hygger HG130 User Manual
hygger circulation and wave pump
Product Versions
The hygger HG130 pump is available in two versions:
- Switch Version: Features a switch for controlling operation.
- Non-Switch Version: The traditional model without a switch.
This product has 2 versions: the traditional one without a switch, and the updated one with a switch. You can choose the one you need.
⚠️ WARNINGS:
- To ensure performance, do not let the pump run dry.
- Be careful when assembling the magnet base. Move the magnet base parallelly to the outside wall of the fish tank to prevent it from breaking.
- Do not immerse the plug into water or other liquid.
- Do not allow children or inexperienced people to operate or play with the product alone without safety supervision.
1. Introduction
The wave-making pump can create water flow in the tank, forming large current and circulation. It is beneficial for stabilizing water quality, increasing dissolved oxygen in water, and promoting the growth of fish.
2. Product Features
- Adjustable flow direction to different angles according to needs.
- Adjustable flow rate according to needs.
- High-performance motor, low noise.
- Unique anti-reversal design.
- Wear-resistant ceramic shaft, suitable for fresh and salt water.
- Feeder function: The wave maker with a switch can be turned off when feeding the fish.
3. Product Specification
| Model | HG130-3000 | HG130-6000 | HG130-10000 |
|---|---|---|---|
| Power (W) | 4W | 6W | 12W |
| Volt/Freq | US standard: AC 110-120V/60Hz EU/UK/AU standard: AC 220-240V/50Hz |
US standard: AC 110-120V/60Hz EU/UK/AU standard: AC 220-240V/50Hz |
US standard: AC 110-120V/60Hz EU/UK/AU standard: AC 220-240V/50Hz |
| Flow rate (GPH) | 792GPH (3000L) | 1585GPH (6000L) | 2378GPH (9000L) |
| Recommend tank size | 3-15Gal (11~56L) | 16-105Gal (60L~397L) | 42-190Gal (159L~720L) |
| Recommend glass thickness | ≤0.315" (8MM) | ≤0.39"(10MM) | ≤0.47"(15MM) |
4. Installation Instructions
Installation Diagram
The pump assembly consists of the following parts:
- Prefilter
- Pump body
- Regulating ring
- Rubber strip
- Rotor
- Impeller
- Ceramic shaft
- Shaft cap (x2)
- Ceramic ring
- Rubber ring
- Holder
- Magnetic base
- Rubber foot
Installation Steps:
-
Attach Pump to Tank: Remove the rear magnet base from the bottom of the pump. Place the pump at the center of the inner tank wall and hold it with one hand. Shift the rear magnet base along the outside wall to the same position with the other hand to fix the pump. (Refer to Fig. 1: An illustration shows the magnetic base being attached to the aquarium glass from the outside, aligning with the pump inside).
Caution: Be careful of fingers being clamped due to strong magnetism. - Power Connection: Plug in the power supply. The pump can start working.
5. Pump Care and Cleaning
Follow these steps for pump maintenance and cleaning:
-
Disassemble Pump:
- Take off the pump base.
- Hold the plastic nail with your right hand and pull it to the right. Hold the front cover with your left hand and pull it to the left to separate them.
- Align the ceramic port, then insert it into the plastic cover during reassembly.
- Clean Impeller and Pump: Use a soft cloth to clean the impeller and the pump with clear water.
- Drip Loop: The power cord of the pump must be below the power socket to form a drip loop. This prevents water from flowing into the power socket along the power cord. (Illustration shows a power cord forming a U-shape loop below the wall socket).
6. Disposal
Please do not dispose of this product as unsorted municipal waste. Collection of such waste separately for special treatment is necessary. Do not put it together with domestic waste. Dispose of it at an authorized place for recycling of electrical and electronic appliances. Please consult your local seller to ensure the product is disposed of in an environmentally friendly way.
7. Package Included
- 1 × Wave pump
- 1 × User manual
8. Contact Information
E-mail: service@hygger-online.com
Website: www.hygger-online.com
