Blueair Blue Pure 211i Max User Manual
Model: 3613111100
Safety Information
The energy efficiency of this ENERGY STAR certified model is measured based on a ratio between the model's CADR for Smoke and the electrical energy it consumes, or CADR/Watt. Blue Pure 211i Max air purifier is an electrical appliance for indoor use only. Take the necessary precautions to reduce the risk of fire, electric shock, or injury.
This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Supervise children to ensure that they do not play with the appliance.
- Cleaning and user maintenance shall not be made by children without supervision.
- Always disconnect the appliance from the power supply before maintenance.
- If your Blueair appliance is found to be defective, Blueair will replace it with the same or a similar model at no cost, per the warranty terms. Use caution attempting repairs yourself, as this presents the danger of electrical shock or injury.
- Ensure that the power cable and the power plug are not at risk of getting damaged.
- If the appliance is damaged or malfunctions, turn it off, disconnect it from the power supply, and contact Blueair.
- The power plug must be firmly inserted in the power socket.
To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact qualified personnel to install the proper outlet. Do not alter the plug in any way.
When disconnecting the unit from the power supply, do not pull on the power cord; pull on the power plug.
Use the power cable provided with your Blueair air purifier to plug directly and firmly into an appropriate electrical outlet. Do not use an extension cord or a power strip. Refer to the rating label on your appliance. Do not alter the power plug in any way. Do not use the included power cord for anything else but the appliance.
Do not allow objects to enter or block the air inlets and air outlets, as this can cause electric shock or damage the appliance. Do not place any objects on top of or directly against the appliance. Do not sit on, stand, climb onto, or hang from the appliance.
Keep the appliance, including the power cable, at a safe distance from heated surfaces and open fire. Keep the appliance and power plug away from water and other liquids. Keep the appliance and power plug away from chemicals such as pesticides and deodorants.
Place the air purifier on the floor or a stable surface to prevent tipping. Do not use the appliance outdoors or in wet environments such as bathrooms, laundry rooms, or pool areas.
Always turn off and disconnect the appliance from the power supply before moving the unit, changing filters, cleaning, or carrying out maintenance procedures. Never clean with gasoline, chemical solvents, or corrosive materials, as these agents may damage the air purifier.
Regulatory Information
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
FCC/ISED RF Exposure Information: This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Product Map
Components:
- A User interface
- B Air outlet
- C Air quality indicator (AQI)
- D Fan motor
- E Noise shield
- F Particle & carbon filter
- G Washable fabric pre-filter
Air Quality Status
The air purifier has a particle sensor to measure the fine particles (PM 1, PM 2.5 and PM 10) levels. The LED indicator displays air quality status in 5 colors from excellent (blue) to very polluted (red).
Colors: Excellent (blue), Good (light blue), Moderate (yellow), Polluted (orange), Very Polluted (red).
Getting Started
Controls:
Buttons:
- 1 ON/Standby
- 2 Night mode (lowest speed setting)
- 3 Fan speed (0-1-2-3-4)
- 4 Auto mode
- 5 Toggle
Indicators:
- 6 Filter replacement
- 7 Real-time PM values
- 8 Wi-Fi
Modes:
Auto mode: Automatically adjusts the fan speed based on your indoor PM levels to ensure optimal air quality. Recommended setting. [Auto mode symbol A]
Night mode: Lowest fan speed and fully dimmed lights. [Moon symbol]
Fan speeds 1-2-3-4: Fan speed levels which you can manually set by pressing the Fan Speed button on the interface or adjust via Blueair app.
How to Use Tips
Change Brightness
Step 1: Press the Fan Speed button and On/Standby button at the same time. Hold for three seconds.
Step 2: Then, keep holding your finger on the On/Standby button and tap the Fan Speed button with the other finger to adjust brightness. Brightness cycles from lowest to highest and back.
Enable/Disable Child Lock
Long press On/Standby button for about 5 seconds (until all the LEDs of the interface light up and blink once). Then release. When the Child lock is on, the air purifier will continue to operate but the speed/mode buttons will be locked. [5 seconds]
Filter Reset
Extra long press Fan Speed button for about 15 seconds (until all the LEDs of the interface light up). Then release. After replacing the filter, manually conduct filter reset. If done correctly, the red filter replacement indicator will blink three times and then disappear. [15 seconds]
Factory Reset
Extra long press On/Standby button for about 15 seconds (until all the LEDs of the interface light up for the second time and blink four times). Then release. After factory reset, the air purifier restarts with default configuration and will go into Standby mode. [15 seconds]
Turn Off/On Wi-Fi LED
When starting the appliance for the first time, the Wi-Fi LED will blink to signal the device is ready for pairing. After successfully connecting the appliance to the app, the Wi-Fi LED will stay solid. If you choose not to connect the product, the Wi-Fi LED can be turned off. Long press Fan Speed button for about 5 seconds and then release. The Wi-Fi LED will stop blinking. [5 seconds]
Connect to the Blueair App
Connecting to the Blueair app allows remote control and filter usage monitoring, offering additional functions.
Connection Steps:
- Download the Blueair app from the App store or Google play.
- Open the app. Create or sign into your Blueair account.
- Click on "Connect Product" and select Blue. Follow the instructions to complete app pairing.
First Time Connection Tips:
- Ensure your air purifier is on. The Wi-Fi indicator blinking means it is ready for pairing. [Power plug symbol]
- Bluetooth is required for first time pairing. Turn your phone's Bluetooth on and keep your phone within 3ft of the air purifier. [Bluetooth symbol]
- Keep your air purifier within 15 feet of your Wi-Fi router for optimal connection. [15 feet distance]
- Use a visible Wi-Fi network; VPN should be deactivated.
- This air purifier connects only to 2.4 GHz Wi-Fi. If using a dual-band router, select 2.4GHz. [2.4 GHz Wi-Fi symbol]
QR code for app download: Scan for app.
Maintenance Information
Important!
Turn the air purifier off and disconnect from the power supply before maintenance.
Changing Your Filter
When your air purifier's indicator light turns red, it's time to change the main filter. This typically occurs between 6 and 9 months of operation, depending on usage and air quality conditions.
Steps:
- Turn off and unplug the air purifier. Rotate the top counter-clockwise to unlock, then lift to remove it.
- Remove the fabric pre-filter and the noise shield.
- Use the filter handles to pull out the old filter and replace with new. Ensure to remove plastic wrapping before inserting the new filter.
- Place the noise shield back on top of the filter. Pull the fabric pre-filter over the filter and noise shield (ensure the leather tag is on the upper side of the fabric pre-filter).
- Twist the top back on and plug in the air purifier.
- Turn the air purifier back on and reset the filter indicator by pressing the Fan Speed button for 15 seconds (until all LEDs light up for the second time and blink once). Then release. [Fan symbol]
Cleaning Your Washable Pre-filter
Clean your pre-filter regularly when dusty or dirty. Vacuum the exterior with a soft brush attachment. For a deeper clean, wash according to the pre-filter's label. Hang to dry.
Steps:
- Turn off and unplug the air purifier. Rotate the top counter-clockwise to unlock and remove it.
- Remove the fabric pre-filter from the noise shield and main filter.
- Wash according to instructions on the fabric pre-filter's label. [Washing machine symbol]
- Pull the clean pre-filter back over the noise shield and main filter.
- Ensure that the leather tab of the pre-filter is on the upper part.
- Push the top cylinder down, rotate it clockwise to lock it.
Disposal and Recycling
This air purifier should be recycled as electronic waste. For questions regarding disposal, contact your local waste management.
Troubleshooting
| Issue | Potential Cause | Try This |
|---|---|---|
| There is a red circle on my air purifier's panel. | It is time to change the main filter. | 1. Change filter according to instructions. 2. Reset filter life timer: press fan speed button until red light disappears (15 seconds). |
| My air purifier is making too much noise. | Air purifiers on high speed produce more noise. Plastic sealing still on filter. Filter or pre-filter clogged/dirty, reducing airflow. | Set a lower fan speed. 1. Remove main filter, check for plastic cover. 2. Unplug, vacuum purifier and pre-filter. Clean pre-filter in washing machine. Replace main filter when indicator turns red. |
| I cannot connect my air purifier. | Too far from phone/router during setup. App not up to date. Router issues (no connection, non-standard connection). Bluetooth deactivated. | 1. Ensure phone, purifier, router are close during setup. 2. Ensure purifier is plugged in and powered on. Update Blueair app. Ensure internet is running, using 2.4GHz network, and VPN is deactivated. Ensure Bluetooth is enabled. |
| My air purifier has lost connection. | Temporary Wi-Fi disturbances. New Wi-Fi settings or router. | If purifier doesn't reconnect: Open Blueair app, select purifier, go to Product Settings, delete purifier, then reconnect via home screen. |
| My indoor air quality is not improving. | Indoor air quality is polluted. Air quality sensors are dusty/showing incorrect levels. | 1. Disconnect power cable, wait 30 seconds. 2. Ensure no objects/dust around air quality sensors. 3. Reconnect power cable. 4. Press power button. If air quality doesn't improve with use and ventilation, contact Blueair. |
For more information and troubleshooting tips, please check the Support page on www.blueair.com.
