Vandal Dome Network Camera Quick Setup Guide

1 Packing List

Accessories are different from countries and regions. Please refer to the actual product.

• L hexagonal wrench [wrench] *1
• Network access port [network port]
• Waterproof suites [waterproof seal] *1
• Stainless self-tapping screw [screw] *3
• Plastic anchor [anchor] *3
• Terminal block [terminal block] *1
• Position sticker [position sticker] *1
• Quick setup guide [guide] *1
• Optional [optional]

2 Device Port

Different devices may have different multi-core cables; The figure is only for your reference, please refer to the actual application scene.

• Power [power]
• Audio in [audio in]
• Microphone [microphone]
• Audio out [audio out]
• Speaker [speaker]
• Alarm in [alarm in]
• Alarm button [alarm button]
• Alarm out [alarm out]
• Alert light [alert light]
• Reset button [reset button] (Long press for 5s to restore factory settings)
• POE port [POE port]
• NVR/Switch [network device]

All external devices should be powered separately. There is no power voltage from the camera.

3 Device Dimension

Different devices may have different dimensions; Please refer to the actual product.

• Unit: mm
• Height: 45
• Diameter: Ø110
• Mounting hole diameter: Ø4.5
• Base height: 28.8
• Angle: 120°
• Other dimension: 85.4
• Other dimension: 55

4 Reset and Install SD Card

Micro SD [Micro SD card slot]

Reset Button [reset button]

Micro SD card is not included.

5 Device Installation

1. Mount the camera bracket to the ceiling or wall using the provided screws and anchors.
2. Connect the cables to the camera's ports:
   • Power: Connect to DC 12V or POE port.
   • Audio Input [audio in]
   • Audio Output [audio out]
   • Alarm Input [alarm in]
   • Alarm Output [alarm out]
3. Connect the camera to your network via the Network access port.
4. Secure the camera body onto the mounted bracket.

6 Login

1. Open a web browser and enter the camera's IP address. The default IP address is 192.168.0.120 if DHCP is enabled. Press Enter to access the login interface.
2. Upon first login, you will be prompted to create a new password. After setting and confirming the password, you will be redirected to the login screen.
3. Enter the username (default: 'admin') and your newly created password, then click the 'Login' button.

DHCP is enabled by default. You may need to use a search tool to find the camera's IP address.

Precautions

Please fully understand this document before using the device and strictly observe the rules herein. If installing in public places, display a clear notice such as "You have entered the area of electronic surveillance." Improper use of electrical products can lead to fire and severe injury.

WARNING

• Strictly observe installation requirements. The manufacturer is not responsible for damage caused by non-compliance.
• Conform to local electrical safety standards and use LPS-certified power adapters. Failure to do so may damage the device.
• If installed in areas with unstable voltage, ground the device to discharge high energy surges and prevent power supply burnout.
• Ensure no water or liquid enters the device during operation. If it does, immediately power off and disconnect all cables.
• Use only accessories provided with the device and ensure the voltage meets requirements.
• Avoid focusing strong light (e.g., sunlight, bright bulbs) directly on the device, as it may shorten the image sensor's lifespan.
• In areas prone to thunder and lightning, ground the device nearby to discharge high energy strikes and prevent damage.

CAUTION

• Avoid heavy loads, intensive shakes, and soaking during transportation and storage. Warranty does not cover damage from secondary packaging or transportation after original packaging removal.
• Protect the device from falls and impacts. Keep it away from magnetic field interference and avoid installing on unstable or vibrating surfaces.
• Clean the device with a soft, dry cloth. For stubborn dirt, use a cloth lightly dampened with a neutral cleanser, then dry the device.
• Do not obstruct ventilation openings. Follow installation instructions.
• Keep the device away from heat sources like radiators or electric heaters.
• Avoid moist, dusty, extremely hot or cold, or high-electric-radiation environments. Do not disassemble the device in these conditions.
• If the device is installed outdoors, implement insect- and moisture-proof measures to prevent circuit board corrosion that could affect monitoring.
• Remove the power plug if the device is idle for an extended period.
• Before unpacking, check the fragile sticker. If damaged, contact customer service. The manufacturer is not liable for artificial damage to the sticker.
• Ensure device ventilation to prevent overheating.
• Do not install the device in extremely hot, cold, dusty, high salinity, high humidity, or corrosive environments; disassembly is forbidden in these conditions.
• If the equipment is disassembled for a long time, or the device is not installed properly after debugging, it will affect the sealing, cause the equipment to fog up and not work properly.

NOTE

• For more information, please refer to the user manual.

Special Announcement

• All complete products sold by the manufacturer are delivered with nameplates, a quick setup guide, and accessories after strict inspection. The manufacturer is not responsible for counterfeit products.
• The manufacturer will update this manual for product function enhancements or changes and regularly update the software and hardware described herein. Update information will be added to new versions without prior notice.
• This manual may contain misprints, inaccurate technical information, or descriptions slightly inconsistent with the actual product. The company's final interpretation is standard.
• This manual is for reference only and does not guarantee complete consistency with the actual product. For consistency, refer to the actual product.