Under Desk Electric Elliptical Machine Instruction Manual

General Operation & Maintenance

Operating Instructions When Power is Off

You can use the Elliptical Trainer when it is not plugged in or when the power is off. The pedal can move forward easily, move backward is little hard.

Turning Off the Device

Correct way to turn off the device: You must first reduce the speed by pressing the speed- button on the device or on remote control, then press "POWER" button on the device or "STOP" button on remote control to turn off the device completely.

Cleaning

Before cleaning, be sure to turn off and unplug from the power supply. Do not use corrosive cleaning agents when cleaning the product. Use a dry cloth to clean the surface of the product. Do not let water enter. This product must be kept dry and not exposed to direct sunlight.

Technical Data & Safety Notices

Technical Data

Safety Notices

1. PLEASE READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE, AND RETAIN THESE INSTRUCTIONS FOR REFERENCE.
2. This product is intended solely for Leg Exercise.
3. Consult your physician before using this product if:
   • a. You are pregnant
   • b. You have been fitted with a pacemaker, an implant, or other medical aid
   • c. You suffer from diabetes
   • d. You have a circulatory disorder
   • e. You have any concerns about your health
4. Older or infirm persons should consult their doctor before using the product, even if they have no specific pre-existing conditions.
5. Stop using the product immediately if you feel discomfort or pain.
6. To avoid a short circuit, connect the device correctly and keep it away from metal (pins), rubbish and Water.
7. Use the device on a level surface. If the devise is not stable, it can tip over and cause injury.
8. Remove the adapter from the power outlet when not in use.
9. Store the device in its packaging for prolonged storage, or in a secure, dry and cool place.
10. Do not place any other objects on the device.
11. If the power cord is damaged, it must be replaced; this should only be done by an authorized and qualified person.
12. Keep the product away from moisture. Do not use if the appliance or parts of it are wet or damp.
13. Children younger than 8 years of age are to be kept away from the machine and the connecting cable.
14. To avoid injury and irreparable damage, always sit while using the device. In order to avoid serious injury, never stand on the unit or use it with excessive force.
15. Do not attempt to disassemble or repair the appliance. Repairs may only be carried out by a suitable qualified technician.

Problem Solving

[Icon: Person Standing] ❌ [Icon: Person Sitting] ✔️ Use the product only sitting, stand on the device may cause the pedal fall off or damage to the product.

Product Overview & Control Panel Operation

Product View

• [Part 1: Panel]
• [Part 2: Fuselage]
• [Part 3: Pedal Upper Shell]
• [Part 4: Pedal Under Shell]
• [Part 5: Bottom Plate]
• [Part 6: Curved Plastic Plate]
• [Part 7: Power Cord]
• [Part 8: Remote Control]
• [Part 9: Handle+Remote Control Storage Area]

Operating Instructions for Control Panel

1. Step 1: Plug in the power. Plug in the device, enter Standby mode "----".
2. Step 2: Power on. Press the POWER button. The display will show settled working time 20mins. At this time, the SCAN and TIME lights on the screen are on, as shown in the figure. (Display shows: 20.00)
3. Step 3: Adjust time. When the SCAN and TIME lights on the screen are on, Press the SPEED+/- button on the Control Panel to adjust time from 20 mins to maximum 30 mins or minimum 5 mins. (The SPEED+/- button on the control cannot adjust speed.) (Display shows: 05.00)
4. Step 4: Adjust speed in Manual Exercise (HR mode). After adjusted working time, press button POWER to start machine. By default, the product starts in Manual Exercise (HR), display will show speed 01 at first. When the SCAN and SPEED lights on the screen are on, press the SPEED+/- button at this time, you could adjust speed from 01 to 12. (Displays show: 01.00, 8.8.8.8)
5. Step 5: Switch to Auto Exercise (can't adjust speed in Auto Exercise). Press MODE button to select Auto Exercise (P1, P2, P3) or switch to Manual Exercise (HR). (Displays show: P1, P2, P3)

Control Panel Button Functions

Remote Control Functions & Exercise Programs

Remote Control Button Functions

Automatic Exercise Programs

Automatic programs are designed around a training program, so the pedals moving at different speeds and directions depending on the selected program. In Automatic Exercise programs, you can adjust the time before operation, 20mins is just a default, but the speed and direction can not be changed.

Automatic Exercise Mode P1, P2, P3:

AUTOMATIC PROGRAM P1: Daily Workout

For the group who like walking and patients or old people with mobility problems.

AUTOMATIC PROGRAM P2: Light Exercise

For office workers who lack of movement or elderly who need exercise at home.

AUTOMATIC PROGRAM P3: Intensive Training

For the people who want to burning calories and strengthen muscles.