Specifications

• Target: GEPRC F722-BT-HD v2
• MCU: STM32F722RET6
• Gyro: ICM 42688-P
• Blackbox: 512Mb On-board SD card
• OSD: AT7456E
• Barometer: NO
• BEC 5V: 3A
• BEC 12V: 3A
• Size: 36x36mm, 4mm mounting hole
• Mounting Hole: 30.5x30.5mm
• Input Voltage: 12.6-26.2V
• Uart: 5 sets
• Features: Supporting adjust parameters by Bluetooth on Speedybee App

Connection Diagram: A visual representation shows the pinout for the SPAN F722 BT-HD v2, including connections for BEEP+, BEEP-, BAT-, BAT+, M1-M4, CURR, RX5, CAM, 5V, GND, 12V, BT, 3V3, TX1, RX1, TX2, RX2, TX3, RX3, TX5, RX5.

GEPRC SPAN 50A ESC v2

Specifications

• MCU: STM32G071(32BIT)
• Continuous Current: 50A
• Burst Current: 60A (5s)
• BEC: NO
• Current detection: YES
• Telemetry: YES
• Supports Dshot: 150-600
• PWM: 24-96K
• Target: GEPRC-G071
• Input Voltage: 12.6V-26.2V

Connection Diagram: A visual representation shows the motor outputs (Motor1, Motor2, Motor3, Motor4) and power connections (BAT+, BAT-) for the SPAN 50A ESC v2. It also indicates the pinout for TX, CUR, S4, S3, S2, S1, BAT, and GND.

Bluetooth Configuration

Steps:

1. Connect the FC to the battery.
2. Open the Speedybee app.
3. Click the Bluetooth icon on the screen.
4. Once "GEPRC F7" is found, click Connect.
5. Safety Note: Remove the propeller before plugging in the battery to adjust FC parameters.

Speedy Bee App Download: https://www.speedybee.com/speedy-bee-app/

App Stores: Available on Android and iOS.

DJI FPV Digital System Setup

Identifier Configuration:

• USB VCP: 115200
• UART1: 115200
• UART2: 115200

Receiver Setup:

• Receiver Mode: Serial (via UART)
• Serial Receiver Provider: SBUS

Input Voltage Compatibility:

• DJI AIR Unit: 7.4V-17.6V
• DJI O3 AIR Unit: 7.4-26.4V
• CADDX Vista: 7.4-26.4V

Connection Diagram: Shows connections for DJI AIR Unit, DJI O3 AIR Unit, and CADDX Vista to the flight controller.

Analog VTX Setup

Identifier Configuration:

• USB VCP: 115200, Disabled, AUTO
• UART1: 115200, VTX, IRC Tramp, AUTO
• UART2: 115200, Disabled, AUTO

Other Features: AIRMODE, OSD, DYNAMIC_FILTER

Connection Diagram: Illustrates the connection of an Analog VTX to the flight controller, including power (DC7-36V, GND, 5VOUT), video signal (VIDEO), and IRC Tramp signal.

Receiver: TBS/ELRS Setup

Identifier Configuration:

• USB VCP: 115200
• UART1: 115200
• UART2: 115200, Serial RX Enabled

Receiver Setup:

• Receiver Mode: Serial (via UART)
• Serial Receiver Provider: CRSF

Connection Diagram: Shows the wiring for GEPRC ELRS and TBS Nano RX receivers to the flight controller.

Receiver: R-XSR Setup

Identifier Configuration:

• USB VCP: 115200
• UART1: 115200
• UART2: 115200, Serial RX Enabled

Receiver Setup:

• Receiver Mode: Serial (via UART)
• Serial Receiver Provider: SBUS

Connection Diagram: Depicts the wiring for the Frsky R-XSR receiver to the flight controller.

GPS Setup

Ports Configuration:

• USB VCP: Disabled, AUTO
• UART1: Disabled, AUTO
• UART2: Disabled, AUTO
• UART5: GPS, AUTO

GPS Configuration:

• Protocol: UBLOX
• Features: Auto Baud, Auto Config, Set Home Point Once, Accelerometer, Barometer (if supported), Magnetometer (if supported)

Connection Diagram: Shows the GPS module connection to the flight controller via SDA, SCL, RX, TX, GND, and 5V pins.

Buzzer & LED Board

Beeper Configuration: GYRO_CACIBRATED, RX_LOST, RX_LOST_LOADING

Other Features: TELEMETRY, LED_STRIP, DISPLAY

Connection Diagram: Illustrates the connection of a buzzer and LED strip to the flight controller, including power (5V, GND) and signal pins.

Included Components

• 1 x SPAN F722-HD-BT FC
• 1 x SPAN G50A BLHeli_32 50A ESC
• 1 x XT60-11CM-14AWG Cable
• 4 x M3x30mm screw
• 4 x M3 x25mm screw
• 8 x M3 Nylon nut
• 1 x 35V 680UF Capacitor
• 1 x SH1.0 8Pin Cable
• 1 x SH1.0 to GH 1.25 6Pin Cable
• 10 x M3*8 damping rings

Contact & Support

Website: http://geprc.com

Social Media:

• Facebook: facebook.com/geprc
• Instagram: instagram.com/geprc
• YouTube: youtube.com/geprc

Manuals & Support: geprc.com/support