Kärcher VC 4 Cordless myHome

Intended Use

This device is intended for use in private households only and is designed exclusively for cleaning dry surfaces.

The following uses are not in accordance with the intended use:

• Cleaning people, animals, plants, or clothing on the body.
• Soaking up water or other fluids.
• Extraction of glowing ashes, coal, cigarettes, or other flammable or easily inflammable substances.
• Use in the vicinity of explosive or highly flammable substances.

Environmental Protection

Packaging materials are recyclable. Please dispose of packaging in accordance with environmental regulations.

Electrical and electronic appliances contain valuable, recyclable materials and often components such as batteries, rechargeable batteries, or oil. If handled or disposed of incorrectly, these components can pose a potential threat to human health and the environment. However, these components are required for the correct operation of the appliance. Appliances marked with this symbol ♻️ are not allowed to be disposed of together with household rubbish.

Notes on Content Materials (REACH)

Current information on content materials can be found at: www.kaercher.com/REACH

Accessories and Spare Parts

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

Warranty

Warranty conditions issued by Kärcher sales companies apply in all countries. Malfunctions will be remedied free of charge within the warranty period if a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorized customer service site.

Scope of Delivery

The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or if there is any shipping damage, please notify your dealer.

Device Description

The scope of delivery of the device (depending on the model) is shown on the packaging. These operating instructions describe all possible options. For illustrations, refer to the graphics page.

Illustration A: Device Components

• (1) Battery/error message LED indicator light
• (2) Unlocking buttons for removing the exhaust air foam filter
• (3) Exhaust air foam filter cover
• (4) Boost function button (increase suction performance)
• (5) On/Off switch with locking lever
• (6) Handle
• (7) Replaceable battery
• (8) Battery unlocking button
• (9) Unlocking button for removing the dust container removal
• (10) Air inlet filter
• (11) Dust container flap
• (12) Removable dust container
• (13) Dust container cover flap unlocking button
• (14) Dust container suction fitting
• (15) Motorized electric brush with universal brush roller
• (16) Suction pipe
• (17) Crevice nozzle
• (18) Wall bracket
• (19) Charger
• (20) 2-in-1 upholstery nozzle
• (21) Flexible extension hose
• (22) Flexible crevice nozzle
• (23) Large upholstery nozzle
• (24) 2-in-1 furniture brush
• (25) Mini turbo brush
• (26) Soft brush
• (27) LED-crevice nozzle
• (28) Air inlet filter (2x)
• (29) Filter cleaning tool
• (30) Soft motor-driven brush (Hard floor nozzle)
• (* option)

Installing the Wall Bracket

The scope of delivery includes a wall bracket as well as screws and dowels for tidy storage of the vacuum cleaner.

Note: Mount the wall bracket at a suitable point using the screws and dowels supplied. For safe storage of the device, position the lower edge of the wall bracket 1.04 m from the floor.

ATTENTION: Material damage due to incorrect installation. Incorrect installation can damage both the device and the floor covering if it falls.

Initial Startup

The device is not supplied with a charged battery. Fully charge the battery before using it for the first time. Please observe the enclosed safety instructions for battery-powered vacuum cleaners.

1. To charge the device, attach it to the wall bracket included in the scope of delivery.
2. Plug the charger into a socket. Insert the connecting plug into the charging socket of the device. The LED indicator light flashes green during the charging process.
3. When the device is fully charged, the LED indicator light lights up continuously green for 2 min. and then goes out. Remove the charger from the power socket and charging socket. Remove the device from the wall bracket. The device is ready for use.

Installing Accessories

The multi-function brush is driven by its own integrated motor and must therefore always be connected directly to the hand-held device or the suction pipe to ensure the power supply.

All other accessory parts can also be used directly with the hand-held device or with the suction pipe to increase the reach.

• Push the suction pipe onto the suction fitting of the dust container until it audibly clicks into place. Press the unlocking button and remove the suction pipe from the suction fitting. (Illustration B)
• Push the floor nozzle onto the suction pipe until it audibly clicks into place. Press the unlocking button and remove the floor nozzle from the suction pipe. (Illustration C)
• Push the accessory, such as the crevice nozzle, onto the suction fitting of the dust container or suction pipe until it audibly clicks into place. (Illustration D)

Operation

LED Display

The LED on the head of the device shows information on the charging state of the battery and error messages.

The progress of charging the battery can be read from the green LED. The LED only lights up when the battery is correctly installed.

While Charging

Error Message

Changing Accessories

To change accessories, see chapter Installing accessories.

Vacuuming

1. Install the required accessories, see chapter Installing accessories.
2. Switch on the device, depending on cleaning requirements: Press the On/Off switch and keep it pressed during operation, or turn the locking lever to switch the device directly to continuous operation. (Illustration H)
3. If necessary, press the Boost button to increase the dust intake. (Illustration I)

Note: When the device is switched off, the boost function is automatically disabled. The boost function can also be switched off by pressing the Boost button again.

Ending Operation

1. Switch off the device. Release the On/Off switch or disable the locking lever.

Note: To ensure optimum suction performance, empty the dust container and clean the air inlet filter after each use. Empty the dust container at the latest when the "MAX" marking is reached.

How to Use the Accessories

General Instructions for Use

• Which accessories are included in the scope of delivery is shown on the device packaging.
• Accessories not included in the packaging can be purchased in a Kärcher specialist shop or from www.kaercher.com.
• Test the accessory at an inconspicuous point before using it in a sensitive area.
• Follow the manufacturer's cleaning instructions.
• Connect the motor-driven electric nozzle to the suction pipe or the hand-held device.
• Also connect the other accessory parts, such as crevice nozzle, to the hand-held device or push it directly onto the suction pipe to increase the reach.

Motor-driven Multi-function Brush

Ideal for hard floors and carpets. The motor-driven multi-function brush removes dirt stuck between the carpet fibres particularly effectively.

2-in-1 Upholstery Nozzle

The frame with the surrounding bristles can be taken off by pressing the unlocking button. The soft brush is suitable for furniture with hard surfaces. The wide brush is used to clean upholstered furniture, curtains, etc.

Crevice Nozzle

For edges, joints, heaters, and areas that are difficult to reach.

Soft Brush

The soft brush has particularly soft bristles for cleaning sensitive surfaces such as keyboards, lamps, etc.

Flexible Crevice Nozzle

The flexible crevice nozzle increases the reach. For cleaning hard-to-reach places, such as between car seats.

Flexible Extension Hose

Due to the extension and flexibility, hard-to-reach areas such as in the car can be reached and cleaned.

Large Upholstery Nozzle

For cleaning textile surfaces such as sofas, armchairs, mattresses, car seats, etc.

2-in-1 Furniture Brush

For gentle cleaning of sofas and delicate furniture. Depending on requirements, the accessory can be used as a furniture or upholstery nozzle by pressing the button.

Mini Turbo Brush

Efficiently removes pet hair and dust particles from upholstered furniture, mattresses, or other soft surfaces. The rotating round brush catches even the finest hair.

LED-Crevice Nozzle

For cleaning corners and hard-to-reach areas. The illumination makes even the finest dust visible in dark spaces.

Soft Motor-driven Brush (Hard Floor Nozzle)

For hard floors and sensitive wooden floors. Extracts coarse and fine dirt simultaneously.

Transportation

The battery has been tested in accordance with the relevant rules for international transport and can be transported/shipped.

ATTENTION: Moisture and heat. Risk of damage.

Storage

Store batteries only indoors in a dry place with low humidity and temperatures below 20°C.

Care and Service

General Care Instructions

Clean the device and plastic accessory parts with a commonly available plastic cleaner.

Note:

Cleaning the Air Inlet Filter

The device can be cleaned manually or using a filter cleaning device.

1. Switch off the device.
2. Manually cleaning the air inlet filter:
   • Pull the soiled air inlet filter down at the filter stick, carefully beat it and clean it with a damp cloth or running water. (Illustration K)
   • Reinsert the fully dried air inlet filter. Check for correct seating.
3. Cleaning the air inlet filter with a filter cleaning device:

   Note: A new air inlet filter must be installed in the dust container during filter cleaning.

   • Push the filter cleaning device onto the suction pipe branch and pull the air inlet filter out of the device using the filter stick.
   • Push the soiled air inlet filter into the filter cleaning device.
   • Insert a new air inlet filter into the dust container. (Illustration L)
   • Switch on the device and let it run in boost mode while turning the side cover. (Illustration M)
   • Remove the cleaned air inlet filter from the filter cleaning tool and reinsert it in the dust container after removing the new air inlet filter.
   • Check that the air inlet filter is correctly seated.

Cleaning the Dust Container and Cyclone Filter

Note: The dust container and cyclone filter can be cleaned with or without removing the dust container. We recommend removing the dust container from the device for easy cleaning.

1. Switch off the device.
2. Press the unlocking button for the dust container and remove the dust container from the hand-held device. (Illustration N)
   • Remove the cyclone filter from the dust container by turning it anticlockwise.
   • Remove the cyclone filter from the dust container and take the air inlet filter out of the cyclone filter. (Illustration O)
3. Clean the dust container and cyclone filter with a soft brush or a slightly damp cloth. (Illustration P)
4. Clean the air inlet filter, see chapter Cleaning the air inlet filter.
5. Re-insert the dry dust container and cyclone filter with air inlet filter into the device and close the flap.
6. Attach the dust container to the handheld device.
   • Hold the dust container at an angle against the handheld device while holding the top on the hook of the handheld device.
   • Push the dust container upwards until the hook on the handheld device engages in the slot in the dust container.
   • The dust container must audibly click into place. (Illustration Q)

Clean the Exhaust Air Foam Filter/Replace the Exhaust Air Foam Filter

Note: The exhaust air foam filter ensures pure exhaust air. Clean the exhaust air foam filter if it is visibly dirty. Replace the exhaust air foam filter if damage is visible.

1. Switch off the device.
2. Clean the exhaust air foam filter.
   • Press both side unlocking buttons at the same time and remove the cover with the exhaust air foam filter. (Illustration R)
3. ATTENTION: Short circuit hazard. Power supply cables or contacts are located in the cover of the exhaust air foam filter. Before cleaning with water, remove the cover from the exhaust air foam filter so that the cables or contacts do not get wet.
4. Carefully tap off the exhaust air foam filter or if it is heavily soiled:
   • Pull off the cover of the exhaust air foam filter.
   • Clean the exhaust air foam filter under running water. Do not rub or brush off.
5. ATTENTION: Health risk. Exhaust air foam filters that are not completely dry when installed in the device can be a breeding ground for spores and mould. Make sure that the exhaust air foam filter is completely dry on installation.
   • Then allow the exhaust air foam filter to dry completely.
   • Fasten the cover to the exhaust air foam filter. (Illustration S)
   • Insert the exhaust air foam filter into the device until it latches into place.
   • Press the cover down in the middle to ensure that the cover sits correctly on the device. (Illustration U)
6. Replace the exhaust air foam filter:
   • Press both side unlocking buttons at the same time and remove the exhaust air foam filter. (Illustration R)
   • Remove the cover of the exhaust air foam filter and dispose of the used filter.
   • Fasten the new exhaust air foam filter to the cover. (Illustration T)
   • Insert the exhaust air foam filter into the device until it latches into place.
   • Press the cover down in the middle to ensure that the cover sits correctly on the device. (Illustration U)

Cleaning the Multi-function Nozzle

1. Switch off the device.
2. Remove accessories.
3. ATTENTION: Short circuit hazard. The multi-function brush contains electrical components. You must not immerse the multi-function brush in water or clean it with a damp cloth.
4. Clean the multi-function brush:
   • Unlock the brush roll cover/support with a coin or other object and remove it. (Illustration V)
   • Remove the brush roll from the brush opening in the direction of the arrow. (Illustration W)
   • Remove the dirt, e.g., with a brush. If necessary, tangled threads or hair can be carefully cut off with scissors.
   • Carefully clean the brush opening with a cloth or soft brush. (Illustration X)
   • Insert the brush roll at an angle and fully into the brush opening, pushing up until the cover snaps into place. (Illustration Y)

Cleaning the Mini Turbo Brush

1. Switch off the device.
2. Remove accessories.
3. ATTENTION: Short circuit hazard. The mini turbo nozzle contains electrical components. Do not immerse the mini turbo nozzle in water or clean with a damp cloth.
4. Cleaning the mini turbo brush:

Removing and Installing the Battery

Removing the Battery

1. Press the unlocking button.
2. Remove the battery from the device. (Illustration AC)

Inserting the Battery

ATTENTION: Dirty contacts. Damage to the device and battery. Check the battery mount and the contacts for soiling and clean them as necessary before inserting the battery.

Note: Use only fully charged batteries.

1. Push the battery into the mounting in the device until it audibly latches into place. (Illustration AD)

Troubleshooting Guide

The device does not start up

• Battery is empty. Charge the rechargeable battery.
• Battery is not inserted correctly. Push the battery into the mount until it locks into place.
• Battery is defective. Replace the battery.

The battery is not charging

• The charging plug/mains plug is not connected correctly. Connect the charging plug/mains plug correctly.
• The socket is defective. Check that the socket is working.
• The wrong charger is being used. Check that the correct charger is being used.

The device stops during operation or the suction performance is poor

• The battery has overheated. Stop work and wait until the battery temperature is back in the normal range.
• The accessories, the suction opening on the dust container or the suction pipes are clogged. Remove the clog with a suitable aid.
• The dust container is full. Empty the dust container.
• The filters are soiled. Clean the filters, see chapter Care and service.
• Roller brush is blocked. Remove any blockage.

Abnormal engine noise

• The accessories, the suction opening on the dust container or the suction pipes are clogged. Remove the clog with a suitable aid.

Technical Data

Subject to technical modifications.