dormakaba USA | For every place that matters
Owner's Manual for dormakaba models including: ED50, ED100, ED250, ED100 Swing Door Operators, ED100, Swing Door Operators, Door Operators, Operators
This Owner's manual applies to dormakaba. ED50/ED100/ED250 swing door operators packaged in an overhead concealed header (OHC). Fig. 1.2 ED50 low energy OHC ...
prieš 2 dienas — This Owner's manual applies to dormakaba. ED50/ED100/ED250 swing door operators packaged in an overhead concealed header (OHC). Fig. 1.2 ED50 low energy OHC ...
This Owner's manual applies to dormakaba. ED50/ED100/ED250 swing door operators packaged in an overhead concealed header (OHC). Fig. 1.2 ED50 low energy OHC ...
File Info : application/pdf, 20 Pages, 2.23MB
DocumentDocumentED50/ED100/ED250
Swing Door Operators Installation in Overhead Concealed Header
Owner's Manual
DL4616-011 09-2021
| EN |
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
Table of Contents
Table of contents
Table of contents
2
1 General information
3
2 To our customers
4
3 What you should know
5
3.1 Distributor information
5
3.2 ED50 low energy operator
5
3.3 ED100/ED250 operator power
configuration
5
3.4 Low energy power operated swinging doors
ANSI/BHMA A156.19
5
3.5 Power operated swinging doors
ANSI/BHMA A156.10
5
3.5 Mode switch panel
6
4 AAADM safety information labels
7
4.1 Safety information label, full energy swing
doors (ANSI/BHMA A156.10)
7
4.2 Safety information label, low energy swing
doors (ANSI/BHMA A156.19)
8
5 Daily safety check procedure
9
5.1 Full energy power operated swing door
(ANSI/BHMA 156.10)
9
5.2 Low energy power operated swing door
(ANSI/BHMA 156.19)
11
6 General safety related items
12
6.1 Full energy power operated swing door
(ANSI/BHMA 156.10)
12
6.2 Low energy power operated swing door
(ANSI/BHMA 156.19)
13
7 ED50/ED100/ED250 door signage
14
7.1 ED100/ED250 operator configured for full
energy
14
7.2 ED50 operator and ED100/ED250
operator configured for low energy
14
7.3 Door signage, full energy power operated
single swing doors (ANSI/BHMA 156.10)
15
7.4 Door signage, low energy power operated
single swing doors (ANSI /BHMA 156.19):
initiation of door operation
15
7.5 Door signage, full energy power operated
double swing doors (ANSI/BHMA 156.10) 16
7.6 Door signage, low energy power operated
double swing doors, initiation of door
operation (ANSI/BHMA 156.19)
17
7.7 Door signage, full energy power operated
double egress swing doors
(ANSI/BHMA 156.10)
18
8 ED50/100/ED250 header
maintenance
19
8.1 ED50/ED100/ED250 environment and
cleaning
19
8.2 Operator status LEDs
19
2
ED50/ED100/ED250
DL4616-011
09-2021
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
Chapter 1
1 General information
1.1 Owner's manual. This Owner's manual applies to dormakaba ED50/ED100/ED250 swing door operators packaged in an overhead concealed header (OHC).
Fig.1.1 Single door OHC header with overhead arm
1.2 ED50/ED100/ED250 OHC header Installation.
NOTICE
Exterior door use. To insure proper suitability for exterior door use, the following topics must be addressed in the context of the door application setting. · Site-specific use factors such as high wind
conditions and/or building pressure.
· Door width, height, weight, and usage patterns.
· Observable prevailing conditions at the opening under which the operator is expected to perform. In some instances, this may require increased force settings to counteract these conditions.
· Door mounted presence sensors. When attempting to overcome these forces, it is strongly suggested that door mounted presence sensors be employed to enhance pedestrian safety through the opening.
1.3 Manual storage. This document must be kept in a secure place, and accessible for reference as required. If the door system should be transferred to another facility, insure that this document is transferred as well. 1.4 dormakaba.us website. Manuals are available for review, download, and printing on dormakaba.us website. 1.5 Dimensions Unless otherwise specified, all dimensions are given in inches ("). 1.6 Symbols used in this manual.
WARNING This symbol warns of hazards which could result in personal injury or threat to health.
NOTICE Draws attention to important information presented in this document.
Fig. 1.2 ED50 low energy OHC operator
Fig.1.3 ED100/ED250 OHC operator
ED50/ED100/ED250
DL4616-011
09-2021
3
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
2 To our customers
We are pleased that a dormakaba ED50/ED100/ED250 overhead concealed header (OHC) assembly has been selected for this swing door installation. dormakaba USA Inc. designed, tested and built this assembly to provide many years of service.
The purpose of this manual is to familiarize you with your ED50/ED100/ED250 overhead concealed header installed on a swing door.
It is essential that you "know your system" and that you recognize the importance of maintaining your door system in compliance with industry standards for safety.
It is your responsibility as owner and caretaker of the equipment, to inspect the operation of your door system on a daily basis as outlined in Chapter 5, Daily Safety Check Procedure to insure that it is safe for use by your customers and employees.
WARNING
Should the door fail to operate as prescribed in the Safety Information Checklist or at any other time for any reason, do not attempt to repair or adjust the ED50/ED100/ED250 overhead concealed swing door system!
Call your local authorized dormakaba USA Inc. distributor for repair. The distributor's AAADM certified technicians are trained to install and service the ED50/ED100/ED250 overhead concealed swing door system using the dormakaba USA, Inc. Installation and Setup Manuals and in accordance with ANSI/BHMA safety standards.
2.1 Service availability. dormakaba USA Inc. has a nationwide network of authorized distributors for sales, installation and service of its products.
2.2 Compliance with industry standards for safety. Your ED50/ED100/ED250 overhead concealed swing door system was designed to the latest ANSI/BHMA operating and safety standards. In order to insure the continued safe operation of the door, it is important that: · Proper decals and labels be applied and maintained
on your doors (Chapter 7).
· If decals and labels have been removed, or cannot be read, contact your local authorized dormakaba USA Inc. distributor for replacement decals or labels.
4
ED50/ED100/ED250
DL4616-011
Chapter 2 09-2021
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
Chapter 3
3 What you should know
3.1 Distributor information
3.1.1 dormakaba USA Inc. distributor information. Be sure that the dormakaba USA Inc. distributor has provided the following information for each door installation: 1. dormakaba USA Inc. ED50/ED100/ED250 Overhead
Concealed Owner's Manual DL4616-011.
2. Review of: · Daily Safety Check Procedure (Chapter 5).
· General Safety Related Items (Chapter 6).
3. Instructions on how to conduct the daily safety check procedure by walk through example.
4. Annual compliance inspection label completion (Chapter 4).
5. Circuit breaker or disconnect location for 115 Vac power to the ED50/ED100/ED250 overhead concealed header.
6. ED50/ED100/ED250 Mode switch panel location and instructions in its use (Para. 3.6).
7. Discussion of problems that could result from ED operator being allowed to operate after a malfunction observed.
8. Number to call for service or questions about your system if you are uncertain of any condition or situation.
WARNING
If there are any problems, discontinue door operation immediately and secure the door in a safe manner. Call your local dormakaba USA Inc. distributor for repair.
3.2 ED50 low energy operator
ED50 operator is available only as a low energy operator (Para. 3.4).
3.3 ED100/ED250 operator power configuration
1. ED100/ED250 operators can be configured for: · Low energy (Para. 3.4).
· Power operated (full energy) (Para. 3.5).
3.4 Low energy power operated swinging doors ANSI/BHMA A156.19
3.4.1 Low energy power operator door definition (ANSI/BHMAA156.19).
A door with a power mechanism that opens the door upon receipt of a knowing act signal, does not generate more kinetic energy than specified in the ANSI/BHMA A156.19 standard, and is closed by a power mechanism or other means.
3.4.2 Knowing act definition (ANSI/BHMA A159.19). Any conscious action with the expected result of opening a door. This includes but is not limited to: · Wall or jamb mounted contact or non contact
switches such as pushplates. · The action of of manually opening (pushing or
pulling) a door. · Controlled access devices such as keypads, card
readers, wireless transmitters and key switches.
3.5 Power operated swinging doors ANSI/BHMA A156.10
3.5.1 Power operated door definition (ANSI/BHMA A156.10).
The combination of door, operator, controls and sensors constituting the system. (also called automatic door.).
ED50/ED100/ED250
DL4616-011
09-2021
5
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
3.6 Mode switch and Exit Only switch panel
Fig. 3.6.1 Mode switch and Exit Only switch panel
Fig. 3.6.7 Optional key switch panels
1 2
4
3
Chapter 3
1 Mode switch panel 2 Mode switch,
three position
3.6.1 Mode switch positions.
Fig. 3.6.2 Auto Auto
Fig. 3.6.3 Close
Close
Fig. 3.6.4 Open
Open
3 Exit only switch, two position
4 RJ45 Comm port for service
3.6.2 Exit Only switch positions.
Fig. 3.6.5 On On
Fig. 3.6.6 Off
Off
3.6.3 Mode switch position descriptions. Auto 1. Door opens automatically when one of the activators
is actuated or triggered. Door closes on expiration of adjustable hold open time with no activators or actuators triggered.
2. With knowing act device actuation (Para. 3.4.2). Door will remain at full open position for not less than 5 seconds.
3. With push/pull actuation of door (Para. 7.2). Door will remain at full open position for not less than 3 seconds.
Close 1. Door will remain closed, or if door is open door will
close.
Open 1. Door opens automatically and remains open.
3.6.4 Exit Only switch position descriptions. On 1. Exterior activation sensor or knowing act device
disabled when door fully closed. · Only interior activation sensor or knowing act device
will enable door opening. Off 1. Both interior and exterior activation sensors or
knowing act devices will enable door opening.
6
ED50/ED100/ED250
DL4616-011
09-2021
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
Chapter 4
4 AAADM safety information labels
4.1 Safety information label, full energy swing doors (ANSI/BHMA A156.10)
4.1.1 Full energy automatic swing door safety information label.
This AAADM label (Fig. 4.1.1) outlines safety checks that should be performed daily on a swing door controlled by an ED100/ED250 OHC operator configured for full energy operation (ANSI/BHMA 156.10).
4.1.2 Safety information label location. Place label in a protected, visible location on door frame, near program switch panel if possible.
4.1.3 Annual compliance section of label. This section of label is only completed on automatic swing doors that comply with ANSI/BHMA A156.10 standard and pass inspection by an AAADM certified dormakaba USA Inc. technician.
4.1.4 Additional annual compliance inspection labels. Place additional labels (Fig. 4.1.2) over annual compliance inspection section of safety information label.
Fig. 4.1.1 Full energy safety information label
SAFETY INFORMATION
Automatic Swinging Doors
These minimum safety checks, in addition to those in the Owner's Manual, should be made each day and after any loss of electrical power.
1. Walk toward the door at a normal pace. The door should open when you are about 4 feet from the door.
2. Stand motionless on threshold for at least 10 seconds. The door should not close.
3. Move clear of the area. The door should remain open for at least 1.5 seconds and should close slowly and smoothly.
4. Repeat steps 1 through 3 from other direction if door is used for two way traffic.
5. Inspect the floor area. It should be clean with no loose parts that might cause user to trip or fall. Keep traffic path clear.
6. Inspect door's overall condition. The appropriate signage should be present.
7. Have door inspected by an AAADM certified inspector at least annually.
DO NOT USE DOOR if it fails any of these safety checks of if it malfunctions in any way. Call a qualified automatic door service company to have door repaired or serviced.
Fig. 4.1.2
Annual compliance label, full energy
ANNUAL COMPLIANCE INSPECTION
INSPECT FOR AND COMPLIES WITH ANSI
A156.10 ON: DATE: _____________ by AAADM Certified
Inspector Number: ____________
See Owner's manual or instructions for details on each of these and other safety items. If you need a copy of the manual, contact the manufacturer.
AAADM-2496
AAADM
American Association of Automatic Door Manufacturers
ANNUAL COMPLIANCE INSPECTION
INSPECT FOR AND COMPLIES WITH ANSI
A156.10 ON: DATE:______________
by AAADM Certified Inspector
Number:___________
ED50/ED100/ED250
DL4616-011
09-2021
7
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
Chapter 4
4.2 Safety information label, low energy swing doors (ANSI/BHMA A156.19)
4.2.1 Low energy swing door safety information label. This AAADM label (Fig. 4.2.1) outlines safety checks that should be performed daily on a swing door controlled by an:
· ED50 OHC operator.
· ED100/ED250 OHC operator configured for low energy operation (ANSI/BHMA A156.19).
4.2.2 Safety information label location. Place label in a protected, visible location on door frame, near operator power switch if possible.
4.2.3 Annual compliance section of label. This section of label is only completed on low energy swing doors that comply with ANSI/BHMA A156.19 standard and pass inspection by a AAADM certified dormakaba USA Inc. technician.
4.2.4 Additional annual compliance inspection labels. Place additional labels (Fig. 4.2.2) over annual compliance inspection section of safety information label.
Fig. 4.2.1 Low energy safety information label
SAFETY INFORMATION
Low Energy Swinging Doors
These minimum safety checks, in addition to those in the Owner's Manual, should be made each day and after any loss of electrical power.
1. Activate the door. Door should open at a slow smooth pace (4 or more seconds), and stop without impact.
2. Door must remain fully open for a minimum of 5 seconds before beginning to close.
3. Door should close at a slow, smooth pace (4 or more seconds), and stop without impact.
4. Inspect the floor area. It should be clean with no loose parts that might cause user to trip or fall. Keep traffic path clear.
Fig. 4.2.2 Annual compliance inspection label
ANNUAL COMPLIANCE INSPECTION
INSPECT FOR AND COMPLIES WITH ANSI
A156.19 ON: DATE: ______________
by AAADM Certified Inspector
Number: ___________
5. Inspect door`s overall condition. The appropriate signage should be present and the hardware should be in good condition.
6. Have door inspected by an AAADM certified inspector at least annually.
DO NOT USE DOOR if it fails any of these safety checks of if it malfunctions in any way. Call a qualified automatic door service company to have door repaired or serviced.
See Owner's manual or instructions for details on each of these and other safety items. If you need a copy of the manual, contact the manufacturer.
AAADM-3044
AAADM
American Association of Automatic Door Manufacturers
ANNUAL COMPLIANCE INSPECTION
INSPECT FOR AND COMPLIES WITH ANSI
A156.19 ON: DATE:______________
by AAADM Certified Inspector
Number:___________
8
ED50/ED100/ED250
DL4616-011
09-2021
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
Chapter 5
5 Daily safety check procedure
5.1 Full energy power operated swing door (ANSI/BHMA 156.10)
NOTICE
All figures and diagrams are for purposes of illustration only and are from AAADM power operated pedestrian door manual, reprinted with permission.
Fig. 5.1.1 One way traffic, overhead mounted safety sensor
Clear door opening
5.1.1 Performing daily safety checks. Perform safety checks daily on your automatic swinging door to insure your customer and employee safety. The daily safety checks are listed in Chapter 4, AAADM safety information labels.
TIPS AND RECOMMENDATIONS
Perform these checks while traffic is restricted from all detection and sensing zones.
43" [1092 mm]
Minimum activating detection
zone
5.1.2 Sensor activation, safety sensor detection. 1. Check activation sensor by walking toward door
opening at moderate speed, door should: · Start opening when you are about four feet from
door. · Open smoothly. · Stop at fully open without impact.
2. Move slowly through door opening (approximately six inches/second) stop in door swing path, and pause for ten seconds.
· Door should remain open.
3. If two way traffic, repeat from other side of door.
4. Step out of sensor zone activating area. · After a brief delay (minimum 1.5 seconds) door
should close smoothly and without impact.
5. For one way traffic, approach safety side of door and have someone else approach activating side.
· Door equipped with overhead mounted safety sensor (Fig 5.1.1), as long as you are in safety area of door it should not open.
· Door equipped with door mounted safety sensors (Fig 5.1.2, Fig. 5.1.3), door may start to open but should reverse, stop or slow down.
6. Stand motionless in door for at least 4 seconds. · Door equipped with overhead mounted presence
sensor (Fig 5.1.1), door should not close. · Door equipped with door mounted safety sensors
(Fig 5.1.2, Fig. 5.1.3), door may start to close but should reverse, stop or slow down.
Guide rail Guide rail
Guide rail Guide rail
Safety zone Safety zone
Safety detection zone
Fig. 5.1.2 One way traffic, door mounted safety sensors
Minimum activating detection
zone
Safety beam
ED50/ED100/ED250
DL4616-011
09-2021
9
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
5.1.3 Swing door double egress; knowing act switch activation.
1. Double egress doors are commonly activated by knowing act switch(es).
2. Operate knowing act device, doors should: · Open smoothly and stop at fully open without
impact. · Remain open for a minimum of five seconds before
closing.
3. As door closes, approach door from approach side: · Door should reopen.
4. Continue across threshold and stand motionless for 10 seconds:
· Door should not contact you.
Fig. 5.1.3 Two way traffic, activating and safety detection zones with door mounted safety sensors
Chapter 5
5. Continue through door, the door should: · Start closing after a minimum of five seconds. · Close smoothly and without impact. 6. Approach safety zone side of door: · If door equipped with overhead safety sensor
(Fig. 5.1.4) door should not open as long as you are in safety zone when door closed. · If door equipped with door mounted safety sensor (Fig. 5.1.5) door may start to open but should reverse, stop or slow down.
Fig. 5.1.4 Overhead safety sensors
Push plate
43" [1092 mm]
Minimum activating detection
zone
Secondary activation
zone
Safety zone
Safety zone
Secondary activation
zone
Push plate
Fig. 5.1.5 Door mounted safety sensors
Push plate
Safety zone Safety zone Safety zone Safety zone
Safety zone Safety zone
Minimum activating detection
zone
Edge of open door plus 55" [1397 mm] minimum guide rail
and activation
Pivot
Pivot Push plate
10
ED50/ED100/ED250
DL4616-011
09-2021
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
5.2 Low energy power operated swing door (ANSI/BHMA 156.19)
5.2.1 Performing daily safety checks. Perform safety checks daily on your low energy swing door to insure your customer and employee safety. These daily safety checks are also listed in Chapter 4, Safety Information labels, low energy swinging doors.
1. Activate the door by a knowing act (Para.3.4). · Door should open at a slow smooth pace
(4 seconds or more) and stop without impact.
2. Door must remain fully open for a minimum of 5 seconds before beginning to close.
· Door should close at a slow smooth pace (4 seconds or more) and stop without impact.
3. Inspect the floor area, it should be kept clean with no loose parts that might cause user to trip or fall. Keep traffic path clear.
4. Inspect door's overall condition. The appropriate signage (Chapter 7) should be present and all hardware should be in good condition.
5. Have door inspected by a dormakaba USA Inc. AAADM certified technician at least annually.
WARNING
If there are any problems, discontinue door operation immediately and secure the door in a safe manner. Call your local dormakaba USA Inc. distributor for repair.
Chapter 5
ED50/ED100/ED250
DL4616-011
09-2021
11
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
Chapter 6
6 General safety related items
6.1 Full energy power operated swing door (ANSI/BHMA 156.10)
6.1.1 Review safety related items and perform checks periodically as noted.
TIPS AND RECOMMENDATIONS
Perform these checks while traffic is restricted from all detection and sensing zones.
6. Lock stile: · With door open, grasp lock stile of door and attempt
to move horizontally and vertically. · There should be no looseness in the door pivots or in
connections between door and operator.
1. Housekeeping: · Check door area for tripping or slipping hazards. · Check all doors for damage. · Make sure all hardware and overhead covers are
properly secured. · There should be no bulletin boards, literature racks,
merchandise displays, or other attractions in the door area that would interfere with the use of the door or encourage people to stop and stand in the door area.
2. Door closing force: · Force to prevent the door from closing should not
exceed 30 pounds measured with a force gauge.
3. Door safety signage: · Refer to Chapter 7 for door safety signage
requirements. · Refer to Chapter 4 for Safety Information labels.
4. Activating switch, knowing act (Para. 3.4): · Doors equipped with a manual activating switch
shall hold door fully open for a minimum of five seconds before closing.
7. Breakout stop: · Center pivoted in swinging doors may be supplied
with an emergency breakout stop or switch that will allow the door to open in the direction of emergency egress. · When the door is pushed into the breakout mode, check that the door will not activate.
8. Traffic patterns: · Observe traffic patterns. Plan routing so people
enter and exit in a straight approach, directly toward the door opening.
9. Finger guard: · If installed, inspect finger guard to see that it is
secure and in good repair.
10. AAADM safety information label (Chapter 4): · An AAADM safety information label should be
affixed on the door or door frame in a protected, visible location. · If you need additional decals or labels, contact your local authorized dormakaba USA Inc. distributor.
5. Guide rails (Fig. 6.1.1, Fig. 6.1.2), if used: · Check that guide rails or other barriers or separators
are present (two per swing door side) and firmly anchored. · Rail lengths should be the width of the open door or greater.
WARNING
If there are any problems, discontinue door operation immediately and secure the door in a safe manner. Call your local dormakaba USA Inc. distributor for repair.
Fig. 6.1.1 Guide rails, jamb and floor mounted
Width of door minimum
30" [762 mm] minimum
Panel
Fig. 6.1.2 Guide rails, free standing, floor mounted
Width of door minimum
"6" [152 mm] maximum
Divider
30" [762 mm] minimum
Door jamb Door jamb
12
ED50/ED100/ED250
DL4615-013
09-2021
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
6.2 Low energy power operated swing door (ANSI/BHMA 156.19)
6.2.1 Review safety related items and perform checks periodically as noted.
TIPS AND RECOMMENDATIONS
Perform these checks while traffic is restricted.
1. Housekeeping: · Check door area for tripping or slipping hazards. · Make sure all hardware and overhead covers are
properly secured. · There should be no bulletin boards, literature racks,
merchandise displays, or other attractions in the door area that would interfere with the use of the door or encourage people to stop and stand in the door area.
2. Check all doors for damage.
3. Door closing force: · Force to prevent the door from closing should not
exceed 15 pounds measured with a force gauge.
4. Door safety signage: · Refer to Chapter 7 for door safety signage
requirements. Chapter 4 documents safety information (daily safety check) and annual compliance inspection labels requirements.
5. Lock stile: · With door open, grasp lock stile of door and attempt
to move horizontally and vertically. · There should be no looseness in the door pivots or in
connections between door and operator.
6. Breakout stop: · Center pivoted in swinging doors may be supplied
with an emergency breakout stop or switch that will allow the door to open in the direction of emergency egress. · When the door is pushed into the breakout mode, check that the door will not activate.
WARNING
If there are any problems, discontinue door operation immediately and secure the door in a safe manner. Call your local dormakaba USA Inc. distributor for repair.
Chapter 6
ED50/ED100/ED250
DL4615-013
09-2021
13
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
Chapter 7
7 ED50/ED100/ED250 door signage
7.1 ED100/ED250 operator configured for full energy
7.1.1 Overview Signage and warnings are specified in ANSI /BHMA A156.10, American National Standard for Power Operated Pedestrian Doors, paragraph 11. 7.1.2 Door, one way traffic, Fig. 7.1.1. 1. Arrow and AUTOMATIC DOOR, one side of decal. · Shall be visible from approach side of a swinging door,
mounted on door at a height of 50" ± 12" from floor to centerline of sign. 2. DO NOT ENTER and AUTOMATIC DOOR, one side of decal (or separate decal for solid doors - DD0739-020). · Shall be visible from non-approach side of door that swings towards pedestrians attempting to travel in wrong direction. 7.1.3 Door, two way traffic, Fig. 7.1.2. 1. Arrow and AUTOMATIC DOOR, one side of decal. · Shall be visible from approach side of a swinging door, mounted on door at a height of 50" ± 12" from floor to centerline of sign. 2. CAUTION AUTOMATIC DOOR, one side of decal. · Swinging doors serving both egress and ingress shall have a "CAUTION AUTOMATIC DOOR" sign visible from swing side of door. · Sign shall be mounted on door at a height of 50 ± 12" from floor to centerline of sign.
Fig. 7.1.1 One decal, approach side, non-approach side
AUTOMATIC DOOR
DD0739-010
Fig. 7.1.2 One decal, two way traffic
DO NOT
ENTER
AUTOMATIC DOOR
DD0739-010
AUTOMATIC DOOR
DD0756-010
AUTOMATIC
CAUTION
DOOR
dormakaba
DD0756-010
Fig. 7.1.3 ACTIVATE SWITCH TO OPERATE decal
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
DD0758-010
7.1.4 Knowing act door. 1. ACTIVATE SWITCH TO OPERATE decal. · Knowing act doors shall have signage stating
"ACTIVATE SWITCH TO OPERATE" on side of door having knowing act switch or other knowing act device.
7.2 ED50 operator and ED100/ED250 operator configured for low energy
7.2.1 Overview Signage and warnings are specified in ANSI /BHMA A156.19, American National Standard for Power Assist and Low Energy Power Operated Doors. 7.2.2 All low energy doors. 1. AUTOMATIC CAUTION DOOR decal. · All low energy doors shall be marked with signage
visible from both side of door with the words "AUTOMATIC CAUTION DOOR". · Signs shall be mounted 50" ± 12" from floor to centerline of sign. 7.2.3 Knowing act switch used to initiate door operation. 1. ACTIVATE SWITCH TO OPERATE decal. · When a knowing act device is used to initiate operation of door operator, door shall be provided with sign on each side of door where switch is operated with message "ACTIVATE SWITCH TO OPERATE". 7.2.4 Push/Pull used to initiate door operation. 1. PUSH TO OPERATE, PULL TO OPERATE decals. · When push/pull is used to initiate operation of door operator, doors shall be provided with the message "PUSH TO OPERATE" on push side of door and "PULL TO OPERATE" on pull side of door.
Fig. 7.2.1 AUTOMATIC CAUTION DOOR decal
AUTOMATIC
CAUTION
DOOR
DD0586-010
DD0586-010
Fig. 7.2.2 ACTIVATE SWITCH TO OPERATE decal
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
DD0758-010 1
1 Activate Switch to Operate DD0758-010
Fig. 7.2.3 PUSH TO OPERATE, PULL TO OPERATE decals
PUSH TO OPERATE 2
DD0762-010
DD0762-010
2 Push to Operate DD0762-010
PULL TO OPERATE
3
DD0762-020
DD0762-020
3 Pull to Operate DD0762-020
14
ED50/ED100/ED250
DL4616-011
09-2021
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
Chapter 7
7.3 Door signage, full energy power operated single swing doors (ANSI/BHMA 156.10)
Fig. 7.3.1 One decal, one way traffic
Approach side
Swing side
Fig. 7.3.3 One decal, two way traffic
Approach side
Swing side
AUTOMATIC DOOR
50" ± 12"
DO NOT
ENTER
AUTOMATIC DOOR
DD0739-010
AUTOMATIC DOOR
50" ± 12"
AUTOMATIC CAUTION
DOOR
dormakaba DD0756-010
Fig. 7.3.2 One way traffic
Swing side
Fig. 7.3.4 Two way traffic
Swing side
Approach side
Approach side
7.4 Door signage, low energy power operated single swing doors (ANSI /BHMA 156.19): initiation of door operation
Fig. 7.4.1 Knowing act device
Fig. 7.4.2 Push/Pull Push To Operate
Pull To Operate
AUTOMATIC CAUTION
DOOR
DD0586-010
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
50" ± 12"
AUTOMATIC CAUTION
DOOR
DD0586-010
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
AUTOMATIC
CAUTION
DOOR
DD0586-010
PULL TO OPERATE
DD0762-020
50" ± 12"
PULL TO OPERATE
DD0762-020
AUTOMATIC CAUTION
DOOR
DD0586-010
PUSH TO OPERATE
DD0762-010
PUSH TO OPERATE
DD0762-010
ED50/ED100/ED250
DL4616-011
09-2021
15
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
7.5 Door signage, full energy power operated double swing doors (ANSI/BHMA 156.10)
Fig. 7.5.1 One way traffic, approach side
Fig. 7.5.4 One way traffic, swing side
Chapter 7
AUTOMATIC DOOR
50" ± 12"
AUTOMATIC DOOR
DO NOT ENTER AUTOMATIC
DOOR DD0739-010
50" ± 12"
DO NOT
ENTER
AUTOMATIC DOOR
DD0739-010
Fig. 7.5.2 Two way traffic, approach side
AUTOMATIC DOOR
50" ± 12"
AUTOMATIC DOOR
Fig. 9.5.5 Two way traffic, swing side
AUTOMATIC CAUTION
DOOR
dormakaba DD0756-010
50" ± 12"
AUTOMATIC CAUTION
DOOR
dormakaba DD0756-010
Fig. 7.5.3 Knowing act, approach side, one way
Fig. 7.5.6 Knowing act, swing side, one way
AUTOMATIC DOOR
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
50" ± 12"
AUTOMATIC DOOR
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
DO NOT ENTER AUTOMATIC
DOOR DD0739-010
50" ± 12"
DO NOT
ENTER
AUTOMATIC DOOR
DD0739-010
16
ED50/ED100/ED250
DL4616-011
09-2021
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
7.6 Door signage, low energy power operated double swing doors, initiation of door operation (ANSI/BHMA 156.19)
Fig. 7.6.1 Knowing act device, approach side
Fig. 7.6.3 Knowing act device, swing side
Chapter 7
AUTOMATIC CAUTION
DOOR
DD0586-010
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
50" ± 12"
AUTOMATIC CAUTION
DOOR
DD0586-010
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
AUTOMATIC CAUTION
DOOR
DD0586-010
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
50" ± 12"
AUTOMATIC CAUTION
DOOR
DD0586-010
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
ACTIVATE SWITCH TO OPERATE
DD0758-010 DD0758-010
Fig. 7.6.2 Push/Pull, Push
Fig. 7.6.4 Push/Pull, Pull
AUTOMATIC CAUTION
DOOR
DD0586-010
PUSH TO OPERATE
DD0762-010
50" ± 12"
PUSH TO OPERATE
DD0762-010
AUTOMATIC CAUTION
DOOR
DD0586-010
PUSH TO OPERATE
DD0762-010
PUSH TO OPERATE
DD0762-010
AUTOMATIC CAUTION
DOOR
DD0586-010
PULL TO OPERATE
DD0762-020
50" ± 12"
PULL TO OPERATE
DD0762-020
AUTOMATIC CAUTION
DOOR
DD0586-010
PULL TO OPERATE
DD0762-020
PULL TO OPERATE
DD0762-020
ED50/ED100/ED250
DL4616-011
09-2021
17
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
Chapter 7
7.7 Door signage, full energy power operated double egress swing doors (ANSI/BHMA 156.10)
Fig. 7.7.1 OHC RH double egress
Fig. 7.7.4 OHC LH double egress
Swing side Approach side
Fig. 7.7.2 RH double egress, interior side
Swing side
Approach side
Approach side Swing side
Fig. 7.7.5 LH double egress, interior side
Approach side
Swing side
DO NOT ENTER AUTOMATIC
DOOR DD0739-010
50" ± 12"
AUTOMATIC DOOR
AUTOMATIC DOOR
50" ± 12"
DO NOT
ENTER
AUTOMATIC DOOR
DD0739-010
Fig. 7.7.3 RH double egress, exterior side
Swing side
Approach side
Fig. 7.7.6 LH double egress, exterior side
Approach side
Swing side
DO NOT ENTER AUTOMATIC
DOOR DD0739-010
50" ± 12"
AUTOMATIC DOOR
AUTOMATIC DOOR
50" ± 12"
DO NOT
ENTER
AUTOMATIC DOOR
DD0739-010
18
ED50/ED100/ED250
DL4616-011
09-2021
dormakaba ED50/ED100/ED250 Owner's Manual Overhead concealed header
Chapter 8
8 ED50/100/ED250 header maintenance
8.1 ED50/ED100/ED250 environment and cleaning
Table 8.3.1 Operator environmental requirements Ambient temperature 5 to 122 °F
Fig. 8.3.1 ED50/ED100/ED250 overhead concealed header
8.1.1 ED50/ED100/ED250 environmental requirements.
ED50/ED100/ED250 overhead concealed header assembly is designed to operate under the environmental specifications shown in Table 8.3.1.
8.1.2 Areas around door(s) and door swing radius. Areas around doors and door swing radius must be kept clear of all obstacles.
8.1.3 Cleaning of header.
WARNING
Cleaning of all header surfaces must be done with Mode switch (Para. 3.5) in CLOSE position!
External surfaces of the header can be cleaned with a damp cloth and commercial cleaning agents.
TIPS AND RECOMMENDATIONS
Abrasive (scouring) agents should not be used as they may damage external surfaces.
8.2 Operator status LEDs
Fig. 8.2.1 Operator status LEDs, header cover removed
6 21
4
5
1 Red LED 2 Yellow LED 3 Green LED
3
4 Accessory terminal board
5 OHC header 6 Power Off/On switch
8.1.4 Water and other liquids.
CAUTION
No water or other liquids must be sprayed or spilled on ED50/ED100/ED250 overhead concealed header!
8.2.1 Operator status LEDs. 1. Red LED
Blinking codes are used to indicate "ln__" information (system status or operating conditions) or certain error codes "E__".
2. Yellow LED Maintenance interval indicator. When illuminated, an indication the operator system has to be serviced.
3. Green LED · On, internal 24 Vdc power is On. · Off, internal 24 Vdc power is Off.
TIPS AND RECOMMENDATIONS
Details on LED status codes and maintenance intervals can be found in Appendix B Troubleshooting.
ED50/ED100/ED250
DL4616-011
09-2021
19
www.dormakaba.us
dormakaba USA Inc. 1 Dorma Drive, Drawer AC Reamstown, PA 17567 USA T: 717-336-3881 F: 717-336-2106