Compliance proofs for products: LANCOM Systems GmbH
User Guide for LANCOM Systems models including: LX-6400, LX-6402, Highly Efficient Wi-Fi, Efficient Wi-Fi, LX-6400, Wi-Fi
LANCOM LX-6402: LANCOM Systems GmbH
File Info : application/pdf, 1 Pages, 616.50KB
DocumentDocument111856/0622 LED description & technical details owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their Hardware Quick Reference LANCOM LX-6400 LANCOM LX-6402 2.5G Config (Com) Reset DC 12 V ETH2 ETH1 (PoE) USB Wi-Fi antenna connectors (only LX-6402) Screw the supplied Wi-Fi antennas onto the dedicated connectors. Serial interface You can optionally configure the device by connecting it to a PC with a configuration cable (separately available). Reset button Pressed up to 5 seconds: device restart RESET Pressed longer than 5 seconds: configuration reset and device restart Power After connecting the cable to the device, turn the connector 90° clockwise to prevent it from accidental unplugging. Use only the supplied power adapter. Ethernet interfaces Use the cable with the Ethernet connectors to connect interface ETH1 (PoE) or ETH2 to your PC or a LAN switch. USB interface Connect compatible USB devices either directly to the USB interface, or use a suitable USB cable. Mounting & connecting Power Off Green, permanently* Blue / red, alternatingly blinking 1x green inverse blinking* 2x green inverse blinking* 3x green inverse blinking* Purple, blinking Purple, permanently Yellow / green, blinking alternating with WLAN Link LED Device switched off Device operational, resp. device paired / claimed and LANCOM Management Cloud (LMC) accessible. DHCP error or DHCP server not accessible (only when configured as DHCP client) Connection to the LMC active, pairing OK, claiming error. Pairing error, resp. LMC activation code / PSK not available. LMC not accessible, resp. communication error. Firmware update Device booting The access point searches for a WLAN controller WLAN Link Off Green, permanently Green, inverse flashing Green, blinking Red, blinking Yellow / green, blinking alternating with power LED No Wi-Fi network defined or Wi-Fi module deactivated. The Wi-Fi module is not transmitting beacons. At least one Wi-Fi network defined and Wi-Fi module activated. The Wi-Fi module is transmitting beacons. Number of flashes = number of connected Wi-Fi stations DFS scanning or other scan procedure Wi-Fi module hardware error The access point searches for a WLAN controller Hardware Power supply 12 V DC, external power adapter (110 V or 230 V) with bayonet connector to secure against disconnection, or PoE based on 802.3at via ETH1 Power consumption Max. 22 W via 12 V / 2.5 A power adapter (value refers to the total power consumption of access point and power adapter), Max. 24 W via PoE (value solely refers to the power consumption of the access point) Environment Temperature range 040 °C Access point overheating is avoided by automatic throttling of the Wi-Fi modules. Humidity 0-95 %; non-condensing Housing Robust synthetic housing, rear connectors, ready for wall and ceiling mounting; measures 205 x 42 x 205mm (W x H x D) Number of fans None; fanless design, no rotating parts, high MTBF Wi-Fi Frequency band Radio channels 2.4 GHz Radio channels 5 GHz 2400-2483.5 MHz (ISM) or 5180-5700 MHz (restrictions vary between countries) Up to 13 channels, max. 3 non-overlapping (2.4 GHz band) Up to 19 non-overlapping channels (automatic dynamic channel selection required) Interfaces ETH1 (PoE) ETH2 Serial interface 10 / 100 / 1000 / 2.5G Base-T; PoE adapter compliant to IEEE 802.3at required 10 / 100 / 1000 Base-T Serial configuration interface / COM-port (8-pin mini-DIN): 115,000 baud Package content Antennas (only LX-6402) Cable Power adapter Four dipole dual-band antennas, maximum gain: 2,3 dBi in the 2.4 GHz band, 5 dBi in the 5 GHz band. Ethernet cable, 3 m External power adapter, 12 V / 2.5 A DC/S, barrel connector 2.1 / 5.5 mm bayonet, LANCOM item no. 111760 (EU, 230 V) (not for WW devices) and/or omissions. Cloud-ready Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide! Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times. Please observe the following when setting up the device i The power plug of the device must be freely accessible. For devices to be operated on the desktop, please attach the adhesive rubber footpads. Do not rest any objects on top of the device. Keep all ventilation slots on the side of the device clear of obstruction. Lockable wall and ceiling mounting with the LANCOM Wall Mount (LN) (available as an accessory) Please note that support service for third-party accessories is excluded. *) The additional power LED statuses are displayed in 5-seconds rotation if the device is configured to be managed by the LANCOM Management Cloud. This product contains separate open-source software components which are subject to their own licenses, in particular the General Public License (GPL). The license information for the device firmware (LCOS) is available on the device`s WEBconfig interface under "Extras > License information". If the respective license demands, the source files for the corresponding software components will be made available on a download server upon request. Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with Directives 2014/30/EU, 2014/53/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of Conformity is available at the following Internet address: www.lancom-systems.com/doc