Home - IMT
Home - IMT
Instruction Manual for IMT models including: 2BG2S-CLT20EX1, 2BG2SCLT20EX1, CLT20-Ex 4 Simple Steps, CLT20-Ex, 4 Simple Steps, Simple Steps
Intermodal Telematics BV CLT20EX1 2BG2S-CLT20EX1 2BG2SCLT20EX1 clt20ex1
File Info : application/pdf, 2 Pages, 1.15MB
DocumentDocument1 SUMMARY OF ATEX AND IECEX MARKINGS Intermodal Telematics BV · · Korte Huifakkerstraat 8 4815 PS Breda The Netherlands CLT20-Ex SERIAL NUMBER YYYY/IM20CLTXXXXX AAAAA EPT 20 ATEX 3744X IECEX EUT 20.0007X 0344 II 2 GD Ex ib IIC T4 Gb Ex ib IIIC T135ºC Db Ta: -40º C ... +60º C WARNING: Potential electrostatic charging hazard - see instructions - Clean only using a wet cloth YYYY is the year of production. XXXXX is the serial number. AAAAA is the device code. DESIGNATION ACCORDING TO DIRECTIVE 2014/34/EU: Notified body performing the QA surveillance Equipment Group II (Surface Industries) 2 Equipment Category 2 (Equipment with a high level of protection suitable for in Zone 1 areas) GD For explosive mixtures of gasses, mists, vapors or dust in air Ex marking: Ex Electrical apparatus with explosion protection acc. EN-IEC standards ib Type of protection (Intrinsic Safety) IIC Gas group T4 Temperature class Gb IEC equipment protection level Ex marking: Ex Electrical apparatus with explosion protection acc. EN-IEC standards ib Type of protection (Intrinsic Safety) IIIC Dust group T135ºC Temperature class Db IEC equipment protection level ··EU-Type Examination Certificate Number with X marking: Warning: Potential Electrostatic Charging Hazard Clean only using a damp cloth European Standards applied for explosion protection: International Standards applied for explosion protection: Ambient temperature: ATEX EPT 20 ATEX 3744X IECEx EUT 20.0007X EN IEC 60079-0:2018 EN60079-11:2012 IEC 60079-0:2017 IEC 60079-11:2011 -40ºC < Ta < +60ºC FCC ID: 2BG2S-CLT20EX1 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. 2 INSTALLATION 2.1 GENERAL The CLT20-Ex is a Communications and Location Terminal consisting of a battery powered GSM/HSPA/LTE Cat M1/NB1 modem and GPS receiver with proprietary communication for industrial applications. The battery is factory mounted and may not be replaced by the user. 2.2 INSTALLATION The CLT20-Ex is only intended for fixed installations. Always follow local regulations and IEC60079-14 (Explosive atmospheres - Part 14: Electrical installations design, selection and erection) or other local codes of practice. 2.2.1 ELECTROSTATIC DISCHARGE The CLT20-Ex has a non-metallic surface that exceeds 10.000mm2. Extensive testing has proven this to be safe when there is no risk of electrostatic charge build-up during the intended use. The following warning needs to be observed: Warning: Potential Electrostatic Charging Hazard - Clean only using a damp cloth. 2.3 ELECTRICAL CONNECTION There are no electrical connections to be made by the user. 3 INSPECTION, MAINTENANCE AND REPAIR 3.1 INSPECTION AND MAINTENANCE The requirements as stated in EN-IEC 60079-17 or other codes of practice valid at the place of installation apply. If the CLT20-Ex enclosure appears cracked, dented, broken, very dirty or otherwise no longer in good condition, it must be repaired or cleaned immediately. As the devices internal circuits are always on, in case of damage it must be removed from the hazardous area immediately and may only be restored after the repair has been carried out and approved. Cycle of maintenance depends on the specific conditions of use. As a general guideline for light use a 12 month interval is recommended. 3.2 REPAIR Repair to the CLT20-Ex may only be done using original parts. It shall be carried out by qualified skilled workers who have been trained in accordance with EN-IEC 60079-19 or other codes of practice valid at the place of installation. Repairing with non original parts may lead to personal injury and/or damage to the equipment. If non-original parts are used, or repair has been carried out in an incompetent manner, the warranties concerning explosion safety no longer apply. Therefore it is advised to return the equipment to the manufacturer in cases where a repair is required. 3.3 SPECIAL CONDITIONS FOR SAFE USE Warning: Potential Electrostatic Charging Hazard - Clean only using a damp cloth. See section 2 Electrostatic discharge Intermodal Telematics BV Korte Huifakkerstraat 8 · · Tel.: +31 (0)76 231 02 00 4815 PS Breda The Netherlands info@intermodaltelematics.com · · Version CLT20Ex-18.06.2024 Specifications are subject to change without notice www.intermodaltelematics.com Telematics Taking Over intermodaltelematics.com CLT20-Ex Installation manual 4 simple steps Version 1.2 READ BEFORE INSTALLING INSTALLATION PROCEDURE ON TANK CONTAINER (CORNER) 1 CHECK Check if an IMT L-bracket is fitted to the tank container. 2 WELD Weld the bracket in the top left triangle at the back of the tank container. 3 ATTACH Attach the CLT20-Ex using self- locking nuts. 4 SCAN Scan the QR CODE on the CLT20-Ex and follow the instructions to register the unit. MAKE SURE AN UNOBSTRUCTED EXPOSURE OF THE SOLAR PANEL TO THE SUN. www.intermodaltelematics.com INSTALLATION PROCEDURE ON TANK CONTAINER (WALKWAY) 1 CHECK Check if an IMT L-bracket is fitted to the tank container. 2 ATTACH Attach the bracket to the walkway with bolts and self-locking nuts or use a thread-lock. Utilise all three holes in the L-bracket. 3 ATTACH Attach the CLT20-Ex using self- locking nuts. 4 SCAN Scan the QR CODE on the CLT20-Ex and follow the instructions to register the unit. MAKE SURE AN UNOBSTRUCTED EXPOSURE OF THE SOLAR PANEL TO THE SUN. Any questions: support@intermodaltelematics.com INSTALLATION PROCEDURE ON RAIL WAGON 1 CHECK Check if an IMT bracket is fitted to the wagon. 2 DRILL Drill holes to the wagon according to the drawing. 3 RIVET Rivet the CLT20-Ex in place with the defined rivets. Pay attention to the correct rivet length for the wagon wall thickness. 4 SCAN Scan the QR CODE on the CLT20-Ex and follow the instructions to register the unit. MAKE SURE AN UNOBSTRUCTED EXPOSURE OF THE SOLAR PANEL TO THE SUN. www.intermodaltelematics.com