Owner's Manual for CVTE models including: 2AR82-SKIWB663U21, 2AR82SKIWB663U21, skiwb663u21, SKI.WB663U.2 IEEE 802.11 2T2R USB Wi-Fi Module, SKI.WB663U.2, IEEE 802.11 2T2R USB Wi-Fi Module, 802.11 2T2R USB Wi-Fi Module, 2T2R USB Wi-Fi Module, USB Wi-Fi Module, Wi-Fi Module, Module
Guangzhou Shikun Electronics Co., Ltd SKIWB663U21 2AR82-SKIWB663U21 2AR82SKIWB663U21 skiwb663u21
File Info : application/pdf, 18 Pages, 1.47MB
DocumentDocumentGuangzhou Shikun Electronic Technology Company Limited SPECIFICATION SKI.WB663U.2 IEEE 802.11a/b/g/n/ac 2T2R USB Wi-Fi Module Integrated Bluetooth 2.1+EDR/4.2/5.1 Checked by Approved by Shikun Rechecked by Approved by Please send the original back to us after you have approved and signed. Comments Approved by customer Approved by Company's seal Customer's Name: CVTE REVISION HISTORY VERSION DATE V0 2021.06.09 BOARD ID SKI.WB663U.2 A21193 PAGE All DESCRIPTION First Issued. AUTHOR Yve CVTE Content 1. Introduction ................................................................................................................. 1 2. FEATURES..................................................................................................................... 1 3. Block Diagram................................................................................................... 2 4. Package Outline and Mounting ....................................................... 2 5. Pin Definition..................................................................................................... 3 6. Product Pictures ............................................................................................... 3 7. Key Materials..................................................................................................... 4 8. General Requirements..................................................................................... 4 9. Electrical Characteristics................................................................................. 4 9.1 IEEE 802.11b Section .................................................................. 5 9.2 IEEE 802.11g Section .................................................................. 5 9.3 IEEE 802.11n HT20 Section(2.4GHz)..............................................6 9.4 IEEE 802.11n HT40 Section(2.4GHz)..............................................7 9.5 IEEE 802.11a Section .................................................................. 8 9.6 IEEE 802.11n HT20 Section(5GHz) ................................................. 9 9.7 IEEE 802.11n HT40 Section(5GHz) ................................................. 9 9.8 IEEE 802.11ac Section...............................................................10 9.9 Bluetooth Section ..................................................................... 11 10. Mechanical,Environmental and Reliability Tests12 11. Package ................................................................................................................... 15 12. Software Requirements ............................................................................. 16 13. Reflow Profile ................................................................................... 16 CVTE SKI.WB663U.2 1. Introduction SKI.WB663U.2 module is based on MEDIATEK MT7663BUN solution. MT7663B is a highly integrated single chip which features a low power 2x2 11a/b/g/n/ac dual-band Wi-Fi subsystem and a Bluetooth subsystem. The Wi-Fi subsystem contains the 802.11a/b/g/n/ac radio, baseband, and MAC that are designed to meet both the low power and high throughput application. The Bluetooth subsystem contains the Bluetooth radio which complies with Bluetooth v2.1+EDR, v4.2, and v5.1, baseband, link controller. This documentation describes the engineering requirements specification. SKI.WB663U.2 MEDIATEK MT7663BUN MT7663B 2x2 11a/b/g/n/ac Wi-Fi Wi-Fi 802.11a/b/g/n/ac MAC 2.1+EDRv4.2 v5.1 NoteThis module is mainly used in the field of IT products. 2. FEATURES Reserving System Chip Solution Band Dimensions IEEE Std. 802.11a IEEE Std. 802.11b IEEE Std. 802.11g IEEE Std. 802.11n IEEE Std. 802.11ac Bluetooth 2.1+EDR/4.2/5.1 MT7663BUN 2.4/5GHz 23.0mm*21.5mm*3.05mm SKI.WB663U.2 SMD IEEE 802.11a/b/g/n/ac + Bluetooth 2.1+EDR/4.2/5.1 2.4/5GHz IPEX 23.0mm*21.5mm*3.05mm QR-ZZPJ-017A 1 CVTE 3. Block Diagram SKI.WB663U.2 4. Package Outline and Mounting PCB QR-ZZPJ-017A 2 CVTE 5. Pin Definition SKI.WB663U.2 PIN 1 2 3 4 6 7 9 5,8,10,11,12,13,14 SYMBOL 3.3V 3.3V DM DP RESET WL_HOST_WAKE BT_HOSTWAKE GND TOP VIEW DESCRIPTION 3.3V 3.3V USB_DM USB_DP 10K 10K 10K GND 6. Product Pictures top view QR-ZZPJ-017A 3 CVTE bottom view SKI.WB663U.2 7. Key Materials 1 2 3 4 PCB MT7663BUN SKI.WB663U.2 CN4040M00012T211523 0 RFDIP160806ALM6T30 / FN-76 FR-4 , 4LAY 40MHz 8. General Requirements No. 8-1 8-2 8-3 8-4 8-5 8-6 8-7 Feature Operation Voltage Current Consumption Ripple Operation Temperature Antenna Type USB Storage Temperature Description 3.3V+/-0.3 700mA 100mV 0°C to +40°C External antenna High Speed USB 2.0 Interface -40°C to +125°C 9. Electrical Characteristics 25±5 3.3V±10% The Test for electrical specification was performed under the following condition unless otherwise specified. Ambient condition Temperature :25 ± 5; Power supply voltages3.3V (±10%) input power at the Module. QR-ZZPJ-017A 4 CVTE SKI.WB663U.2 10. Mechanical,Environmental and Reliability Tests Test Items Test Conditions Qty Criteria Condition QR-ZZPJ-017A 12 CVTE 10-1 10-2 Drop test Vibration test The packed samples within 100Kg can be tested Drop height: Face Side: 800/600/450mm Edge line: 600/450/350mm Drop time: 1 each Face and edge. X-Y-Z direction, first Frequency changing from 10Hz to 30Hz to 10Hz,amplitude 0.75mm, 5 times vibrations, then frequency Changing from 30Hz to 55 Hz to 30 Hz, amplitude 0.15mm, 5 time vibration. SKI.WB663U.2 After drop test, the outer box and inner 1xB box will not been broken by appearance ox visual inspection. After test, the Appearance, Power EVM 3 and Frequency error shall be satisfied with the specification. 10-3 Impact test Impact acceleration: 50m/sec2; Impact duration: 16ms Impact times: 1000. 10-4 Soldering ability test Soldering temperature: 235±5 Soldering duration: 2±0.5S 10-5 Humidity test Leave samples in 40±3, 93% RH @ 96 hours After test, the Appearance, Power EVM 3 and Frequency error shall be satisfied with the specification. 1. After soldering, the soldered area must be covered by a smooth bright solder layer, some deficiencies such as a small amount of the pinhole, not wetting are 3 allowed, but the deficiencies can not be in the same place 2. At least 90% of soldered area shall be covered continuously by the soldering material. Leave samples in standard test condition for 2 hours then test, the Appearance, 3 Power, EVM and Frequency error functional parameter shall be satisfied with the test specification. 10-6 High temperature load life test Thermostat cabinet temperature: 55±5 Applied voltage: 110% rated voltage Working duration: 200 hour After test, leave samples in standard condition for 1 hour and test, Power, EVM 60 and Frequency error shall be satisfied with the test specification. QR-ZZPJ-017A 13 CVTE 10-7 10-8 High temperature load test (Supply Voltage Cycle 23h power on, 1h power off) Temperature: 55±5 Samples work for 16 hours Low temperature storage test Leave the samples in -25±3@24 hours 10-9 Low temperature load test Leave samples in -15±3@ 2 hours, samples' function shall be normal, the let samples work for 1 hour 10-10 Temperature circle test One cycle duration -10±3@3H 40±3 @3H Total cycle: 10x 10-11 Continuous TP test Twice cycle duration -10±3@4H +60±3@4H, +25@2H@2H 10-12 ESD Discharge voltage: 1kV C: 150pF Discharge resistance330 Positive10 times 1 time for each second SKI.WB663U.2 After test, the Appearance, Power, EVM 3 and Frequency error shall be Satisfied with the test specification. Leave samples in standard test condition for 2 hours then test, the Appearance, 3 Power, EVM and Frequency error shall be satisfied with the test specification. After test, leave the samples in standard condition and tested the Appearance, 3 Power, EVM and Frequency error shall be satisfied with the test specification. After test, leave the samples in standard condition and tested Power EVM and 3 Frequency error shall be qualified and all the characters shall be satisfied with the test specification. During test, There will not been appeared 3 signal disconnection or interruption between DUT and AP. The products can recoverable smoothly 3 after ESD test. QR-ZZPJ-017A 14 CVTE 11. Package 1 SKI.WB663U.2 2 550pcs =8*550=4400 PCS 3 4 QR-ZZPJ-017A 15 CVTE SKI.WB663U.2 12. Software Requirements The driver supports the following operating systems: Microsoft Windows XP, Vista and Win7. Windows XPVista win7 13. Reflow Profile QR-ZZPJ-017A 16 CVTE SKI.WB663U.2 QR-ZZPJ-017A 17 CVTE FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. The device must be professionally installed The intended use is generally not for the general public.It is generally for industry/commercial use. The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not normally required. the user has no access to the connector. Installation must be controlled. Installation requires special training This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS and DSS) and CFR 47 FCC Part 15 E (NII). It is applicable to the modular transmitter This radio transmitter 2AR82-SKIWB663U21 has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. The concrete contents to check are the following three points. ) Must use the antenna with gains not exceeding those shown in the table below. ) Should be installed so that the end user cannot modify the antenna ) Feed line should be designed in 50ohm Fine tuning of return loss etc. can be performed using a matching network. Note: 1. GANT = GANT (without Cable) - Cable Loss; 2. For the first time C2PC, there are three different types of antennas in use. For the Radiated Bandedge and SpuriousEmission, all the antennas have been tested, only the worst data for A100-0062 antenna was recorded in the report. 3.For the third time C2PC, there are seven different types of antennas in use. The antenna used in the test had the highest gain of material number 61005-00718 and 61005-00719 Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1) L'appareil ne doit pas produire de brouillage; 2)L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems Les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit; le gain maximal d'antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.; for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate; and le gain maximal d'antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz)doit se conformer à la limite de p.i.r.e. spécifiée pour l'exploitation point à point et non point à point, selon le cas. This device is designed for use in flat panel displays operating at least 20cm from persons and Indoor use only. This radio transmitter [IC ID: 24728-SKIWB663U201] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Le présent émetteur radio 24728-SKIWB663U201 a vété approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'é metteur. Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: " Contains IC: 24728-SKIWB663U201" any similar wording that expresses the same meaning may be used. l'appareil hôte doit porter une étiquette donnant le numéro de certification du module d'Industrie Canada, précé dé des mots « Contient un module d'émission », du mot « IC: 24728-SKIWB663U21 » ou d'une formulation similaire exprimant le même sens, comme suit The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 etla conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne surl'exposition et la conformité de rf. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ouémetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps. This radio transmitter 24728-SKIWB663U21 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain Le présent émetteur radio 24728-SKIWB663U21 a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'émetteur. The concrete contents to check are the following three points. ) Must use the antenna with gains not exceeding those shown in the table below. ) Should be installed so that the end user cannot modify the antenna; ) Feed line should be designed in 50ohm Fine tuning of return loss etc. can be performed using a matching network. Le contenu concret à vérifier sont les trois points suivants. ) Les antennes dont le gain ne dépasse pas celui indiqué dans le tableau ci - dessous doivent être utilisées. ) doivent être installés de façon que l'utilisateur final ne peut pas modifier l'antenne ) La ligne d'alimentation doit être conçue en 50ohm Le réglage précis de la perte de rendement, etc. peut être effectué en utilisant un réseau correspondant. Items Original First time C2PC First time C2PC First time C2PC Second time C2PC Antenna Antenna type 1 FPC Antenna 2 Dipole Antenna 3 Dipole Antenna 4 Dipole Antenna 5 FPC Antenna Max. Antenna Gain BT&BLE(2402-2480MHz): 1.5 dBi 2.4GHz WiFi(2412-2462MHz): 1.5 dBi 5GHz WiFi(5150-5850MHz: 1.45 dBi BT&BLE(2402-2480MHz): 2.44 dBi 2.4GHz WiFi(2412-2462MHz): 2.44 dBi 5GHz WiFi(5150-5850MHz: 5.2 dBi BT&BLE(2402-2480MHz):3.17 dBi 2.4GHz WiFi(2412-2462MHz): 3.17 dBi 5GHz WiFi(5150-5850MHz: 4.33 dBi BT&BLE(2402-2480MHz):2.97 dBi 2.4GHz WiFi(2412-2462MHz): 2.97 dBi 5GHz WiFi(5150-5850MHz: 3.14 dBi BT & BLE (2402-2480MHz): 2.47 dBi 2.4GHz WiFi (2412-2462MHz): Antenna1:4.41 dBi Antenna2:4.23 dBi 5GHz WiFi (5150-5850MHz): Antenna 1:5.19 dBi Antenna 2:5.10 dBi Note: 1. GANT = GANT (without Cable) - Cable Loss; For the first time C2PC, there are three different types of antennas in use. For the Radiated Bandedge and Spurious Emission, all the antennas have been tested, only the worst data for A100-0062 antenna was recorded in the report. Notice to OEM integrator Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual(FCC/ICanada statement). Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID: 2AR82-SKIWB663U21 IC: 24728SKIWB663U21 The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer's instruction manual. This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. Any company of the host device which install this modular should perform the test of radiated & condicted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement. Then the host can be sold legally. This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.247 and 15.407) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID: 2AR82-SKIWB663U21 and Contains IC: 24728SKIWB663U21 l'hôte doit utiliser l'instrument uniquement dans des dispositifs qui répondent à la fcc / (catégorie d'exposition rf mobile, ce qui signifie le dispositif est installé et utilisé à une distance d'au moins 20 cm de personnes. le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen déclarations de conformité relatives à l'émetteur que de montrer dans ce manuel. le fabricant est responsable de la conformité de l'hôte, le système d'accueil avec le module installé avec toutes les autres exigences applicables du système comme la partie 15 b, ices - 003. accueillir le fabricant est fortement recommandé de confirmer la conformité avec les exigences de la fcc / (émetteur lorsque le module est installé dans l'hôte. le dispositif d'accueil doivent avoir une étiquette indiquant contient FCC ID:2AR82SKIWB663U21IC: 24728-SKIWB663U21