Assembly Instructions
IMPORTANT! Ensure that you have both a Connex Spot Monitor and an approved stand before proceeding with assembly.
The following parts are required for assembly:
- Connex Spot Monitor (not included in this kit)
- Approved Desk Stand
- Power Adapter
- Screws (Type A) x 2
- Screws (Type B) x 4
- Batteries (for monitor)
- NIBP Hose/Cuff
- SpO2 Sensor/Cable
- SureTemp Sensor/Cable (optional)
- Braun Thermometer Sensor/Cable (optional)
Step 1: Attach Stand Base
Align the stand base with the mounting points on the back of the Connex Spot Monitor. Secure the base using two Type A screws (? x 2).
Diagram Description: Shows the stand base being attached to the monitor's rear mounting points with two screws labeled 'A'.
Step 2: Insert Batteries
Open the battery compartment on the Connex Spot Monitor. Insert batteries (?) as indicated by the polarity markings (+/-). Close the battery compartment.
Diagram Description: Shows opening the battery cover, inserting batteries with correct polarity, and closing the cover.
Step 3: Mount Monitor onto Stand
Place the Connex Spot Monitor onto the assembled stand base. Secure the monitor to the stand using four Type B screws (? x 4).
Diagram Description: Shows the monitor being placed on the stand and secured with four screws labeled 'B'.
Step 4: Connect Power and Charge
Connect the power adapter cable to the designated port on the monitor. Plug the power adapter into a wall outlet. The monitor will begin charging. Allow approximately 2 hours (⏱️ 2h) for a full charge.
Diagram Description: Shows connecting the power adapter to the monitor and then to the wall outlet. An indicator shows charging for 2 hours.
Step 5: Connect Sensors
Connect the necessary patient sensors to the appropriate ports on the Connex Spot Monitor:
- Connect the NIBP hose/cuff to the NIBP port.
- Connect the SpO2 sensor/cable to the SpO2 port.
Diagram Description: Shows the NIBP and SpO2 ports on the monitor and the corresponding cables being connected.
Step 6: Connect Optional Accessories
6a: SureTemp® Thermometer
Connect the SureTemp sensor/cable to the designated port on the monitor.
Diagram Description: Shows connecting the SureTemp sensor.
6b: Braun Thermometer
Connect the Braun thermometer sensor/cable to the designated port on the monitor. Follow the specific instructions for the Braun thermometer accessory.
Diagram Description: Shows connecting the Braun thermometer accessory.
File Info : application/pdf, 4 Pages, 2.42MB
DocumentDocumentRelated Documents
 |
Welch Allyn Connex Spot Monitor Assembly and Setup Guide A comprehensive guide for assembling and setting up the Welch Allyn Connex Spot Monitor, including instructions for various mounting options and connections. |
 |
Welch Allyn Connex Spot Monitor Service Manual This service manual provides detailed procedures for the maintenance, repair, and calibration of the Welch Allyn Connex Spot Monitor, intended for trained service professionals. |
 |
Welch Allyn Connex Devices: Directions for Use Comprehensive guide for Welch Allyn Connex Vital Signs Monitor 6000 Series and Connex Integrated Wall System, covering setup, operation, patient monitoring, and maintenance for medical professionals. |
 |
Connex® Spot Monitor: Directions for Use Manual Comprehensive guide to the Welch Allyn Connex® Spot Monitor, detailing its features, operation, setup, patient monitoring, maintenance, and troubleshooting for healthcare professionals. |
 |
Welch Allyn Connex Spot Monitor: Directions for Use This document provides comprehensive directions for use for the Welch Allyn Connex Spot Monitor, a vital signs monitoring device used by clinicians to measure noninvasive blood pressure, pulse rate, SpO2, and body temperature. |
 |
Welch Allyn Connex Spot Monitor Service Manual This service manual provides comprehensive guidance for trained and qualified service personnel on the maintenance, repair, and troubleshooting of the Welch Allyn Connex Spot Monitor (Software version 1.X). It details procedures for disassembly, component replacement, cleaning protocols, and functional verification to ensure optimal performance and safety. Document reference: 80019225 Ver. L. |
 |
Welch Allyn Connex EVD System: Enhancing Clinical Decisions and Patient Safety Discover how the Welch Allyn Connex Electronic Vitals Documentation (EVD) System streamlines vital signs documentation, improves patient safety, and maximizes EMR investment. Learn about the Connex Vital Signs Monitor, Accessory Cable Management Stand, and Partners in Care Services. |
 |
RetinaVue™ Network Software Application Installation Instructions This document provides detailed installation instructions for the Welch Allyn RetinaVue™ Network software application, version 3.7.XX. It covers system requirements, installation procedures for new and existing users, and troubleshooting tips for medical professionals and IT personnel. |