Sharper Image Heat Therapy Wraps and Rechargeable Battery

Back Wrap

Place heating area over your back with logo facing out.[Diagram: Placing the heating area over the back with the logo facing out.]

Bring the straps around your sides.[Diagram: Bringing the straps around the sides.]

Lay the strap with the logo over the other end to close it with the velcro.[Diagram: Laying the strap with the logo over the other end to close it with the velcro.]

Our Back Wrap may also be used in the front to relieve pain from menstrual cramps.

Shoulder Wrap

Place the wrap, logo facing out, so that the cupping of the wrap fits over your shoulder.[Diagram: Placing the wrap, logo facing out, so the cupping fits over the shoulder.]

Bring the longer strap around your back and under the opposite arm to the front of your chest. Put the longer strap through the loop.[Diagram: Bringing the longer strap around the back and under the opposite arm to the front of the chest, and through the loop.]

Tighten the strap and bring the velcro back over the strap so the logo is now facing out.[Diagram: Tightening the strap and bringing the velcro back over the strap so the logo faces out.]

Bring the smaller velcro strap beneath your arm and place it over the wrap as shown. It should fit securely over your bicep.[Diagram: Bringing the smaller velcro strap beneath your arm and placing it over the wrap, fitting securely over the bicep.]

Neck Wrap

Place wrap over back of neck.[Diagram: Placing the wrap over the back of the neck.]

Place straps around the neck and over one another to secure the velcro.[Diagram: Placing straps around the neck and over one another to secure the velcro.]

Wrist Wrap

Place thumb through the slit, with the wrap's logo side facing out.[Diagram: Placing thumb through the slit, with the wrap's logo side facing out.]

Wrap the strap around your wrist, making sure to support any area with slight compression.[Diagram: Wrapping the strap around the wrist with slight compression.]

Lock the strap in place with the velcro at the end of the strap by placing it over the wrap surface.[Diagram: Locking the strap in place with velcro over the wrap surface.]

Knee Wrap

Place wrap over knee, making sure the cupping of the wrap goes over the knee cap. Wrap the upper strap around your thigh and close the velcro over the wrap.[Diagram: Placing wrap over knee, cupping over kneecap, upper strap around thigh and closed with velcro.]

Wrap the lower strap around your upper calf and secure the velcro over the top of the wrap.[Diagram: Lower strap around upper calf and secured with velcro.]

You may use the wrap over either knee. To do so repeat the same directions on your other knee.

Battery Guide

Connecting the Charger

Connect the charger to the power pack.[Diagram: Connecting the charger cable to the power pack.]

Connect the charger to a power outlet.[Diagram: Connecting the charger to a power outlet.]

Fully Charge the Battery

Four blue lights indicate a full charge.[Diagram: Charger connected, showing four blue lights indicating full charge.]

Checking the Battery

Remove the battery charger plug.[Diagram: Battery charger unplugged.]

Battery Level Indicator:

• Four lights: 100% battery
• Three lights: 75% battery
• Two lights: 50% battery
• One light: 25% battery
• One light (blinking): Less than 25% battery

Powering On and Temperature Settings

To Turn Power On: Press and hold the "Power" button for 2 seconds until the controller light shows BLUE (100%).[Diagram: Controller showing power button and blue light indicating 100% charge.]

ATTENTION: Do not turn the power on when the brace/glove is folded.

High Temperature Setting

Click the "Power" button until the light changes to 75%.[Diagram: Controller showing light at 75% indicating High temperature.]

Medium Temperature Setting

Click the "Power" button until the light changes to 50%.[Diagram: Controller showing light at 50% indicating Medium temperature.]

Low Temperature Setting

Click the "Power" button until the light changes to 25%.[Diagram: Controller showing light at 25% indicating Low temperature.]

Powering Off

To Turn Power Off: Press and hold the "Power" button for 2 seconds until all lights are OFF.[Diagram: Controller showing all lights off.]

Installing the Power Pack

Locate the connector. Plug the Power Pack into the connector. Put the Power Pack into the pocket.[Diagram: Connecting the power pack to the device and placing it in the pocket.]

Fully Charge the Battery Before Storing

ATTENTION:

• Battery must be fully charged before use.
• Battery must be fully charged before it's stored, and at least once every 6 months of storage thereafter.

Wash & Care

Warning: Power Pack must be removed from device prior to washing.

Spot Cleaning Recommended:

• Hang dry
• Do not iron
• Do not use bleach or cleaning solvents
• Do not twist or wring

Specifications

• Charge time: 2.3 hours
• Output charger: 8.4V/1A

PLEASE NOTE: This is a personal care item and is returnable if in its original unopened packaging and unused condition.

Warranty/Customer Service

Sharper Image branded items purchased from SharperImage.com include a 1-year limited replacement warranty. If you have any questions not covered in this guide, please call the Customer Service department at 1 (877) 210-3449. Customer Service agents are available Monday through Friday, 9:00 a.m. to 6:00 p.m. ET.