VEVOR LED DRIVERS

Introduction

This is the original instruction manual for the VEVOR LED Drivers, Model PMA-24300A. Please read all instructions carefully before operating the device. VEVOR reserves the right to interpret this user manual. The appearance of the product is subject to the item received. Please note that VEVOR will not provide separate notification for future technology or software updates on this product.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Instructions and Warnings

General Instructions

Thank you for choosing VEVOR LED Drivers. Please read all instructions before use to achieve the best possible results.

WARNING

• Read and follow all instructions.
• Installation must comply with the NEC (National Electrical Code).
• Installation work and electrical wiring should be done by a qualified person(s) in accordance with all applicable codes and standards.
• Ensure the unit has input, output voltage, and output wattage appropriate for your application.
• Please place the LED drivers out of the reach of children to prevent children from getting an electric shock or other dangers due to curious manipulation.
• During use, do not disassemble or modify the LED drivers. If the driver shows any abnormalities, such as smoke, strange odors, abnormal noises, etc., immediately cut off the power supply and contact a professional maintenance personnel. Do not attempt to repair it by yourself.
• Please connect it to a grounded socket or power source.

Installation

• This driver must be installed in a well-ventilated area free from explosive gases and vapors. Air circulation is essential for heat dissipation.
• Recommended spacing between LED drivers should be a minimum of 4" (10cm).
• Do not mount the driver close to or above objects that can radiate heat. Vertical mounting is highly recommended.
• Select an appropriate location that is able to support the weight of the product.
• Use the mounting tabs on the left and right side of the driver to mount the product.

Diagram: Vertical Mounting: Illustrates the driver being mounted vertically using screws through its mounting tabs.

Diagram: Certified Components: Shows wire connectors and states 'Only used certified components in accordance with national and local electric codes.'

Input Connections

1. Step 1: Disconnect Power

   ⚠️ [warning symbol] Ensure power is disconnected at the source.

2. Step 2: Route Input Wires

   Diagram shows line voltage and ground wires being routed through a strain relief and knockout. Text: 'Line voltage'. Text: 'Route line voltage input wires and ground wire through strain relief and knockout.'

3. Step 3: Connect Line and Neutral

   Diagram shows wire connectors labeled 'L' and 'N'. Text: 'Connect black input wire (L) and white input wire (N) to line voltage.'

4. Step 4: Connect Ground

   Diagram shows wire connectors labeled 'G'. Text: 'Connect green wire (ground) to input ground wire.'

Output Connections

1. Step 1: Route Product Wires

   Diagram shows 'Product wires' and '0-10V/1-10V Dimming' wires being routed through a strain relief and knockout.

2. Step 2: Connect to Low Voltage Product

   Diagram shows wire connectors labeled '+' and '-'. Text: 'Securely connect driver's black wire (-) and red wire (+) to low voltage product, matching polarity.'

3. Step 3: Route Dimming Wires (if applicable)

   Diagram shows '0-10V/1-10V Dimming' wires being routed through a strain relief and knockout. Text: 'If applicable, route 0-10V / 1-10V dimming wires through strain relief and knockout.'

4. Step 4: Connect to Dimmer

   Diagram shows wire connectors labeled '+' and '-'. Text: 'Connect pink wire (-) and purple wire (+) to dimmer, matching polarity. Secure wire compartment cover when completed.'

Wiring Diagram

Using Triac Wiring Diagram

Diagram illustrates the connection of the LED driver using a Triac dimmer. It shows AC120V 60Hz input, Ground (GND), a 'Phase Dimmer', the LED driver, and the output connected to an LED strip, indicating '0-10V/1-10V Dimming' for the output control.

Using 0-10/1-10v Dimming

Diagram illustrates the connection of the LED driver for 0-10V/1-10V dimming. It shows AC120V 60Hz input (L, N), Ground (GND), a dimmer labeled '0-10V/1-10V Dimming', and the LED driver output connected to an LED strip.

Manufacturer Information

Sanven Technology Ltd.

Address: Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730