the minimum separation distance, r =20cm, as well as the gain of the used antenna refer to antenna information, the RF power density can be obtained.

WiFi 2.4GHz Band

Modulation Type Output power (dBm) Output power (mW) Antenna Gain (dBi) Antenna Gain (linear) MPE (mW/cm²) MPE Limits (mW/cm²)
IEEE 802.11b13.522.3873.72.340.01041.0000
IEEE 802.11g13.019.9533.72.340.00931.0000
IEEE 802.11n HT2013.522.3873.72.340.01041.0000
IEEE 802.11n HT4012.015.8493.72.340.00741.0000
IEEE 802.11ax HE2012.015.8493.72.340.00741.0000
IEEE 802.11ax HE4012.015.8493.72.340.00741.0000

UNII-1 Band

Modulation Type Output power (dBm) Output power (mW) Antenna Gain (dBi) Antenna Gain (linear) MPE (mW/cm²) MPE Limits (mW/cm²)
IEEE 802.11a13.019.9535.13.240.01281.0000
IEEE 802.11n HT2013.522.3875.13.240.01441.0000
IEEE 802.11ac VHT2012.517.7835.13.240.01151.0000
IEEE 802.11ax VHT2012.517.7835.13.240.01151.0000
IEEE 802.11n HT4012.015.8495.13.240.01021.0000
IEEE 802.11ac VHT4012.517.7835.13.240.01151.0000
IEEE 802.11ax VHT4012.517.7835.13.240.01151.0000
IEEE 802.11ac VHT8011.514.1255.13.240.00911.0000
IEEE 802.11ax VHT8012.517.7835.13.240.01151.0000

UNII-2A Band

Modulation Type Output power (dBm) Output power (mW) Antenna Gain (dBi) Antenna Gain (linear) MPE (mW/cm²) MPE Limits (mW/cm²)
IEEE 802.11a13.019.9534.83.020.01201.0000
IEEE 802.11n HT2012.517.7834.83.020.01071.0000
IEEE 802.11ac VHT2012.015.8494.83.020.00951.0000
IEEE 802.11ax VHT2012.015.8494.83.020.00951.0000
IEEE 802.11n HT4012.015.8494.83.020.00951.0000
IEEE 802.11ac VHT4012.015.8494.83.020.00951.0000
IEEE 802.11ax VHT4012.015.8494.83.020.00951.0000
IEEE 802.11ac VHT8012.015.8494.83.020.00951.0000
IEEE 802.11ax VHT8012.517.7834.83.020.01071.0000

UNII-2C Band

Modulation Type Output power (dBm) Output power (mW) Antenna Gain (dBi) Antenna Gain (linear) MPE (mW/cm²) MPE Limits (mW/cm²)
IEEE 802.11a12.517.7835.43.470.01231.0000
IEEE 802.11n HT2010.511.2205.43.470.00771.0000
IEEE 802.11ac VHT2011.012.5895.43.470.00871.0000
IEEE 802.11ax VHT2011.514.1255.43.470.00971.0000
IEEE 802.11n HT4011.012.5895.43.470.00871.0000
IEEE 802.11ac VHT4011.012.5895.43.470.00871.0000
IEEE 802.11ax VHT4011.514.1255.43.470.00971.0000
IEEE 802.11ac VHT8011.012.5895.43.470.00871.0000
IEEE 802.11ax VHT8010.511.2205.43.470.00921.0000

UNII-3 Band

Modulation Type Output power (dBm) Output power (mW) Antenna Gain (dBi) Antenna Gain (linear) MPE (mW/cm²) MPE Limits (mW/cm²)
IEEE 802.11a13.019.9534.32.690.01071.0000
IEEE 802.11n HT2011.514.1254.32.690.00761.0000
IEEE 802.11ac VHT2012.517.7834.32.690.00951.0000
IEEE 802.11ax VHT2012.015.8494.32.690.00851.0000
IEEE 802.11n HT4012.015.8494.32.690.00851.0000
IEEE 802.11ac VHT4012.015.8494.32.690.00851.0000
IEEE 802.11ax VHT4012.517.7834.32.690.00951.0000
IEEE 802.11ac VHT8012.015.8494.32.690.00851.0000
IEEE 802.11ax VHT8012.015.8494.32.690.00851.0000

Remark:

9 CONCLUSION

The measurement results comply with the FCC Limit per 47 CFR 2.1091 for the uncontrolled RF Exposure of mobile device.

--------THE END OF REPORT----------

PDF preview unavailable. Download the PDF instead.

GetApplicationAttachment.html?id=8325768 Microsoft Word 2021

Related Documents

Preview Fanvil H601W IP Phone DFS Test Report
Official test report detailing the Dynamic Frequency Selection (DFS) tests conducted on the Fanvil H601W IP Phone, model numbers H601W and i501W, FCC ID 2APPZ-H601W, by Shenzhen Tongzhou Testing Co., Ltd.
Preview Fanvil H601W IP Phone RF Test Data and Technical Specifications
This document provides detailed RF test data for the Fanvil H601W IP Phone (FCC ID: 2APPZ-H601W), covering bandwidth, conducted output power, and power spectral density measurements conducted by Shenzhen Tongzhou Testing Co., Ltd.
Preview Fanvil H601W IP Phone: 2.4GHz WLAN Conducted Measurement Test Report
This document presents the conducted measurement test data for the Fanvil H601W IP Phone, covering 2.4GHz WLAN performance including bandwidth, output power, power spectral density, and spurious emissions.
Preview Fanvil H601W/i501W IP Phone FCC Test Report
This document is a test report for the Fanvil H601W and i501W IP Phone, detailing compliance with FCC regulations for wireless devices. It includes results for conducted power, power spectral density, bandwidth, radiated emissions, and power line conducted emissions.
Preview Fanvil Technology Co., Ltd FCC Authorization for Change in Identification
Letter from Fanvil Technology Co., Ltd to the FCC requesting authorization for a change in identification for their IP Phone, referencing FCC ID 2APPZ-H601W and 2BCUQ-H601W.
Preview Fanvil H601W/i501W IP Phone FCC Test Report
This FCC test report details the compliance testing for the Fanvil H601W and i501W IP Phone, covering wireless emissions and performance according to relevant standards.
Preview FCC Test Report: 2APPZ-H601W Spectrum Analysis and RF Performance
Detailed spectrum analysis and RF performance test results for the Fanvil H601W IP Phone (FCC ID: 2APPZ-H601W), including frequency band graphs and duty cycle measurements conducted by Shenzhen Tongzhou Testing Co., Ltd.
Preview U.S. Agent Letter of Attestation - Fanvil Technology Co., Ltd
Official U.S. Agent Letter of Attestation for Fanvil Technology Co., Ltd, designating Oasis Compliance, Inc. as the agent for FCC ID 2APPZ-H601W.