TechOrbits Desktop Converter

Important Safety Information

CAUTION! If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact product support at 309-278-5303 or help@vivo-us.com. Ensure all parts are present and undamaged. Improper installation can lead to damage or serious injury. Do not use this product for purposes not specified in this manual. Do not exceed weight capacity. TechOrbits is not liable for damage or injury from improper mounting, assembly, or use.

• WARNING: CHOKING HAZARD Small parts - not for children under 3 years. Adult supervision is required. ?
• DO NOT EXCEED WEIGHT CAPACITY Failure to do so may result in serious injury. ⚖️
• WARNING: PINCH POINT Do not place hands on or near support bars. Moving parts can crush and cut. Pinch points exist during lifting and lowering. Follow instructions to avoid serious personal injury. ⚠️
• NEVER OPERATE RISER UPSIDE DOWN Do not attempt to raise the riser when upside down, as this can cause serious personal injury. Ensure the riser is right-side up on a stable surface before adjusting height. ⬆️
• DO NOT ROUTE CABLES WITHIN SUPPORT FRAME Routing cables within the inner support frame can cause serious personal injury and/or damage to equipment. ?
• CHECK CABLE LENGTH To prevent accidental damage to devices and/or personal injury, ensure power cables have adequate length to accommodate the chosen height of your desk riser. ?

Need Help? We're Here For You

US-Based Customer Support from Trained Professionals

Monday-Friday from 7am-7pm CST
Saturday 8am-4pm CST

Email Us: help@techorbits.com

Give Us a Call: 309-278-5303 ext. 1 ?

Package Contents

• A (x1): Desk
• B (x1): Left Bracket
• C (x1): Right Bracket
• D (x1): Keyboard Tray
• E (x2): Cable Tie
• F (x2): Pad
• G (x1): Keyboard Stop

Included Hardware

• S-A (x9): M5x12mm Flathead Screw
• S-B (x6): M5x12mm Roundhead Screw

Tools Needed:

• Phillips Screwdriver ?
• Scissors ✂️

Weight Capacity:

• Desktop: 28.6lbs (13kg)
• Keyboard Tray: 5lbs (2kg)

Assembly Steps

STEP 1: Unpack and Prepare

Carefully remove the Desk (A) from the packaging. Use a team lift if necessary. ?‍?‍?

Place the Desk (A) upside down on a protective surface and use scissors to cut the shipping ties. ✂️

WARNING: DO NOT press the handle until the desk is flipped upright. ⚠️

STEP 2: Flip and Adjust

Flip the Desk (A) upright. Use a team lift if necessary. ?‍?‍?

Pull up on the Lever to raise the Desk (A) to its highest position. ⬆️

STEP 3: Attach Keyboard Tray Components

• 3.1 Attach the Keyboard Stop (G) to the bottom of the Keyboard Tray (D) using M5x12mm Flathead Screws (S-A) and a Phillips screwdriver.
• 3.2 Attach the Left Bracket (B) and the Right Bracket (C) to the bottom of the Keyboard Tray (D) using M5x12mm Flathead Screws (S-A), ensuring the Brackets extend outwards. Tighten with a Phillips screwdriver.
• 3.3 Remove the adhesive backing from the Pads (F) and apply them to the underside corners of the Keyboard Tray (D) as shown.

STEP 4: Attach Keyboard Tray Assembly

Attach the Keyboard Tray Assembly to the Desk (A) using M5x12mm Roundhead Screws (S-B) and a Phillips screwdriver.

STEP 5: Place Devices

Place your devices onto the Desk (A).

STEP 6: Organize Cables

Organize cables using the Cable Ties (E). ?

Tension Adjustment

Why Is My Riser So Hard/Easy To Raise?

If your desk riser is difficult to lift or lowers too easily, the gas spring cable tension can be adjusted. The adjustment is located at the base of your riser.

Start by loosening the Upper (1) and Lower (2) Nuts using an adjustable wrench. Loosen Nuts until they are both on the opposite ends of the Gas Spring Cable.

1. Desk Is Difficult to Raise/Lower [How to Increase Tension]

If the desk feels difficult to raise and lower, you need to increase the Gas Spring Cable tension. Gently pull the cable upwards until the Lower Nut (2) is firmly pressed against the middle divider.

Tighten Upper Nut (1) until it firmly holds the cable in its position.

2. Desk Raises/Lowers Too Easily [How to Decrease Tension]

If the desk raises or lowers without the handle being pressed, the tension needs to be loosened. Gently push the cable downwards until the Upper Nut (1) is firmly pressed against the middle divider.

Tighten Lower Nut (2) until it firmly holds the cable in its position.

Need Help? Get In Touch

Monday-Friday from 7:00am-7:00pm CST

Email: help@techorbits.com

Phone: 309-278-5303