Goldstrike Tail Light Flash Module with Lightstrike™

Important Information

WARNING: Ignoring the contents described herein can result in potential serious injury or death if not followed.

CAUTION: Ignoring the contents described herein can or will result in material damage and/or personal injury.

ATTENTION: Ignoring this detail will affect the performance or functionality of the product.

General Product Information & Warranty

All Ciro products are designed for "easy assembly" and/or "plug and play". Ciro recommends a competent mechanic install their products, using standard mechanical procedures to assure a safe and successful installation. Read completely and understand the instructions prior to starting installation.

Ciro products are designed and manufactured under very strict quality control. Ciro warrants that products sold to the original purchaser shall be free from any defects in materials and workmanship for a period of 3 (three) years from the date of purchase, and a limited lifetime warranty against LED failure. Ciro will have no obligation if the customer cannot show proof of purchase. Warranty will not be granted unless the part is properly installed, unmodified, and maintained. Ciro will not be liable for any consequential and incidental damages, including labor, or non-Ciro products. Please visit Ciro3d.com for their complete warranty policy.

Included Items

48019 Tail Light Flash Module

Installation Instructions

Open the saddlebags and remove the two side panels below the seat. Disconnect the heated seat harness. Using a 6mm allen wrench, remove the seat screws on each side. Pull straight up on the front of the seat, then slide the seat forward to release the rear of the seat.
Visual Aid Description: Figure 1 shows the heated seat harness connection. Figure 2 illustrates the use of a 6mm allen wrench to remove seat screws.
Locate the left and right rear lighting connectors. Unplug both connectors by pressing the release tab and pulling them apart.
Visual Aid Description: Figure 3 depicts the left and right rear lighting connectors, highlighting the release tab.
Route the left and right in-line connector cables under the frame crossbar towards the rear of the motorcycle. The flash module should be positioned next to the right side of the frame near the fuel tank.
Visual Aid Description: Figure 4 illustrates the routing of the feed wires under the crossbar and the placement of the flash module on the right side of the motorcycle frame. It labels the front and right/left sides.
Determine the left and right Goldstrike connector plugs by checking the labels. Plug them in-line with the factory wiring connectors that were disconnected in step 2. Ensure the large connectors are placed out of the way so the seat will not crush them.
Visual Aid Description: Figure 5 shows the process of plugging in the connectors, tucking them out of the way to avoid the frame, and positioning the flash module.
Download the Lightstrike app from your app provider. The default password is 000000 (six zeros). Test the lighting functions.
Plug in the heated seat harness and reinstall the seat, ensuring that wires and connectors are not being pinched.

Lightstrike App Control

The Lightstrike module uses your smartphone and Bluetooth to control the product. Follow these steps:

Download the Lightstrike app from your iOS or Android app store.
The default password is 000000 (six zeros).
For additional information and installation videos, scan the QR code provided with the product packaging.

Installation Recommendations

The 48019 tail light flash module provides limited Lightstrike customization for lights connected behind it. It is intended for use with OEM tail lights, but additional features may be available with other accessory lighting. If connecting to lights with built-in Lightstrike features, functions may conflict.

Ciro recommends installing the 48019 tail light flash module in one of three ways:

No Other Plug & Play Harnesses: Plug the suitable left/right connectors directly in-line with the OEM left/right connectors located near the rear of the under-seat area.
With Existing 48000 Plug & Play Harness (No Other Lightstrike Lighting): Plug the 48019 Tail Light Flash Module ahead of the 48000 plug and play harness. This allows the 48019 module to affect all downstream brake lighting, adding limited brake functions to each of those lights.
With Existing 48000 Plug & Play Harness (With Other Lightstrike Lighting): To ensure each lighting product works as originally intended, plug the 48019 Tail Light Flash Module in behind the 48000 plug and play harness. This allows original Lightstrike lights to be customized individually through the app, and the flash module will only affect lights connected behind it.

Note: It is also possible to add a second 48000 plug and play harness. This would allow the 48019 tail light flash module to control some, but not all, installed lights. The 48019 module should be installed between the two 48000 plug and play harnesses. Lights ahead of the module will not be affected by its customization settings, but lights after the 48019 would gain functions.

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Document Revision: G0048019, REV.- For the latest version of installation instructions, visit www.goldstrike3d.com.